Question about 2002 Harley Davidson FXD Dyna Super Glide

1 Answer

Idle speed - 2002 Harley Davidson FXD Dyna Super Glide

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

If the engine is equipped with a carb, the idle speed screw is located at the top right of the carb. You may have to take the air filter cover off the air breather to see it.

If your bike is fuel injected, you'll have to take your bike to a shop.

Good Luck
Steve

Posted on Aug 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there any way to adjust the cold idle speed on ford ranger 3.0


There is a base idle speed set at the factory . From sensor inputs the PCM - engine computer controls idle speed in all conditions . There is nothing for you to change idle speed, you shouldn't even try . Will cause PCM to turn on the check engine light ,that you won't be able to turn off . If your having idle problems your best bet have a qualified repair shop check scan data .
007 Idle Speed Problems Scan Data for Idle

Aug 06, 2017 | Ford Cars & Trucks

1 Answer

It idles fast if I turn the idle down it stalls running rich on top end at fast idle sometimes it will drop to a very low idle and shut off


adjust the idle mixture screws first and then adjust the idle speed screw to compensate
adjusting the idle mixture screws will alter the idle speed but when properly adjusted then adjust the idle speed screw,

Aug 24, 2015 | Motorcycles

1 Answer

The owners manual says to inspect idle speed at 160,000 mi, how is it done 2003 Honda CRV


Are you having an idle issue ??
Vehicle equipped w/Tachometer ??
Cold engine idle speed ??
Warm engine idle speed ??
Warm engine idle speed @ A/C requested on ??

May 28, 2015 | 2003 Honda CR-V

1 Answer

Correct code P0504?


What Colorado do you have ? 2 wheel or 4 wheel drive ? Sport ,sport LS 3.5L , Z71, Z71 LS. etc. what size engine ? an does it have electronic throttle control ? I have factory service info an it is not showing that code .
DTC P0506

Circuit Description

The throttle actuator control (TAC) motor is controlled by the powertrain control module (PCM). The DC motor located in the throttle body drives the throttle plate. In order to decrease idle speed, the PCM commands the throttle closed reducing air flow into the engine and the idle speed decreases. In order to increase idle speed, the PCM commands the throttle plate open allowing more air to pass the throttle plate. If the actual idle RPM does not match the desired idle RPM within a calibrated time, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:
DTC P0506 Idle Speed Low
DTC P0507

Circuit Description

The throttle actuator control (TAC) motor is controlled by the powertrain control module (PCM). The DC motor located in the throttle body drives the throttle plate. In order to decrease idle speed, the PCM commands the throttle closed reducing air flow into the engine and the idle speed decreases. In order to increase idle speed, the PCM commands the throttle plate open allowing more air to pass the throttle plate. If the actual idle RPM does not match the desired idle RPM within a calibrated time, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:
DTC P0507 Idle Speed High
Cleaning the throttle body mite take care of it !
Cleaning Cleaning An Electronic Throttle Body Safely

Jan 31, 2015 | 2005 Chevrolet Colorado

1 Answer

How to adjust the idle screw


with a screwdriver

idle speed, righty fasty, lefty slowy

idle mixture, adjust in to get fastest idle speed. Once you go to far and the engine starts trying to stall , back it back a little to fastest/smoothest idle. Readjust idle speed screw as necessary to get correct speed once happy with mixture.

Also saying what car model and year you are working on would be useful. People answering questions are not telepathic.

Sep 02, 2014 | Cars & Trucks

1 Answer

WEED TRIMMER CARBURETTOR ADJUSTMENT


Three screws. On some, there are only two screws. Some have only one screw. A few have none at all.

If there are any screws, one is nearly guaranteed to be an idle mix adjustment. With the engine warmed up & idling, turn that screw in (clockwise) 1/4 turn at a time until you can hear the idle speed drop a little. Back it out 1/4 turn and leave it alone. If the first 1/4 turn drops the idle speed, turn it OUT 1/4 turn and see if the idle speed rises more. When you get idle speed that stays the same when you make a 1/4-turn adjustment, go back to the beginning if this paragraph and repeat the first part.

If there are two or three screws, the next screw may be either an idle speed screw or a high mix screw. If it's an idle speed screw, turning it in 1/4 turn will immediately RAISE the idle speed and turning it out will LOWER the idle speed. Adjust that screw until the string head (that cuts weeds) isn't quite turning at engine idle. If it's a high mix screw, its only effect will be at full engine speed. If the engine sounds throaty, turn that screw in 1/4 turn at a time at full engine speed At some magical point, the engine sound should turn brassy. If you turn the screw in past that point, the engine will lose power because it's running too lean.

If there are three screws, then you have all three - idle mix, idle speed, and high mix.

There may be markings near the screws to identify them. Each manufacturer marks them differently, if at all. Some manufacturers simply rely on the screws' locations to indicate what they do. It'll be up to you to figure out which is which and make notes accordingly.

Aug 01, 2014 | Ryobi Garden

1 Answer

Saw will start but will not idle


Someplace near the carburetor should be an idle mix screw and an idle speed screw. There may also be a high-speed mix screw. Try turning the idle speed screw in 1/4-turn at a time until it idles. If you turn it too far, the clutch will always be engaged so the blade will never stop.

Once you get it to idle, adjust the idle mix screw in or out 1/4-turn at a time until it idles at the highest speed. Turn the mix screw in JUST until the idle speed starts to drop a little, then back it out 1/4 turn.

Now adjust the idle speed screw again until it idles smoothly at a low enough speed that the blade stops.

Jul 08, 2014 | Husqvarna Partner Gas Powered Cut Off Saw...

1 Answer

My aprila rs50 starts fine and runs fine cold but if it heats up abit you pull the throttle and it sounds like its dieng


Instructions
    • 1 Park your RSV 1000R on a well-ventilated, level area, using its kickstand.
    • 2 Start the engine and let it idle in place until the temperature gauge built into the instrument cluster indicates a minimum internal temperature of 180 degrees Fahrenheit. This is the motorcycle's ideal operating temperature.
    • 3 Take note of the engine idle speed, using the tachometer needle, while the engine is running. Ideally, the engine should idle steadily at 1,250 rpm.
    • 4 Adjust the engine idle speed to 1,250 rpm, using the idle adjuster screw hidden between the lower right edge of the fuel tank and the upper edge of the right middle fairing panel. Turn the idle adjuster screw clockwise to increase the engine idle speed, or counterclockwise to decrease the engine idle speed, using a small flat screwdriver if your RSV 1000R's frame (VIN number) precedes ZD4MEE009YS000292. A plastic knob allows the engine idle speed to adjusted by hand on RSV 1000R models with a frame (VIN) numbers starting from ZD4MEE009YS000293.
    • 5 Rev the engine two to three times and observe the tachometer. The engine should return to a 1,250 rpm idle. Adjust the engine idle speed as needed, using the method described, then rev the engine again. Problems may exist within the throttle control, fuel-injection system or engine, if the engine idle speed will not hold steady at 1,250 rpm. Contact your local Aprilia service facility for assistance.
    • 6 Stop the engine, once you have obtained a steady 1,250 rpm idle speed.

Jan 17, 2013 | Aprilia Motorcycles

1 Answer

How to set idle for 1984 mustang 3.8L, 6cyl


Technically the idle speed is not adjustable. The computer controls idle speed with the idle speed control motor.
Base idle is around 500 RPM with normal idle in park at 800.

Aug 17, 2012 | 1984 Ford Mustang

Not finding what you are looking for?
2002 Harley Davidson FXD Dyna Super Glide Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...