Question about 2005 Honda Eterno

1 Answer

Seat lock inner wire removed from its position.resulting we can not open seat cover for refilling petrol ect. please help as we have not any eterno service mechanic near by.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 252 Answers

Hi

When you put the key in, push the seat down very hard when you do it, then pull up. This pushes the striker hoop onto the lock, but as you are unlocking it, it should pop it up.

If this does not work, get a long screwdriver and lift the seat up, pushing the screwdriver into the locking mechanism. (again have a friend unlock the seat using the key) and force the screwdriver into the locking part. Once you get the seat up, place a metal rod across the lock. Then find the cable and refit it as necessary

Hope this helps

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 1986 Fiero GT driver side door will not open. It has manual locks. Please help


Remove the cover off the inside and check a rod has not fallen down and jamming the mechanism.

Nov 01, 2014 | 1986 Pontiac Fiero

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

HOW CAN I REMOVE THE PRINT HEAD ASSEMBLY ON A CANON MX340?


Follow the given steps:

1. Confirm that the printer is powered on.

2. Open the paper output tray and top cover.

Note: Gently open the paper output tray while holding it.

3. After confirming that the print head holder has moved to the center, open the inner cover.

4. Remove all ink tanks.

5. Raise the print head lock lever and remove the print head.

6. Re-seat the print head into the print head holder and lower the print head lock lever until a click is heard.

7. Insert the appropriate ink tank into the slot at the right end and push down on the PUSH mark on top of the ink tank until a click is heard. Install the other ink tanks in the same manner.

8. Close the inner cover and top cover.

If you need any technical help on printer then you can reach at http://www.vtechsquad.com/

Nov 12, 2012 | Canon PIXMA MP130 All-In-One InkJet...

1 Answer

00 micra where is drain plug


done it myself so i cannot play indignant of southsea ,showing my age here -points of view joke- right lift the back seat and under the seat is a cover ,now take this cover off and their is the sender unit ,now on the multiplug will be two think and two thin wires ,one of these thick wires is the positive feed and the other is the earth so assume its red and black ,so earth is either a black or a white wire ,now hot wire a direct feed from the battery to the pump feed but first find where it comes up to the injector rail and disconnect it here somehow (varies) then a connect a pipe to this and aim into the recepticale .the connect the pump and in about 4/6 mins the tank will be empty ,disconnect the pump then put 10 litres of petrol in and run pump for a couple of seconds to clear the fuel line or purge it in post technical terms ,reconnect the fuel line and remove the hot wire ,american slang iam learning on here american ,anyway job done .No need to steam clean fuel tank and a i have seen some bills for removing tank ect ect ,what a load of brown stuff from a bull just an excuse to up the bill worst for this is some dodgy cowboy dealers

Apr 02, 2012 | 2001 Nissan Micra

1 Answer

I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Feb 02, 2012 | 2000 Dodge Caravan

1 Answer

My canon pixma ip1300 is showing service error 5100, not printing and yellow light blinks five times thanks in advance..........


Solution: Install the print head and ink tanks correctly iP3000 / i560

Seat the print head Below is the procedure for seating the print head and ink tanks:
  1. Power on the printer.

  2. Open the paper output tray and top cover.

    Note: Gently open the paper output tray while holding it.

  3. After confirming that the print head holder has moved to the center, open the inner cover.

  4. Remove the orange tape securing the print head lock lever, and raise the print head lock lever.

    Note: If the top cover is left open for more than 10 minutes, the print head holder will move to the right. If this occurs, close the top cover once and then re-open it.

  5. Remove the print head from its package and remove the orange protective cap.

    set_print_head_1.jpg

    set_print_head_2.jpg

    <1> Electrical Contacts and Print Head Face's Nozzle Area
    <2> Ink Supply Filters

    Note: To avoid any damage, do not touch the print head face's nozzle area, electrical contacts, and ink supply filters. After removing the protective cap, set the print head into the print head holder immediately. Do not re-attach the protective cap after it has been removed.

  6. Set the print head into the print head holder, and lower the print head lock lever until a click sound is made.

    ip3000_printhead_install.gif

    Next, install the ink tanks.

