Question about 2005 Honda VTX 1300 R

1 Answer

How to replace rear brakes - 2005 Honda VTX 1300 R

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Raise wheel off the ground, take off rear axle nut, take out rear axle, knock out rear brake panel spacer, unbolt brake panel stop bar, unhook brake cable/rod, grab wheel and slide off spline (away from final drive) , and roll wheel back far enough to slide out brake panel. Don't forget to grease final drive spline with moly60 paste from your local Honda dealer when you reassemble.

Posted on Aug 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you fix sponge brakes on 2009 Hyundai Accent GLS 1.6 liter?


You've obviously still got air in the lines. If you can't remove it, take it to a shop for a pressure bleed.

Jul 08, 2017 | Hyundai Cars & Trucks

1 Answer

Why do I have oil in my breaks of my 1996 Chevy


if your talking about the rear brakes its probably the differential axle seal that is leaking differential oil out of the rear end onto the brake shoes. you will have to pull the rear axle to replace the seal and clean the rear brakes/area with brake cleaner or replace the rear brakes if they are too soaked with brake fluid.

Oct 04, 2014 | Cars & Trucks

1 Answer

Adjust parking cable 99 dodge dakota -drum brakes


Unless you have replaced the cable, it should never need to be adjusted. If you can reach under the vehicle, and when wiggling the parking brake cable, if it is taut (not sagging), then it is probably adjusted properly. What usually causes the parking brake cable to appear mis-adjusted (the parking brake won't hold the vehicle), is that the self-adjusters in the rear drum brakes are not working properly. This is bad because it means that you are not getting proper braking from the rear brakes as well as having the parking brake issue. This can cause premature wear to the front disc brake pads/rotors and affect braking power and control under certain stopping conditions. Front disc brakes work so well that many people never realize that their rear brakes aren't doing their fair share. The purpose of the self-adjusters in the drum brakes is to keep the rear brake shoes at a consistent distance from the drum's inner surface as the shoe lining wears down. If the adjuster works correctly, the parking brake will always stay in adjustment. You CAN adjust the parking brake cable, but if the problem is actually with the self-adjuster, you are masking the real problem, and later on when you need to replace the rear brake shoes, you will find it impossible to put the drum back on over the shoes as the parking brake will have the shoes pushed out too far. Have a mechanic check out the self-adjuster mechanism. It is always a good idea whenever you replace the rear brake shoes to replace all the rear brake hardware as well. You don't replace rear brakes nearly as often as the front ones, and the cost of the hardware is minimal in relation to the satisfaction of knowing that non-corroded parts will work better and provide longer service than the older, gummed-up and rusted hardware that is currently installed.

Sep 11, 2014 | Dodge Dakota Cars & Trucks

2 Answers

How to adjust rear brakes on dodge dakota sport,2000?


if you have never replaced the factory rubber brake hoses , now is a good time to replace them
you probably have a small hydraulic fluid leak in 1 of the rear brake cylinders

May 04, 2014 | 2000 Dodge Dakota - All Dakota models -...

1 Answer

My rear brakes are not working at all, what needs to be replaced in rear brake assembly?


rear brakes consist of a set of shoes , 2 wheel cylinders and 2 rear brake adjustment kits then 2 drums and you have your rear brake set up

Sep 17, 2013 | Avid Juicy Ultimate Hydraulic Disc Brake ,...

1 Answer

Rear brake light will not work when brake pedal is applied, both front and rear brakes run through same sensor front brake applies rear light, but rear brake pedal doesnt. where is the problem?


It sounds like the rear brake pressure switch is bad. The wires for the front brake light switch are wired in parallel to the this switch. Replace the pressure switch in the metal brake line coming from the rear brake master cylinder going to the rear brake caliper.

Good Luck
Steve

Aug 21, 2011 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Had no auto matic adjusting lever can I put new brake shoes without replacing adjusting lever on 1994 Hyundia excel rear brake driver side


The rear brake drums are drum brakes on the 94 excel. The Excel uses the front brakes the most, so are you sure you need to replace the rear brakes?

Jan 06, 2011 | 1994 Hyundai Excel

1 Answer

2007 uplander rear brake repair - what type of brake pads came as original equipment? Ceramic or semi-metalic? The dealer service states that the original were semi-metalic. I've replaced the front...


pads last about 20k, rotors about 40,for the fronts and about 30/50 for the rears,they are all semi metallic.if you look under the car you will see the places for the jack(not to be used when working on the car OTHER than replacing a tyre.)for all manuals see "manuals"on this website(i am in england...)

Sep 29, 2010 | 2007 Chevrolet Uplander LT Minivan

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

Rear axle bearing replacement



REAR WHEEL BEARING/ HUB

Removal Procedure
  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Feb 14, 2009 | 2002 Pontiac Bonneville

Not finding what you are looking for?
2005 Honda VTX 1300 R Logo

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...