Question about 1999 Honda GL 1500 SE Gold Wing

1 Answer

Cluch will not engage when I pull in the cluch lever

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,978 Answers

Make sure the clutch master cylinder is full and bleed the system at the clutch slave cylinder. This should make it work again. If there is leakage at the lever or slave cylinder , Buy the master cylinder kit and the slave o-rings and replace the seals. Bleed the system and you should be good for another ten years.

Posted on Aug 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air conditioner electric circuit


Try disconnecting battery for two minutes to reset the system. Then start the car and check a/c operation.

Dec 22, 2013 | Oldsmobile Cars & Trucks

1 Answer

Honda vt1100


You can try adjusting couch cable to specs. If that don't do it you may have to adjust cluch throw out bearing, to specs.

Aug 10, 2017 | Motorcycles

1 Answer

Loose cluch pedal 1999 gmc sonoma sl how to fix


ADJUST IT, STUDY HOW IT WORKS, WHY ITS LOOSE, USE COMMON SENCE, GET UNDERNEATH AND MAKE IT HAPPEN ! GO FOR IT

Mar 16, 2013 | 1999 GMC Sonoma

1 Answer

How to replace the cluch return spring


Transmission has to be taken out of vehicle

Nov 29, 2012 | 1996 Nissan Pickup

1 Answer

Cluch seems to engage to high on release


if it's hydralic? it may need replacing. Some (push rod) clutches can be adjusted..on (Z-Bar) cluch type..check the Z-Bar to see if it is cracked or bent

Aug 01, 2012 | Corgi Classics James Bond BMW Z3

1 Answer

Hi i have just got a 05 cr 125 and when i select a gear withe the cluch pulled in the bike stalls like the cluch is sticking or not operating but can feel resistance in the leaver and can hear it operating...


Hi, sounds like you may have too much free play on your lever, when you pull the clutch it is not disengaging all the way, try taking some free play out, simply turn the adjuster at the lever so when you pull the lever it has resistance after half inch, if is is still the same than wrong oil can also do it, worn clutches is another reason.

Feb 14, 2011 | 2002 Honda CR 125 R

1 Answer

Drive problem


check your cluch cable it may be sticking up also check you have free play on this cable,, put the bike on its center stand and spin the rear wheel with the bike in gear holding the cluch in as you spin the wheel if it spins ok the cluch is letting go

Jan 23, 2010 | 2007 kawasaki ZX-6R

1 Answer

2000 blaster i installed a new cluch cable and looks like its working i adjusted at the cluch lever still not working.


mind do not tighten the cable there must be play in the lever. if the bike is winning and not moveing its the cluch plates.

Jan 16, 2010 | 2003 Yamaha YZ 125

1 Answer

HELP the cluch on my 1993 VW golf is haveing problmes


From what I am gathering. the pedal and cable assemblys are ok. then it is time to tear into the clutch its self. Sounds like the throwout bearing is bad.

Jan 29, 2009 | 1999 Volkswagen Golf

2 Answers

Chain is not moving, with engine running; it was working fine but then stopped. The chain oil tank was empty or thereabouts when I looked into it although when I opened the chain guard cover oil, was...


ARE YOU SURE THE KICK BACK BAR IS NOT ENGAGED , IF YOU HAVE PULLED IT BACK VIGOROUSLY AND STILL HAVE PROBLEM IT IS PROBABLY NOT ENGAGED , THEN THE NEXT BEST CK IS TO REMOVE THE BAR AND COVER ,LAY DOWN AS IT CAME OFF SO NO MIX UP IN RE-INSTALL WITH IT OFF SEE IF THE DRIVE GEAR IS TURNING IF SO PROBLEM COULD BE IN BAR , YOU MIGHT ALSO TRY TO LOOSEN THE CHAIN UP A WEE BIT AND SEE IF THIS HELPS , REMEMBER WEAR SAFETY GLASSES AND GLOVES AND STAY CLEAR OF ALL MOVING PARTS

Jan 12, 2009 | Husqvarna Chain Saw 20" Bar

Not finding what you are looking for?
1999 Honda GL 1500 SE Gold Wing Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...