Question about 1986 kawasaki GPz 1000 RX

2 Answers

I have a 1986 ninja 1000r it will start and idle but as soon as i start to take off and get to bout 15 mph it will die?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try checking the side stand cut out switch, the same symtoms happened with my gpz 1000. i bypassed the switch all together.

Posted on Nov 25, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • kawasaki Master
  • 1,508 Answers

This sound like a fuel supply problem, perhaps the fuel tap is stuck. you could try it with the tap in the pri (prime) position, if this helps it may need a new fuel tap rebuild kit

Posted on Sep 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 Kawasaki Ninja 1000R how to replace the starter clutch


Hi, Gary, unfortunately, you do not have to remove the engine the starter clutch is a separate mechanical gear driven component that is activated by the starter motor, it engages the clutch pack gear or the flywheel gear to turn over the engine. It has an internal mechanism that allows the gear to turn in one "ONE DIRECTION" only and once the engine starts allows the gear to free spin with engine rotation. If the starter gear free spins in "BOTH DIRECTIONS" then the drive gear has failed, it might be serviceable on some models but usually needs to be replaced.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Gpz900R Starter Clutch Removal and Repair
86 Kawasaki ZX1000 Starter Clutch Part 1
Kawasaki Ninja ZX 10R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 10R 2015 Owner Manual

Feb 09, 2018 | kawasaki Motorcycles

1 Answer

Why doesn't it continue running after start up?


Carburetor idle circuit is not working - carb needs to be cleaned and reset to restore normal operation.

Feb 14, 2016 | 1986 Nissan Pickup 4WD 1986

1 Answer

2000 Kawasaki ZX-6R Ninja dies with throttle


Hi, Anonymous and the usual suspects are:
1. Idle port, transfer ports, slow air jet clogged.
2. Idle adjusting screw set too low.
3. Air fuel mixture adjustment too lean.
4. Pilot/slow fuel jet clogged.
5. Faulty accelerator pump.
6. Float level too low.
7. Float bowl contaminated old fuel, water, dirt, rust, etc.
8. Carburetor bowl vent line clogged/blocked/pinched.
9. Fuel line to carburetor kinked or pinched.
10. Fuel filter clogged.
11. Intake manifold leak.
12. The gas cap is not venting properly or fuel tank venting system blocked.
13. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
14. Needle and seat stuck closed in the float bowl.
15. Multi carburetors not in sync.
16. Faulty fuel pump or internal fuel line has pinholes.
17. Fuel injectors clogged or faulty.
18. Faulty throttle position sensor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Ninja starts but dies when open the throttle
http://www.newninja.com/forums/f161/zx-6r-starts-fine-but-dies-when-throttle-is-applied-16041.html
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

May 18, 2014 | 2000 kawasaki ZX-6R Ninja

1 Answer

85 600r Ninja runs idles up n down run 70 mph for 10 mins engine dies and then hard to start


You are in the wrong prduct section, this is for cars and trucks.

Jun 05, 2013 | Cars & Trucks

1 Answer

2004 Kawasaki Ninja 250R dies with throttle


Hi, Ixitjbixi and the usual suspects are:
1. Idle port, transfer ports, slow air jet clogged.
2. Idle adjusting screw set too low.
3. Air fuel mixture adjustment too lean.
4. Pilot/slow fuel jet clogged.
5. Faulty accelerator pump.
6. Float level too low.
7. Float bowl contaminated old fuel, water, dirt, rust, etc.
8. Carburetor bowl vent line clogged/blocked/pinched.
9. Fuel line to carburetor kinked or pinched.
10. Fuel filter clogged.
11. Intake manifold leak.
12. The gas cap is not venting properly or fuel tank venting system blocked.
13. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
14. Needle and seat stuck closed in the float bowl.
15. Multi carburetors not in sync.
16. Faulty fuel pump or internal fuel line has pinholes.
17. Fuel injectors clogged or faulty.
18. Faulty throttle position sensor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Engine Issues Bike Dies when given throttle ninjette org
Ninja starts but dies when open the throttle
Kawasaki Ninja 250R Service Manual
OEM Parts for Kawasaki
2004 Kawasaki NINJA 250R Owner Manual

Mar 15, 2013 | 2004 kawasaki Ninja 250R

1 Answer

I have a 1986 ninja 1000r i have replaced the pickup coils and the starter lock out switch on the clutch handel but every now and then it will just die.when i flip the clutch handle it will start righ


Hi, for the sympthoms described i'ts a electric problem on the switch . Check for corroded connectors and/or broken wiring.
Congatullations for having a real classic. I had a 600 ninja (also 1986) geat machines
Good luck
Francisco

Nov 14, 2011 | Motorcycles

1 Answer

FORK OIL CAPACITY FOR 87 NINJA 1000R


ex500 models others will be similar it takes 352ml of oil
per fork. 15wt oil is what is manufacures speck for fork oil

Jul 24, 2009 | 1999 Honda CBR 1000 F

1 Answer

No power doesnt Idle


blow head gasget, if there is no power i would change the oil pump to.

Mar 11, 2009 | 1986 Buick Somerset

Not finding what you are looking for?
1986 kawasaki GPz 1000 RX Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers

yadayada
yadayada

Level 3 Expert

79123 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...