Question about kawasaki ZZR 400 Motorcycles

1 Answer

I need a rear brake disk and pads, also a Thermostat for my ZZR400 Grey Import, I believe it is in a 600 frame, dated manufactured 1991 (delared).

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Smoke From Left Rear Wheel


Could be oil leaking onto the brake pads or shoes.

Jun 20, 2013 | 1991 Chevrolet S-10 Blazer

1 Answer

I'm trying to understand the VIN for my 1998 Mitsubishi Pajero. I thought that the VIN is supposed to be seventeen characters, but the chassis code shows less. Here is what I have...


You are kind of correct, but you're not if it's a grey import.

All vehicles manufactured for the European market, regardless of where they are produced and what manufacturer made them, will, without exception, have a VIN that is 17 characters long. These include a World identifier at the beginning, usually three characters in length, that denotes the country where the vehicle was manufactured.

If your Pajero is an import (and presuming you are in the UK, it is, or it would be badged "Shogun" not "Pajero"), the VIN will have fewer than 17 characters.

Additionally, on an import, the World Identifier will always be omitted and they will often, but not always begin wih the model type.

For example:
Shogun - JMAL049GWJJ000001 (UK)
Pajero - L049-000001 (Janpese import)
To cunfuse the matter further, somewhere in the number you have is a date code, but since the manufacture date in Japan is not based on the gregorian calendar, but on the number of years since the most recent emporer ascended the throne..... good luck with that!

I've been scouring a number of sites I would usually use to answer your question in more detail and all I can tell you is that it's a nightmare and nowhere can I find a site that can even tell me how many digits to expect on your japanese import, let alone their meaning. Even grey importers who bring these things in seem to struggle with figuring out what they mean!

Jul 22, 2011 | Mitsubishi Pickup Cars & Trucks

1 Answer

My back brake is sticking on i no me brack pads are low but is there any way to free them


You need to take the master cylinder apart and clean it . There is a small pin hole that is plugged with dirt or rust. Or rear you have a really dirty rear caliper that is not floating properly. A pressure wash should fix that.

Sep 03, 2010 | 1991 Yamaha FZR 600

2 Answers

Hi, i´m looking for a new rear brake disc for my Gilera RC 600C (93), still couldn´t find a dealer, any help is apreciated..thanks .


Try www.cmpo.co.uk or www.chinesemotorcyclepartsonline.co.uk (same company) I'm pretty sure that they will be able to help you as they stock parts for pretty much all import bikes. They are a massive company based in exeter, UK.

Aug 27, 2010 | 1991 Gilera RC 600 R

1 Answer

Is it very difficult to replace rear brake pads on a honda vtx 1300r


Personally I have never replaced pads on that particular bike but if it is like most rear disk pads, should not be too bad. I just remove the 2 bolts holding the caliper to the frame. Lift the caliper off enough to slide the pads out. Get a small C-clamp or something so you can gently push the caliper piston back in. Then install the new pads and bolt the caliper back on. Be carefull when pressing the piston back in because is might cause your master cylinder to overflow a bit. Once the pads are on the bike, pump the brake a few times until the pedal gets firm. Should be no need to bleed the system as long as you don't open any brake lines.
Hope this helps!

Aug 26, 2010 | 2005 Honda VTX 1300 R

1 Answer

I have no brakes, disk brakes on front, drums on back


if you have no idea here what to do,you need to take your truck to a shop for repairs

Jan 07, 2010 | 1991 Dodge Dakota

1 Answer

Rear Brakes


First open the fluid tank and put a cloth around it not to spill any fluids.Push the rear caliper slowly and strongly against the disk rotor so that the caliper's piston go all the way in.If the fluids overflow the tank remove some.Unscrew the pin's plug at the rear end of the caliper with a flat screwdriver.Inside there is the pin's head witch is a 5mm allen bolt.Unscrew the pin and work backwards installing the new brake pads.After tightening the pin (18Nm) and the plug (12Nm), push the brake pedal many times until it's fully engaging the brake.Then add some brake fluid to the tank until it reaches the "max" mark and close it.And you're done.

Jun 27, 2009 | 2000 Honda CBR 600 F(4)Y

1 Answer

How do I replace brake pads on real wheel of CBR 600F 1996


the problem is probably 2 things in the brake.
one the pads could be worn and two the disk is probably wearing in a wavey fashion.
run you hand over the disk surface and see if it feels lumpy, if so have it surfaced when you replace your pads.

Jun 07, 2009 | 1996 Honda CBR 600 F(3)T

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...