Question about Factory bike Chrono SM 250 Motorcycles

1 Answer

My Chinese 250 CC scooter has 480 miles on it. It has run great. I had it for 2 years. Kept it stored in a dry shed. I tried to start it as usual. This time the battery was kind of run down. After cranking a couple of times it started and run ruff for about 10 seconds and stalled. So I put a chanrger on it. Trying to start it again it wound not even sputter. Wouldn't even fire at all. It was only a few minutes between tries. The next day it still would not even sputter.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 327 Answers

Pull the spark plug and crank it and check for spark if it has spark spray a little starting fluid in carb and it should sputter if it does the carb is gummed up the needle is stuck in the seat remove carb take the screws that hold on the fuel bowl out you will see the float wiggle it up and down slowly you will see the needle not moving slide the pin out that holds in the float you gotta tap it out with something small like a small punch or a nail spray the needle with carb cleaner only to soften the gummed up buildup and wiggle up the needle and float clean it all with carb cleaner and reassemble it should start now hope this helps

Posted on Aug 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Sym moped starts but won't idle It shuts off when trying to give it gas


Hi, Gigi and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Float needle and seat sticking.
5. Float level too low.
6. Carburetor bowl vent line clogged/blocked/pinched.
7. Idle adjusting screw set too low.
8. Air/fuel mixture screw set too lean.
9. Idle port, transfer ports, slow air jet clogged.
10. Slow fuel jet clogged.
11. Faulty fuel pump.
For more information about your issue and valuable "Free" downloads that you will need please Click on the links below. Good luck and have a nice day.
Scooter Questions Get Answers to Your Scooter Starting Question
Scooter Troubleshooting Scooter won run All about Scooters
My chinese scooter wont idle or start Check the fuel petcock
http://scooterunderground.ca/knowledge/manuals/documents/sym_fiddleii125_service_manual.pdf

Oct 01, 2016 | Sym 125 EXC SIXDAyS Motorcycles

1 Answer

2005 people 50 2 stroke. Why won't it start?


My scooter has no spark how to fix. gy6 chinese ... - YouTube

? 2:29
https://www.youtube.com/watch?v=UU4S0Ov9q4c
Aug 24, 2012 - Uploaded by Rolling Wrench
Purchase our "NO SPARK KIT" click the link below: ... My scooter has no spark how to fix. gy6 chinese scooter 139qmb qmb13950cc 150cc.

Author Topic: people 50 2 stroke no spark CDI?? - KymcoForum.com

www.kymcoforum.com > Scooters - 50cc > People 50
Aug 5, 2012 - 7 posts - ‎4 authors I have a 2001 people 50 2 stroke that only has 125 original miles. ... I ordered a CDI and coil from monster parts and it still would not start . Author Topic: (Almost) no spark / engine not ...
15 posts
Aug 15, 2011
Kymco People 50 - Not A Morning Scooter ...
15 posts
Sep 28, 2010
Author Topic: 2005 People 50 2T Mods ...
15 posts
Jul 27, 2010
Kymco People 50 - KymcoForum.com
10 posts
Nov 15, 2008
More results from www.kymcoforum.com

Nov 03, 2015 | Kymco Motorcycles

1 Answer

Jincheng scooter issue


sounds to me that your belt is slipping
try changing your belt
different manufacturers all have different prices
but most Chinese scooters all have the same gy engine and drive gear
so shop around and find the cheapest

Apr 04, 2014 | Motorcycles

1 Answer

My benelli velvet 250 is using to much fuel


Hi Anonymous and the usual suspects are:
1. Excessive enrichner use.
2. High-speed riding style.
3. Idle speed improperly adjusted.
4. Dirty air cleaner element (may also affect idle speed).
5. Vacuum piston assembly malfunction.
6. Excessive accelerator pump output.
7. Plugged or restricted bowl vent.
8. Fuel level too high.
9. Loose jets.
10. Worn or damaged needle or needle jet.
11. Enrichner valves not seated or leaking.
12. Plugged air jets or passages.
For more information about your issue please visit the websites below. Good luck and have a nice day.
Scooter Carburetor Idle Adjust
Vespa Air Filter Cleaning How to
How to rebuild your Chinese scooter carburetor
Benelli Velvet 250 Service Manual downloadallfileshere com
benelli velvet



Mar 04, 2013 | 2010 Benelli Velvet 250

1 Answer

Diamo 2006 Cruiser VTwin 250 oil change


Hi, Willie try using a breaker bar or a 2 ft. long piece of pipe that fits over your ratchet handle for more leverage and give it a quick snap for more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
Hyosung GV250 Service Oil Change
http://www.carlsalter.com/diamo-service-manuals.asp
Scooter Parts for Chinese Scooters Atvs
Chinese ATV Owners Repair Manuals
Diamo Cruiser Twin 250 2006

Jun 08, 2012 | 2006 Diamo Cruiser VTwin 250

1 Answer

Just bought 2 diamo retro scooters each with around 250 miles on them and the owner said the batteries were dead but besides that they were fine. They had not been ran in over a year however, now my...


Hi, Atlas_cantre if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will idle and run poorly, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition.
1. If your battery was 3 years or older when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a volt meter, you should have 12.5 volts or better, any readings in the 11 volt range you need to do a proper load test on the battery and replace as necessary, any readings in the 10 volt range you have a dead cell and replace the battery.
4. Drain and flush fuel tank, google " how to clean a motorcycle gas tank" find a couple forums to view the different options available.
5. Remove your air cleaner and clean and re-oil per Mfg. specifications.
6. Remove the carburetor, disassemble and decontaminate with a carb dip or if you have EFI remove injectors and clean with carb spray and compressed air
7. Remove fuel valve and filter disassemble and clean as necessary, remove fuel lines and replace with new ones.
8. Replace spark plug with a new one and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
TROUBLE SHOOTING
http://www.linnbenton.edu/auto/perform/no_start.html
http://www.carlsalter.com/diamo-service-manuals.asp
http://scmotorized.com/image/data/pdf/scooter-repair-manuals/Retro-150--Parts-Catalog-V.12.07.pdf
Chinese ATV Owners Repair Manuals

Jun 20, 2011 | 2007 Diamo Retro 50

2 Answers

I bought a second hand go-ped, there is no indication of any brand, anything, I need to buy some spare parts, but do know the displacement- probably it is midi goped 41, the spark plug is BM6A. How...


Go-Ped or GoPed is a brand of powered scooter and if it is a Go-Ped brand powered scooter then you should find the word "Go-Ped" on it somewhere. I think on average a Go-Ped will have the Go-Ped brand on it in about 17 different places and would seem unlikely that that all the labels are removed.

Jan 30, 2011 | Go Ped Toys

2 Answers

Direct bikes scooter wont start


you need to have some fuel in the system over night as when it is shipped it is completly dry when this is done it should start with out any problems if it still has the same problem then you will need to charge the battrie

Nov 02, 2009 | 2004 Factory bike Chrono SM 250

1 Answer

Scooter will not start


I had the same problem. the drain hose on the carb is supposed to have a little valve in it. it is meant to drain your carb when you winterize, HOWEVER, they fall off and fuel runs out. Screw a small bolt into the end of the hose and bingo- it runs.

Jul 01, 2009 | Sport & Outdoor - Others

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Factory bike Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

john h

Level 3 Expert

12104 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Are you a Factory bike Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...