  7. Remove the cyan ink tank (BCI-6C) from its package. Pull the orange tape in the direction of the arrow to remove the wrap film completely.

    set_print_head_4.jpg

    Note: Remove the orange tape completely. If the orange tape is not completely removed, it may interfere with printing.

    set_print_head_5.jpg

    <1> Removed correctly
    <2> Removed incorrectly

  8. Hold the ink tank as shown in the image below. Twist the orange protective cap in the direction of the arrow, and remove it.

    Note: Remove the protective cap while holding it, so that fingers will not be stained by the ink.


    set_print_head_6.jpg

  9. Insert the ink tank into the slot at the right end, and push down on the PUSH mark on top of the ink tank until a click sound is made. Install the other ink tanks in the same manner.

    ip3000_ink_seat.gif

  10. Close the inner cover and top cover.

    Note: Check that each ink tank is installed in the correct position:



    Properly installed:

    ip3000_tank_seat_correct.jpg

    Improperly installed:

    ip3000_tank_seat_wrong.jpg

    <Left Image> The M ink tank is not fully seated.
    <Right Image> All ink tanks are not fully seated.

Dec 03, 2010 | Canon PIXMA iP1300 Printer

1 Answer

How can I remove the Canon iP3000 ink jet printed heads for cleaning?


heres the support site for that printer http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=257&modelid=10238 - downloads and drivers tab - has all the software and user manuals - the FAQ tab has a section on cleaning the printhead using software - also a link to removing the printhead
The FAQ has full images and step by step instructions Remove the print head iP3000
  1. Confirm that the printer is powered on.
  2. Open the paper output tray and top cover.
  3. Note: Gently open the paper output tray while holding it.
  4. After confirming that the print head holder has moved to the center, open the inner cover. Remove all ink tanks.
  5. Raise the print head lock lever and remove the print head.
  6. Re-seat the print head into the print head holder and lower the print head lock lever until a click is heard.
  7. Insert the appropriate ink tank into the slot at the right end and push down on the PUSH mark on top of the ink tank until a click is heard. Install the other ink tanks in the same manner.
  8. Close the inner cover and top cover.
  9. Note: Check that each ink tank is installed in the correct position.

Apr 10, 2010 | Office Equipment & Supplies

1 Answer

Put in cartridge error


Hi celcono,

Many times this happens because the Print Head needs reseated.

Here are the instructions from Canon on reseating the print head.

Reseat the Print head Reseating the print head is seldomly required to do.
  1. Make sure the machine is powered on.

  2. Lift the Scan Unit until it locks into place (1). The Print Head Holder moves to the center.

  3. Open the Paper Output Tray (2).

    sj402031.jpg

  4. Open the Inner Cover (2). The print head holder (3) should be centered.

    mp130_noprinthead.gif

  5. Lift up the lock lever and take out the print head. The print head can be removed with the ink tanks installed.

    mp390_removeprinthed.gif

  6. Reinsert the print head back in position and press down the lock lever.

    mp390_replaceprinthead.gif

  7. Close the Inner Cover (1) and the Scan Unit (2).

    mp130_scanunitclosed.gif

    CAUTION: Press the center of the Inner Cover until the cover locks into place.

  8. After the Scan Unit is return to its original position, the LCD displays a message asking if you replaced an ink tank.

    sj402033.jpg

  9. Press [+] and select [NO] to exit.
Regards,

-SHG

Dec 25, 2008 | Canon PIXMA MP130 All-In-One InkJet...

1 Answer

Just bought new ink for my printer; Canon MP510 it says it cannot recognize magenta....it is the correct one CLI-8m, it lights up, then I close the cover , it says processing, then it says the following...


Hi, please try reseating the print head.

*Confirm that the printer is powered on.

*Open the paper output tray and top cover.
Note: Gently open the paper output tray while holding it.

*After confirming that the print head holder has moved to the center, open the inner cover.

*Remove all ink tanks.

*Raise the print head lock lever and remove the print head.

*Re-seat the print head into the print head holder and lower the print head lock lever until a click is heard.

*Insert the appropriate ink tank into the slot at the right end and push down on the PUSH mark on top of the ink tank until a click is heard. Install the other ink tanks in the same manner.

*Close the inner cover and top cover.
Note: Check that each ink tank is installed in the correct position.

If issue still present call your printer manufacturer for service.

Tirzo

Jun 12, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
2005 Honda Eterno Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...