Question about Honda CR 125 R Motorcycles

1 Answer

I am looking for detailed diagram of a CR125R 2001 gear lever display through motor

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Go to the site below. >>> Please rate my answer

Posted on Sep 02, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why are my gear lever lose if I put it in drive on my td5

Good day, There are number of reasons to look into, and i would like to ask this. Does it only happen whilst in drive?. Lets look at two various possibilities. Assuming in park stage, and the gear lever is loose, then the question at hand is answered. A gear lever has routes, some vehicles use ex; electronics, or, cables, or, levers. The routes to the gear box from the gear lever, is depending on these variations. How ever, overhaul symptoms could be that of from dust in the cables to loose endings in the cables or damaged for that purpose. electronics speak for themselves, from switches to fuses to broken or loose wire or sensors. As for levers the connecting rods have some bushes or links that are either broken, worn out, stretched, and so on.
If none of the above is valid then a deeper search towards the gear box is not to be left out. Worn synchros or worn balls inside automatics can be causes to a looses gear lever. Although on automatics, the "loose" gear lever symptom could be that of above mentioned.

Jun 12, 2014 | 2001 Land Rover Discovery Series II

1 Answer

1996 Honda CRM125 wiring diagram

Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1996 Honda CRM 125 wiring diagram Google Search
Honda Motorcycle Wiring Diagrams
Honda CR125R 1992 1997 Service Manual
Honda CR125R 2006 Owner Manual

Feb 29, 2012 | Honda CR 125 R Motorcycles

1 Answer

I have 2006 Honda cr125r that has developed a neutral between 3rd and 4th gears. What is the most likely cause of this?

There are a few possible causes. A slightly bent shift fork, the index wheel on the shifter not operating properly, and rider error are the usual causes. I doubt you are failing to lift the shift lever fully, so we can rule that one out. Since the other gears are indexing properly, I doubt the index wheel is bad. That leaves a slightly bent shift fork. If the shift lever is getting physically harder to move up and down when changing from a certain set of gears, i.e. 3rd to 4th or 4th to 3rd, it would tend to indicate a bad fork. This is an expensive repair and is not recommended for the novice mechanic.

May 27, 2011 | Honda CR 125 R Motorcycles

1 Answer

Honda cr125r clutch issue

I think ther was a bracket along that cable that kept it in place so it would work all the time check to see if you still have the bracket on ther if not make somethin to work

Apr 04, 2010 | 2002 Honda CR 125 R

1 Answer

Transmission won't shift gears. Lever is OK but

check the speed sensor,the output sensor,and the input sensor on the tranny

Dec 09, 2009 | 2001 Cadillac Sts

1 Answer

Gear select lever is very loose. It move forward

There is a pin that goes through the shifter that hold it in place, along with a spring just inside where the end of the shifting lever is, that makes the lever "return" after you pull it back to shift. These springs can break and bind up. Take a look at both.

Aug 14, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

Cr125r 2001 cant start after changing piston and cylinder

hi mate you need to adjust the float if theres to much fuel going through you need to take the float out and adjust it to the manual specifications but remember slot the pin out and take the float out but watch the little valve which stops the fuel where the little valve is hanging from that is the part you need to adjust

Jul 20, 2009 | 2002 Honda CR 125 R

1 Answer

97 1100 shadow spirit gear lever

Start the first and then go threw the gears. You always need the motor running to go threw the gears or rock the bike back N forf.And if they do not work leave it alone try another dealer.

Mar 20, 2009 | 1997 Honda VT 1100 C Shadow Spirit

2 Answers


I want to know- if there is a big difference between a 2001 v-star classic and , say a 2005 or 06 v star classic. Are the newer ones lighter, or advanced in some way, enough to make a difference?

Mar 02, 2009 | 2001 Yamaha V Star 1100 Classic

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers


Level 3 Expert

79186 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides