Question about 1991 Honda NT 400

1 Answer

I want to replace my old chain with a new one how do i do that

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

To replace the main drive chain,you need to remove the chain cover on the engine case which should have a couple of bolts or screws securing it. Loosen the back wheel by untightening the rear axle bolts and then loosen the rear adjusters either side. Make a note of their positions they need to be be the same position either side, although the new chain may need a different setting but as long as they are both the same tightness each side is what matters.Loosen the wheel and move it forward when the axle is loose and the pin holding the axle nut is removed.Unscrew the two 6mm bolts holding the front sprocket a the engine side of the chain.Turn the part on the front sprocket where the two bolts have just been removed so that it lines with the gearbox splines and pull it forward along with the front sprocket at the same time as you push the loosened rear wheel the chain should pull away from the teeth on both sprockets.
To put on the new chain just reverse the proceedure.the ajusters need to be tight but not too tight just enough play to move it up and down slightly remember both adjustes need to be the same position each side and check that the wheel is in line with the bike and straight as uneven adjustments will cause the wheel to be turned slightly off the required vertical position.

Posted on Aug 30, 2010

  • recondite08 Aug 30, 2010

    I forgot to mention that you'll also need to remove the chain link on the old chain and fit a new link which will come with the new chain. The link has a u shaped clip to secure it,this can be removed with a screwdriver and pliers. Turn the centre of the u clip and push the ends forward and remove the clip.Then remove the part of the link where the two pins fit through and pull it away from the chain.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Ryobi 10532 chainsaw chain will not turn. The chain lock is off, it is a new chain. I replaced the old chain as it caught in a stump and stopped turning


pull the chain clutch back towards the handle
it is not a chain lock but a clutch release that stops the chain from turning
pulling it back engages the clutch to drive it

Jul 13, 2016 | Ryobi Garden

Tip

Changing your drive chain


When changing the chain on your motorcycle, don't just pull the old one out and then remove the covers to thread the new one back on. With the transmission in neutral and the rear wheel off the floor, break the old chain, then using a master link attach the new chain to the old one, pull the old one around the countershaft sprocket and bcak until you can grab the new chain. Disconnect the old chain and you are ready to connect the ends of your new chain.

on Dec 20, 2009 | Motorcycles

1 Answer

Why replacement chain too long?


  • Could be a matter of bar adjustment
  • The replacement chain may not be an exact replacement

Apr 02, 2016 | Poulan PLN1514 8 Amp 14-in Electric Chain...

1 Answer

What size chain do i need for this bike


Why don't you just take off the old chain and take it with you to the bike store, since you have to return your new chain anyway and buy a new one. You don't even need to know the size, because they will match the old chain with the new chain. No guesswork required.

May 10, 2014 | Jamis Durango 2.0

1 Answer

Timing chain to big


Does it not fit the gears, or is it too loose when installed ?
Does the new chain fit the old gears ?
Is there a tensioner or guide not installed correctly ?

Aug 06, 2013 | 2001 Pontiac Aztek

1 Answer

I HAVE A POULAN PRO 260 42cc 18 inch THAT IS 5 yrs old REPLACED BAR AN CHAIN . WENT TO CUT SOME TREE LIMBS CAN NOT EVEN MAKE ONE FULL CUT AN CHAIN COMES OFF AFTER 4 TIMES WENT AN RENTED ONE.


Remove the new chain and compare it against the old one. Do the new drive teeth match the 'pitch' of the old chain? If incorrect, the chain cannot be adjusted properly and will 'climb' over the sprocket due to the chain teeth not matching the teeth on the drive sprocket. Getting the proper chain is the answer in this case. Hope this helps!

May 02, 2010 | Poulan 18" Chain Saw Replbar (small Saws)

2 Answers

I need to install a bike chain for my 10 speed


Hi
very often you need to replace the rear cluster at the same time as the chain, as it wears to the shape of the old chain and when a new chain is fitted to an old cluster it can sometimes jump, which is not fun if you are standing and pedalling up a hill ( not quite as bad for the ladies)
anyhow remove the old chain by punching a pin out of a link, and lay it on the ground next to the new chain, punch a pin out of the new chain at the same lenght.
Thread the new chain around the cogs and derailleur and fit the joiner, there are some really neat joiners that will just slot together. or you can use the link from when you sized the new chain, just press the pin back through with multy grips, make sure the joiner link is not sticky at all, or it will jump when it goes around the cluster

May 01, 2010 | Mongoose Exile 26 Men's Full-Suspension...

2 Answers

Bike chain broke on my 21speed promax A series MGX,how do i replace it?


You will need to first determine what the chain broke. If it is because of where you will need to replace the can with a new on. If it was anothe reason then you have a couple options.If you want to repair this yourself you will need to have a bicycle chain tool. Otherwise your local bicycle shop can reinstall the chain for a very low cost, less then the cost of a new chain tool.

If you are going to install it you can remove the bad link and reinstall the chain, however this will likely make you chain too short.

If you are going to replace the chain:
1. Lay the old chain out completely.
2. Cut the new chain the same length as the old chain. If using the quick link provided then make sure to cut the chain with two male ends and make it one link shorter then the original chain.
3.Start installing the chain from the rear derailleur. Start putting the chain in from the lower pulley(wheel on derailleur). Push over the lower pulley and under the upper pulley. Then back up behind and over the cassette (gears on the rear)
4. Now continue pulling the chain to the front. Go through the front derailluer and down around the chainrings.
5. Connect with the other end of the chain.
6.Use the quick link provided with the new chain or push the pin back into the chain (unless in is a shimano chain, then use the provided new pin)

Jul 12, 2009 | Mongoose MGX Maxim Dual Suspension...

1 Answer

Chain


If you're taking it off to replace the chain with a new one you can just cut it off. But, i would recomend a chain breaker. And if you are changing chains don't just yank the old one out! You will double your work. Use the old one as a guide to pull the new chain around the front sprocket. Zip-tie or lightly wire together. Else wise you're shoving your hand in places it might not go or it's cover pulling time. Yes...a voice of experience.

Nov 20, 2008 | 1998 Suzuki RG 150 Gamma

2 Answers

Chain


Yes. It’s likely that the sprockets are worn. Putting a new chain non a worn pair of sprockets will make the chain wear out faster—and replacing the sprockets without replacing the chain will sear out the sprockets. Do them as a set.

Nov 20, 2008 | 2005 Harley Davidson VRSCB V-Rod

Not finding what you are looking for?
1991 Honda NT 400 Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...