Question about Harley Davidson FLSTC - FLSTCI Heritage Classic Motorcycles
Hi Eduardo_hand, and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition or leaking.
3. Spark plug gap to close or to wide.
4. Faulty ignition coil, module and or sensor.
5. Battery nearly discharged.
6. Damaged wire or loose connections at battery terminals especially the ground cable at BOTH ends, ignition coil, or plug between ignition sensor and module.
7. Intermittent short circuit due to damaged wire insulation.
8. Water or dirt in fuel system, carburetor or filter.
9. Fuel tank vent system plugged or carburetor vent line closed off.
10. Carburetor controls misadjusted.
11. Damaged carburetor.
12. Loose or dirty ignition module connector at crankcase.
13. Faulty MAP, CKP, and or CMP sensors.
14. Incorrect valve timing.
15. Weak or broken valve springs.
16. Damage intake or exhaust valve.
For a prime suspect please visit website below and good luck:
Harley Davidson Wiring Diagrams and Schematics
Posted on Jun 10, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Down and dirty way - take it to the dealer and have them install a new tire....
The hard way: place bike on bike jack and remove rear wheel by removing the axle nut and drifting the axle out of the wheel. Derail the belt/chain and drop the wheel out of the brake caliper. Remove valve stem to deflate the tire. Get a set of tire spoons and a 12 pack of COLD brew cause working with tire spoons is no FUN! Pry the bead loose with one spoon and the work your way around the wheel prying the tire beed to the outside of the wheel. Repeat this process for the back side of the tire (in the same direction as the first side so the tire will come off the wheel. Reverse and repeat to install new tire.
By now you will be loading your wheel into the truck and heading to the HD shop. It just really isn't worth the hastle to save the $25 or so to have this job done.
Align wheel with new tire on it with the brake caliper so that you have one shoe on each side of the rotor (you may have to actually remove the caliper if your pads are thick. Install your belt drive/chain drive and then lift the wheel to insert the axle through the swing arm, the chain tensioner and wheel. Reverse
on the other side. Place axle nut on axle and torque to about 80lbs.
Good to go.
Posted on Aug 17, 2009
Set the alarm by holding the key fob button until you see running lights flash twice. Turn off the alarm by pushing the key fob button twice and the lights will flash once.
Posted on Aug 30, 2009
The oil drain us usually a hose with a plug in it that is held by a clip on the frame. It us usually on the right hand side of the bike just behind and underneath the transmission side cover. Loosen the clamp and pull the plug out. The oil will run out of the tank. Replace plug and add new oil to the tank.
Posted on Sep 24, 2009
SOURCE: 2007 Heritage softail
form the sound of it you need a new clutch pak in the starter. Its pretty simply fix. don't let them sell u a new starter just a clutch pak for the starter. I take it by spinning u are not talking about the motor turning over. If its turning over then its not the starter.
Posted on Oct 17, 2009
The fork oil is a very specific job needing a manual and a special tool, I don't want to insult anyones mechanical knowledge but if you have never done it before, best to take somewhere else. Engine oil on the other hand is easy, the drain tube to any softail is on the right side by where the frame meets the swing arm, has somekind of plug in it. Start and run bike for a little while, long enough to get it warm but not hot. Remove fill plug and then remove plug in drain line. Using a peice of cardboard or something put in between filter and frame , directing the oil to your drain pan instead of where ever it goes. Put 1 qt oil back in (after everything is reinstalled) start the bike and make sure the oil light goes out, when it does shut bike off and fill to the point that when it is standing upright you get a little oil on the tip of your finger, over filling may result in loss of oil cap from pressure (been there)
Posted on Feb 16, 2010
Tips for a great answer:
Mar 30, 2014 | 2000 Harley Davidson FLSTC Heritage...
Apr 07, 2013 | 2000 Harley Davidson FLSTC Heritage...
Nov 17, 2012 | 2009 Harley Davidson FLSTC Heritage...
Aug 23, 2012 | 2003 Harley Davidson FXST Softail Standard
Apr 30, 2012 | 2000 Harley Davidson FLSTC Heritage...
Apr 22, 2012 | 2003 Harley Davidson FXSTDI Softail Deuce
Apr 07, 2012 | Harley Davidson FLSTC - FLSTCI Heritage...
May 18, 2010 | 2000 Harley Davidson FLSTC Heritage...
Oct 01, 2009 | 2000 Harley Davidson FLSTC Heritage...
98 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: