Question about 2002 Honda CR 250 R

1 Answer

I have striped down the forks on my cr 250 2002,fitted new seals.need to know how much oil goes in them and the correct way to fill them.been told somthing about filling the top rebound valve seprate to the oil that goes in the rest of the fork? i have 2.5 w oil to go in them and is 1ltr enough.any help would be awsom. many thanks leighton

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 42 Answers

I really don't know how much, but you don't seem to be getting an answer from anyone else either. Your local dealer should not have a problem answering this one, but if they do, respond back and I will get you an answer from mine.

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Honda CR250r and recently replaced my fork seals and fork oil. I checked the manual and the oil level says 325-405 depending on stiffeness wanted. I went for 375 and now my forks are pretty...


Hi, Robinpereira my gut tells me you either your fork oil is too heavy or you put too much in. Drain the forks and measure what comes out if it;s way over specs adjust as necessary if it's exactly what you put in then replace 350cc and see how that works.
For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2004 cr250r fork oil capacity
SHOWA FORK seal replacement CR 250 pt 1
SHOWA FORK seal replacement CR 250 PT 2
CR250 2002 2003 pdf
http://www.partsfish.com/page/oem-parts-for-honda
Honda CR250R Owner Manual Competition Handbook

Jun 03, 2017 | 2003 Honda CR 250 R

1 Answer

How to change fork seals on usd forks on kwak meanstreak and how much oil to refill


Having removed the forks, you will need to undo the lower damper bolt first, this is located on the recess inside the fork where. The spindle goes through, this will then alow you to remove the oil from the fork, and the leg will then be free from the stancion moving freely down, if the fork doesnot come apart, you will have to remove the retaining clip from the seal and pull the fork apart sliding the fork leg up the stancion and sharply pulling down on it to pull the seal out, repeat this till theseal comes out, (tip) undo the fork top nut while the forks are still fitted to the bike.

Mar 02, 2011 | 2002 kawasaki VN 1500 Vulcan Meanstreak

1 Answer

My front fork seals need replacing on my 2005 model TE450, i don't know the specifications, and exactly how much oil to use in each fork


forks need to be removed,and disasemble,and cleaned,new fork seals,reasembleb fit new seals, refit damping cartridge,fill fork with 5w fork oil upto 120mm from top,refit spring, refit fork cap

Aug 14, 2010 | Husqvarna TE 450 Motorcycles

1 Answer

How much 5w oil goes into each fork?


Using 5w oil with stock springs, your oil level should be about 100mm from the top with the fork fully compressed, damper rod pushed all the way down, and the spring out. I hope this helps and good luck. Please vote and leave a message.

Oct 30, 2009 | 2003 Honda CR 125 R

1 Answer

I have a 2003 cr 125 that i just changed the fork seals on a c-cycle suspension what are the amounts of oil that i should put in?


have two measured beakers ready for when you drain each fork then when it fills up you"ll know...but i see that you"ve already done that...on my old honda cbr my manual states12.5 oz. for left...and 12.2oz. for the right.

Sep 12, 2009 | 2003 Honda CR 125 R

2 Answers

How do i change fork seals on a Kawasaki gt 550 89' and or chec and add oil


Hi,

I was told by many people it was a hard job.
I didn't think so.

What you need is:
New Seals.
8mm Allen Key.
Half Inch Stocket bar AND Extender.
Extra Fine Sand Paper/Polishing Device.
Fork Oil + Measuring Jug.
Threaded Bar with a Two 19mm Nuts Locked to each other on one end.
Spanners.
Screw Drivers.

How to do:

First Get the Front end off the Ground (ALOT, Center Stand on Bricks for extra height.)

Remove Front Wheel and Brake Calipers.

Open Drain Philips Screw on Base of Fork (Both Sides). Dont Lose Rubber washer under screw. Watch Out Also for Oil Being under Pressure.

Remove Nut from TOP of Fork (Alowing Handles and mirrors to come loose).

From Top you can see down tube has Nut/Cap with a Square Half Inch center. Use Socket Bar (and Extender if needed) without Bit to Remove reach in and remove. Watchout for Spring Pressure under the Cap/Nut.

Use Screw Driver or Hook of some kind to remove Preload Spacers, Washers AND Spring from Fork.

Slide your Threaded Bar with19mm Nuts (Make sure they are Locked Tight together at one end) down into the Fork and let it catch on the Oil Damper at the base. You will know when it's cought because you wont be able to spin the threaded bar anymore. This will stop the Damper from spinning while you undo the Allen Bolt at the very base under the fork (Outside).

Use Allen Key to remove Bolt from Underside of Fork While having someone or somthing hold the Threaded Bar form spinning.

Now look at the Old bust/leaking Oil Seal. There will be a Clip/Locking Spring in a Groove holding it in place.

Remove Clip without Damaging any part of clip or fork.

If Everything above was Done, you can now give the slider( Bottom Part) a big tug and it will all come lose.

One Part of the Oil damper will either fall off, or be left in the slider(Bottom Part). It slides over the Damper in the base of the tube.

Clean Everything.

Clean Again.

Polish Tube.

Clean Again.

Remove Two Split Washers from base of Tube and Copper Washer. Remove Old Oil Seal.

Place New Oil Seal on Gently.

Replace back on Copper washer, followed by two split washers.

Use Grease as a kind of glue to hold the part of damper that fell off back on.

Slide Slider back onto Tube.

Screw Allen Bolt back into base of slider as per originally was (Remeber to hold Threaded Bar if it starts spinning)

Push Gently new Oil Seal into Fork Slider for Snug Fit. Be Gental.

