Question about 2005 Suzuki Boulevard C90T

Open Question

How does one adjust the clutch. I would like the clutch to grab sooner than it is now. It grabs almost when totally in the out position.

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: I had a recall on my 2008 CBR 1000. I had the

take off the clutch insp plate loosen the locking nut adjust the rod back then full on then back one eighth of a turn..

Posted on Apr 26, 2009

Ad
  • 2336 Answers

SOURCE: Clutch

you can adjust the play by tightening or losening the cable.

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000fxdwg I am having problems adjusting clutch crunching gears and sometimes stalling when engaging first ?


Hi gonna explain the problem an the fix.Take it to a very good motorcycle shop tell them you want the clutch changed the clutch cable changed and a full tune -up oil an the works let them know the clutch was grabbing.It will be fixed it sounds like the clutch plates might be warped an grabbing not an adjustment issue the plates aren't releasing inside the engine and are locking up. ......Good Luck hope this helped old bike mech :-)

Oct 03, 2017 | Motorcycles

1 Answer

I put new clutch cable on my banshee my clutch was grabbing when I pulled it out the garage to take it for a spin it wasn't grabbing. I looked to c if the cable came out but the clamp that gose to the...


Hi the cable needs slack if you take all the adjust out meaning the is no free play in the cable your taking the pressure off of the clutch plates causing it to not be engauged.

Nov 02, 2017 | Yamaha 2005 Banshee Base

1 Answer

I have a 2000 yamaha vstar 1100. My problem is that my clutch is barely grabbing when it is all the way pulled in. I've adjusted it so both at the handle bars and the clutch are extended all the way out....


There should be another adjuster down in the side cover that should get it workin right if not ebay has friction plates for around 40 it's pretty simple to replace

Feb 23, 2015 | Yamaha Motorcycles

1 Answer

Ktm 85 egine noise,and just ad topend rebuild


Instructions
    • 1 Take the motorcycle for at least a fifteen minute test drive. Use this time to determine if the clutch needs to "grab" more or less. For example, if you pull in the clutch lever and it is difficult to shift, it grabs too much. On the other hand, if when you let the clutch lever out the motorcycle is low on power, it is not grabbing enough.
    • 2 Set the motorcycle on its kickstand or, if like some dirt bikes, it does not have one, prop it against a solid object so that it will not fall over while being worked on.
    • 3 Loosen the clutch cable if the clutch needs to "grab" more, via the clutch cable adjuster bolts near the crankcase, until there is a small amount of play in the cable. You should be able to move the clutch lever just slightly with no change in the clutch's actuation.
    • 4 Tighten the clutch cable if you need the clutch to "grab" less. Tighten the cable until there is only a small amount of play left in the cable. Pulling the lever from now on will make a much larger difference in clutch actuation.
    • 5 Tighten the clutch cable adjusters near the crank case and take the motorcycle for a test ride in an open, private area. While riding, use your left hand to adjust the barrel adjuster where the cable housing meets the clutch lever to fine tune the adjustments made previously. When you feel the clutch is set up properly, return to your work area and tighten the barrel adjuster stop so that it will not loosen as you ride.

Jan 16, 2013 | Motorcycles

1 Answer

97 kx250 just replaced clutch hub, and basket. we can't put oil in yet beacuse we misplaced the plug, but when we got it all together and pulled the clutch in and pit it in gear it still grabbed.


if you tried the clutch dry it will grab. if you tried it with the oil in it and it grabbed, then adjust the cable. about 3 mil gap on the lever.

Mar 15, 2010 | 2003 kawasaki KX 250

1 Answer

Clutch problems


did you have flywheel resurfaced or replaced, also is it adjusted right. good luck.

Oct 20, 2009 | 1994 Isuzu Trooper

2 Answers

'94 VW Jetta III - clutch ''slipping''


I would have the clutch adjusted

Aug 01, 2009 | 1994 Volkswagen Jetta

1 Answer

Clutch won't fully disengage


This is not normal. Dirty oil can cause the clutch plates to grab. Try doing an oil change. Some oils and lubricants can cause the friction plates to swell which can also cause the plates to grab. Use 10w40 motor oil in the gear box. Don't use any synthetic oils, oil marked "EC", or oil with "special" additives. Stick with the major brands; Pennzoil, Quaker State, Mobil or Shell. If in hot areas like Texas or New Mexico go with 20w50.

ca87042.gif

Jul 12, 2009 | 2005 kawasaki KLX 125

1 Answer

Poland wildthing chainsaw


Take the screws out of the cover to the recoil. After removing the bar and chain, take a racthet with the correct size socket which should be a half inch; put ratchet in tightening position. Attach a pair of vise grips to the inner piece of the clutch just outside of the threads that screw onto the engine shaft. You may need to grab the grab the vise grips with a crescent wrench as close to the clutch as possible. Grab the crescent wrench and the ratchet firmly and turn, that baby should come right off. I just took my clutch and sprocket off of a poulan model 2055 a week ago and I am getting a new assembly tomorrow from poulan.It's not really hard to do, you can do it. Hope I was helpful!

Apr 26, 2009 | Poulan Pro Chain Saw 46cc 20"

Not finding what you are looking for?
2005 Suzuki Boulevard C90T Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...