Question about Harley Davidson FXD Dyna Super Glide Motorcycles

1 Answer

Where is the drain plug for the clutch - FXD Dyna Super Glide Harley Davidson Motorcycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

I assume you're talking about the primary drain plug. It's underneath the primary at it's lowest point in the rear. Takes a Torx type wrench.

Good Luck
Steve

Posted on Aug 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove a throw out bearing on a 1997 harley


Step 1: Remove the magnetic drain plug with a wrench. (The drain plug is underneath the outer primary chain case on the left side of the motorcycle). Drain the fluid into a drain pan.
Step 2: Remove all of the screws on the clutch release cover with an Allen wrench. & also remove the clutch release cover. Discard the gasket that's located right on the inside of the clutch release cover.
Step 3: Loosen the clutch cable adjuster with a wrench to allow it to slack a bit in the clutch cable.
Step 4: Remove the retaining clip of the pushrod assembly with a pick tool. This should also release the two thrust washers located just behind the retaining clip.
Step 5: Remove the throw out bearing & Insert a new one into the same slot.
Step 6: Reinstall the two thrust washers and the retaining clip you previously removed.
Step 7: Tighten the clutch cable adjuster with a wrench.
Step 8: Replace the clutch release cover gasket and reinstall the cover by inserting and tightening the screws that you previously removed.

Aug 14, 2015 | Cars & Trucks

1 Answer

Is there a drain plug for the primary on a 2009 fatboy, 96 ci


Of course there is an inspection cover on the primary. It is called the clutch inspection cover or derby cover. The primary drain plug is right below the center of this cover and it is a 5/8 inch hex head with a 1/4 inch Allen socket in the middle of the plug head also. You fill the primary through this cover opening also and ONLY up to the bottom of the clutch diaphragm spring.

Sep 13, 2014 | Motorcycles

1 Answer

Change oil in the primary


There is a small drain plug under the clutch (derby) cover. Remove the plug and the oil will drain out. Replace the plug when the primary is empty. Stand the bike upright and pour oil into the primary after removing the derby cover. Oil is at the proper level when it touches the bottom of the clutch basket.

Sep 07, 2012 | 2000 Harley Davidson FLTR-FLTRI Road Glide

1 Answer

How do i change the clutch oil on a 2002 flht


Remove the drain plug under the derby cover. After most of the oil has drained, stand the bike upright and remove the derby cover and inspection cover. Re-install the drain plug after all the old oil has drained.. Pour oil into the primary through the inspection cover hole. Oil is at the proper level when you look into the derby (clutch) cover hole and oil is touching the bottom of the clutch.

Aug 11, 2012 | Motorcycles

1 Answer

I know where to add the oil and transmission fluid but how do i drain and add my primary chain fluid


On the underside of the primary all the way to the rear of the primary just under the clutch area is a pipe plug. Remove the plug to drain the oil. To refill the primary, remove the round derby cover from the primary over the clutch. Stand the bike straight up and fill the primary with 20W50 engine oil until the level just comes to the bottom of the clutch drum. Do not overfill or the clutch will drag.

Good Luck
Steve

Aug 03, 2011 | 2000 Harley Davidson FXST Softail Standard

1 Answer

I have a 2009 heritage softail classic and cannot locate the drain plugs for the oil and transmission. Is there any printed drawings of these locations? Thank you Jim Ragazzo


For your oil drain, look at the oil tank from the right side of the bike. On the backside down at the bottom is where the hose comes out. It runs down behind the transmission and comes out just below the chrome end plate on the transmission. Follow it on down and you'll see that it connects to the crossmember of the frame that runs under the transmission. Directly underneath this connection, under the crossmember there is a drain plug. Remove the plug and the oil will drain.

To drain the transmission, look at the chrome end plate on the transmission that the clutch cable runs into. This is the clutch release mechanism. Just below this, in the center the plate the chrome one bolts to, is a drain plug similar to a pipe plug. Remove the plug, transmission drains. Refill the transmission with 20-24 ounces of transmission lube.

Good Luck
Steve

Apr 27, 2011 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

I"m trying to locate the


To drain the transmission, look at the chrome end plate on the transmission that the clutch cable runs into. This is the clutch release mechanism. Just below this, in the center the plate the chrome one bolts to, is a drain plug similar to a pipe plug. Remove the plug, transmission drains. Refill the transmission with 20-24 ounces of transmission lube.

Good Luck
Steve

Apr 27, 2011 | 2003 Harley Davidson FXSTB Night Train

1 Answer

Where do you fill the transmission on a 2000 m2 cyclone buell motorcycle


Take cover off where u adjust clutch on primary just follow clutch cable where it enters primary to right 4 bolts get new gasket from harley take off cover below is a drain bolt take out drain old oil put back in get 2 guarts of air,cooled,wet clutch engine oil pour in where u took 4 bolts out of cover stand bike up straight or pour a little then stand bike up to see level where oil is the level should be even with bottom of clutch diaphragm spring the drain plug torque is 14-30 foot pounds of torque remeber bike up straight and the amount of oil for next time use 2 inch hole above shifter with 2 bolts has o-ring do not need to replace ever time drain replace plug torque pour exact amount u poured in primary when u took out the 4 bolts. Use wet clutch oil or u will destroy cluth material inside and u will go no where no exception otherwise have a couple hundred in bank to replace clutch and u can put any kind of oil u want just have other tranportation and not be in A hurry to get anywhere

Apr 29, 2010 | 2001 Buell M2 Cyclone

1 Answer

Where is the oil drain plug?


Harley is notorous for changing the oil drain location and type of plug they use. On a '98 model Softail, the oil drain is a large diameter hose that runs down the frame on the right hand side just behind the transmission. It has a hose clamp on it and has a metal plug in the end of the hose. Remove the plug to drain the engine oil. If it's changed, you bike is equipped with a "horse shoe oil tank" in that the tank is shaped like a horse shoe. Look on the bottom of the tank and you'll see two hoses coming off the bottom. One is a small hose and goes to the to the forwards towards the engine. The other should be a bit larger and go downwards with a plug in the end.

There is a plug just below the chrome end cover on the right hand side of the transmission that drains the transmission. To refill the transmission, there is another plug on the chrome cover itself that takes a very large (7/16") allen wrench to remove. There is a dipstick on this plug. When you drain the transmission, refill with 20-24 ounce of H-D transmission lubricant.

The primary oil drain is located on the bottom of the primary cover at the very back. Some models screw into the out primary and some go into the inner primary from below. Either way, drain the primary and replace the plug. Remove the five bolts holding the derby cover on and fill the primary with H-D primary lubricant up to the bottom of the clutch spring. Look at the clutch assembly and you'll see the aluminum outer drum. Just inwards of that, you see a black disc. This is the diaphragm clutch spring. Fill the primary just up to this spring with the bike standing as straight up as you can safely get it. The capacity is 40-44 ounces of oil. Do not overfill or it will make your clutch drag.

Hope this helps.

Apr 02, 2010 | 2000 Harley Davidson FXST Softail Standard

1 Answer

Primary drain plug 2002 dyna superglide location and transmission drain plug location


transmission drain plug points straight down on the right side of the bike just inside in the frame rail size socket to use is 5/8. primary drain plug is below he clutch cover on the left side of the bike it is a T40 torx bit to remove that drain plug

Oct 28, 2009 | 2004 Harley Davidson FXDWG - FXDWGI Dyna...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4339 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...