Replace Clip/Spring over top of Oil Seal Locking it in place.

Remove your threaded bar from top of Fork.

Replace Spring into Fork.

Replace Philips Oil Drain Screw into base of fork (Dont forget Rubber washer).

Now: For a GT550 (I am told also KZ550 but can confirm) you need 300ml of 15 weight Fork Oil. EACH Fork. So a Total of 600ml whole Job. IN EACH SIDE YOU WILL ADD ONLY 300ml of FORK OIL. (15w)

After this. Replace any washers, Preload Spacers and so back into for.

Replace Cap/Nut into Fork Tube with Socket Wrench and Extender.

Replace Handles and Moirrors and Nut holding both of these.

Replace back onto bike the Front Wheel

Check Brake Calipers for leaks and Pad Wear. It's Very Cheap to get new Pads. Not cheap to have months off work after a crash.

Replace back onto bike Calipers.

Pushing Bike (Not ride) test Brakes and Suspension.

At This point I am thinking your done. You may need to Add Air Preload into the Fork via the Air Valve. 4PSI is a Starting Point. I have run upto 15psi. Without Air in the Preload you may find it too soft. Upto you.


Did I Forget Anything?


Sep 11, 2009 | 1992 kawasaki GT 750

3 Answers

How do I change the fork seals on a 2008 Honda CRF 250 r? Do I use a special tool? Oil? How much oil? Thanks so much for your expertise. Do I put equal amounts of oil on each side? Inner tube- outer tube?


hi,replacing the seal is quite easy,although it will sound complicated,jack up or lift the bike off the ground so that the front wheel is in the air(about 12-14 inches should be enough,remove the front wheel from the bike,remove each fork leg,this is done by undoing the bolts(4 on each leg)the front fork is quite easy to work on just do one at a time,remove the dust cover from the top of the staunchion tube(larger diameter tube),beneath that dust cover you should see a retaining clip that holds the seal in place,remove the retaining clip(and dont lose it),the seal is now ready to remove,the easiest way that i know to do this is to force a screwdriver through the body of the seal,you may need to hit the screwdriver with a hammer as some seal have a tin backing plate,put a hole through the seal on each side of the fork leg taking care not to damage the chrome of the fork leg,then use the screwdriver to lever the seal out of the fork leg,to reinstall the new seal,put a smear of grease or oil around the outside of the new seal,slide the new seal down the fork leg and seat it squarely into the fork tube,very carefully tap the new seal into place being very carefull not to damage the outer surface,i use a small piece of dowell type timber to do this as the wood doesnt damage the seal surface,i use a small ballpeen hammer to tap the wooden dowell,once you have the seal seated down the tube you should be able to see the groove for the retaining clip,reinstall the retaining clip making sure it is seated corectly,replace the dust cover,if you are going to replce the fork oil or top it up do this once the fork leg is back in the bike,repeat the whole procedure for the other fork leg,once you have done the fork seals reinslall the fork legs back into the bike and refit the front wheel,to top up the oil in each leg,simply undo the large cap on the end of the fork leg,you may have to remove the handlebars to do this,be carefull as the cap will be spring loaded and can easily fly off if you are not ready for it,top up or fill with the correct weight oil for your bike(normally a 10w oil),check with your local honda agent for the correct quantity,normally between 400-500 mls,this all sounds quite complicated but is actually quite easy and can be done with a minimal of tools,each fork shold take about 1/2 hr to do...hope this is a help to you

Jul 15, 2009 | 2005 Honda CRF 250 R

1 Answer

Seals blown on front shocks


to remove seals you will need to remove each fork leg from the bike,i put the bike on the centre stand and jack under the motor to get the front wheel off the ground,after you remove the fork leg,remove the dust cover(if fitted),remove the circlip holding the old seal,you may have to stab through the old seal with a screwdriver to remove the seal from inside the leg(be carefull not to damage the chrome on the fork leg),clean around the surfaces and install the new seal making sure it goes back in dead square,refit the circlip,then refit the dust cover,replace fork tube back in bike and top up with new oil,most bikes take between 300 to 500cc of oil,but check with your local shop as all bikes are different,and you can adjust the amount of rebound damping by varying the amount of oil you put back in,..sounds complicated but quite an easy job..hope this helps

Jul 04, 2009 | 1995 Suzuki GS 500 E

2 Answers

How to fill the front suspension on a ktm exc 2001


If you get the sevice manual or contact a dealer to get the correct oil amount for your bike, they need to know the model and year, you have to have the forks off the bike. take the fork caps off, take the springs out compress the upper fork tube all the way and add the specified oil. if they also give you the measured amount from the top that's the best way to get both fork oil levels exact. there is a special tool that you set the oil level in millimeters and it sucks out the oil to the right level, but before you do that step after adding the oil always pull and push on the cartage rod several times to remove air from the cartage tube. you will hear the air coming out and you will feel the changes in the cartage rod as the cartage tube fills up with oil and the air is removed.
something i'm confussed on though is if you replaced a seal you would have had to brake down the fork to replace it. you would have poored the oil into a container, cleaned all the internal parts,and used a fork seal driver to install the new seal. part of your question asks where do i put the oil in? thats in the open end of the fork after you have taken off the fork cap. It sounds to me like you only replaced the dust seal on one fork. that is not going to fix your leaking fork. you need to replace the oil seal thats pressed inside of the top fork tube.

Dec 01, 2008 | 2008 KTM 200 EXC

Not finding what you are looking for?
2002 Honda CR 250 R Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...