Question about 2005 Suzuki DR-Z 125

Open Question

I have a 2004 drz 125. What is the float adjustment and are the floats adjustable

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 101 Answers

SOURCE: 1998 yz 125 acts as if it runs out of fuel while

If your carb is clean ..Sounds like you should look at your kill switch ...could be loose wire inside, grounding itself out ...hope this helps! other then that could be starving for fuel (carb adjust)

Posted on Mar 27, 2009

goofduck
  • 490 Answers

SOURCE: kx 125 1998/ 99 fuel leaking out from carb

the needle and seat on the float may be bad check them

Posted on Apr 15, 2009

  • 234 Answers

SOURCE: 94 suzuki katana gsx600f idling high (around 3k to

have u check the shut off valve in carb is working

Posted on Jun 05, 2009

netrakid250
  • 52 Answers

SOURCE: 2004 honda crf 230 f

http://justkdx.dirtrider.net/floatlevel.html

i could write a long thing on here but you should just go here it will tell you every thing

Posted on Jun 06, 2009

ty05
  • 18 Answers

SOURCE: removing the carburator on a suzuki drz, 125.

It is quiet easy, you remove the seat then the fuel tank this will expose the carburetor then its simply a matter of disconecting fuel line and unscrewing attachement screws. why do you need to do this? I would be very careful doing this as any dirt or dust or grime getting in can have huge impact

Posted on Jun 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My drz400E will start on choke, but will stop when turned off, then it won't start again..Please Please ant ideas


Hi, Bunty972 and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Float needle and seat sticking.
5. Float level too low.
6. Carburetor bowl vent line clogged/blocked/pinched.
7. Idle adjusting screw set too low.
8. Air/fuel mixture screw set too lean.
9. Idle port, transfer ports, slow air jet clogged.
10. Slow fuel jet clogged.
11. Faulty fuel pump.
For more information about your issue and valuable "Free" downloads that you will need please Click on the links below. Good luck and have a nice day.
Newbie Just bought 2006 Drz only runs on choke DR 400
DRZ won run off choke
https://drive.google.com/file/d/0B0fPe4feWkfeODBhNGRiZTEtY2RlZi00YWRhLTk0M2ItMThhYTlhNmUzOGEx/view?ddrp=1&hl=en&pli=1#
OEM parts for Suzuki
http://dr-z.pl/DRZ400SM%20-%20OM.pdf

Nov 24, 2016 | 2005 Suzuki DRZ 400 E

1 Answer

How to adjust carb float level ?


Carbs off and upside down measure the distance between the top of the float and the part of the carb where the float bowl gasket goes ,with the gasket off.there will be measurement in the manual and it will be plus or minus a millimetre.you adjust it by bending the metal tag that pushes on the float needle that's joined to the float , unless it's made of plastic then it can't be adjusted.

Mar 18, 2015 | 2004 Yamaha YZF 600R

1 Answer

Grizzly 125 float level adjustment


float should be even with the carb body

Aug 25, 2014 | Yamaha 2006 Grizzly 125

1 Answer

2005 drz 125L carb hose line diagram


Might be fuel leaking from overflow. Perhaps the float valve is stuck or damaged, allowing the float bowl to overfill. Slight chance tapping on side of carb may seat the valve. If not, it will probably have to either be set, or replaced. Could possibly have some "gunk" stuck in the valve seat from the cleaning. It only takes a tiny speck of debris to hold the valve open, causing flooding. Another possible cause is that during the cleaning, the tab that adjusts the level of the float valve got bumped, changing the level.

Apr 08, 2014 | 2005 Suzuki DR-Z 125

1 Answer

Hi how do i adjust the float to get more fuel to my carb on my yamaha tw 125


Hi, you should slightly bend the float tang, so it will push the needle "later". stoth659.jpg

Nov 05, 2010 | 2001 Yamaha TW 125

1 Answer

2005 tt r 125 wont idle without choke, fuel


floats out of adjustment remove the bowl check float reset if adjustable or replace

May 09, 2010 | Yamaha TT-R 125 Motorcycles

1 Answer

Float adjustment wont idle


the floats dont often go out of adjustment, as the float needle has a rubber tip that doesent wear,
If the carb doesnt drip fuel, the level is probably ok
first try air cleaner, spark plug, dirt in idle jet or carb, tight valve clearances.

Apr 11, 2010 | 2004 Honda CRF 150 F

1 Answer

What should the compression be on a 2004 Suzuki DRZ 125?


With the throttle held wide open, the compression should be between 140 psi and 180 psi. If the compression reads lower that 140 psi, adjust the valve tappet clearances and try again. Insufficient valve tappet clearance is the most common cause of low compression in four stroke engines.

Dec 08, 2009 | 2004 Suzuki DR-Z 125

1 Answer

My TTR 125 wouldn't start after being idle for several months. I removed the bowl and cleaned it and the jets, making sure that all of the openings were clear. When I put it back together, though, it leaks...


The adjuster tang on the float (in green) rises and falls to maintain fuel level. It pushes on the float needle to stop the flow and drops to let fuel in. Did you loose the needle? If all parts are there, gently bend the tang upward to lower the gas level in the carb.

A “very helpful” rating for this answer? Thanks!

e037244.gif

Jun 28, 2009 | 2004 Yamaha TT-R 125 L

2 Answers

1998/99 kx 125 fuel leaking from carb outlet at bottom


sounds like the needle and seat may be the problem

Apr 15, 2009 | 2003 kawasaki KX 125

Not finding what you are looking for?
2005 Suzuki DR-Z 125 Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...