Question about 2003 Honda VT 750 C2 Shadow

1 Answer

How to take off the rear tire with a drive shaft

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Center stand the bike,loosen the rear axel nut, take out the bolt, knock out the spacer on the brake panel, unhook the brake cable , unbolt the bar going to the brake panel, grab the wheel, and slide it sideways away from the final drive. The wheel should slide right off the spline of the final drive and roll out the back under the fender. If the wheel wont slide past the final drive let the air out of the tire. Be sure to coat the spline of the final drive with moly60 paste from your local Honda dealer when reassembling.

Posted on Aug 30, 2010

Testimonial: "thank you it was very helpful. I need to know how to change the tire myself because it cost me 3 to 400 dollars everytime i have a flat"

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 125 Answers

SOURCE: 1977 honda goldwing rear tire removal never had

Get a service manual.
there are two ways to go. both time consuming and of moderate difficulty.
My favorite is to remove the trunk, saddlebags, rear fender as a unit. Then the tire is in the open to work on. Not an easy job.

Posted on Jun 16, 2009

DoubleClutch
  • 376 Answers

SOURCE: how to change a tire on a suzuki s5o boulevard

Loosen the castle nut on the right side of the bike and push the axel bolt threw the other side. Remove the spacer that is on the right side. pull the wheel to the right and it should come off.

Posted on Sep 29, 2009

  • 101 Answers

SOURCE: Removal of motorcycle rear tire/shaft driven

The final drive assembly has to be unbolted from the swingarm and it is removed with the rear wheel. Once the assembly is off the bike, the axle can be removed and the final drive separated from the wheel.

Posted on Oct 05, 2009

  • 409 Answers

SOURCE: how to remove the rear tire with shaft drive

Pull the rear axle, and spacer on the brake side of wheel. Un hook brake rod and brake strut. Position yourself on the brake side of the bike and pull the rear wheel straight out of the final drive housing. Put a little grease on thhe final drive splines upon reinstalling the wheel to aid removal next time.

Posted on Apr 02, 2010

ckoira57
  • 267 Answers

SOURCE: how to remove rear tire it is shaft driven...

http://www.motorcyclespecs.co.za/Coments.htm

This site has tyre changing techniques for all manner of tyres, wheels and final drive systems.
Cheers.

Posted on May 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace a tire on back of a 2003 yahama v star and its shaft driven so how do i go about it


This should help you a fair bit, it's not that big a job.
Instructions below found at:
http://motorcycle.justanswer.com/questions/1ayag-remove-rear-wheel
---------------------------------
In addition to the obvious of elevating the back of the motorcycle to get the weight off the rear tire, you need to unbolt the final drive from the swing arm and remove the final drive and rear wheel as an assembly. The drive shaft will come out with the final drive, not a problem.

Once you get the assembly off the bike, you can remove the axle then separate the final drive from the rear wheel and do what you needed to do.

When you go to re-install the drive shaft, you have to align the splines. Sometimes it is easier to put the bike in gear so the female splines on the intermediate shaft don't turn as you rotate the rear wheel to insert the drive shaft.
When you go to put it back together, just tighten the bolts that hold the final drive to the swing arm evenly in a crossing pattern until tight.

As an aside note, while you have it off, make sure you grease the splines on the end of the drive shaft and the splines for the rear wheel before putting it back together
---------------------------------

All the best, plainnash

Jun 09, 2011 | Yamaha V Star 1100 Classic Motorcycles

2 Answers

The drlive line goes into what part


The Drive Line is a general term that describes a variety of parts ...

Power starts with the engine ... power is transferred from the engine fly wheel through a clutch to the transmission ... through a series of gears to the 'tail shaft', the output of the transmission. The drive shaft inserts into the splines of the tail shaft. The shaft connects to the rear end where the power is divided between the rear tires through through a diferential. The axels connect to the diferential and deliver power to the hub towhich the tire is attached..

that is unless your car happens to be a front wheel drive ... which I dont think yours is.

Jun 13, 2010 | 1990 GMC Sierra

1 Answer

Need specs for changing rear and front tires for 2002 royal star venture including torx specs


I'll include the obvious, since I'm not sure exactly what you need:

Front tire - 150/80-16 Dunlop D404F or Bridgestone G705, recommended inflation 36 p.s.i.

Rear tire - 150/90-15 Dunlop D404 or Bridgestone G702, recommended inflation 36 p.s.i., 41 p.s.i. with passenger or load.

The front tire can be removed (motorcycle on lift) without loosening calipers or any other parts once axle shaft has been withdrawn; after the tire has been changed and the wheel and axle shaft is back in place, torque for the axle nut is 58 ft.-lbs (78 nm) and the pinch nut is 14 ft.-lbs. (19 nm).

The rear tire requires removal of the right saddlebag and brake caliper, as well as the axle shaft. During reassembly, the torque for the axle nut is 110 ft.-lbs. (150 nm), for the pinch nut on the swing arm 17 ft.-lbs (23 nm). Bolts for the caliper should be torqued to 30 ft.-lbs. (40 nm).

It's a good idea to lubricate the drive splines in the rear wheel and the mating shaft in the final drive while the rear wheel is out.

Apr 15, 2010 | 2002 Yamaha Royal Star Venture

1 Answer

How to remove the rear tire with shaft drive


Pull the rear axle, and spacer on the brake side of wheel. Un hook brake rod and brake strut. Position yourself on the brake side of the bike and pull the rear wheel straight out of the final drive housing. Put a little grease on thhe final drive splines upon reinstalling the wheel to aid removal next time.

Apr 01, 2010 | 1979 Yamaha TX 750

1 Answer

Rear drive shaft lock up doing 80mph on freeway.


disconnect rear drive shaft to see if tires move if not the rear end pinion gears might have a bad bearing causing the lock up.the fastest way to repair it is to replace gear box with good used one from a salvage yard.the reason I'm telling you this is because although your gear box might be repairable, it would have to be done by a professional and cost would be high.

Jan 12, 2010 | 2006 Mitsubishi Lancer Evolution

1 Answer

1999 chevrolet siverado 1500 ext cab 4wd rear drive shaft length?


it is measured by the wheel base of the truck measure from center of the front tires to the center of the rear tires this will give you the shaft application information you need .

Aug 15, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Removal of motorcycle rear tire/shaft driven


The final drive assembly has to be unbolted from the swingarm and it is removed with the rear wheel. Once the assembly is off the bike, the axle can be removed and the final drive separated from the wheel.

Jul 16, 2009 | 2005 Yamaha V Star 1100 Classic

1 Answer

Removing Yamaha rear tire (1100 Classic)


do you mean remove the wheel? tires are best left to a shop to do as they have the machine. drive shaft yes? undo all bolts thru frame to final drive casing. slacken wheel nut but do not remove spindle, pull wheel back and out of the frame the drive shaft comes with it, tace out spindle and now lift final drive from wheel, there may be a spacer which might fall out. done deal..

Feb 26, 2009 | 2001 Yamaha V Star 1100 Classic

Not finding what you are looking for?
2003 Honda VT 750 C2 Shadow Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...