Question about 1992 Yamaha FZR 600

1 Answer

Hello! I just purchased a 92 Yamaha FZR 600, and no sooner got it home, and the batttery was dead. Charged it (2 amp 12 volt trickle) ran for a day or so, and killed after the battery drained. Should I just replace the stator? If so, anything I need to know about the job? And also any advice on where to find one would be helpful. Thank you! Marty

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

You can find parts at the website below. I suggest you have a dealer check the charging system. Electrical parts can't be returned. I would hate to see you buy a $435 stator and then find out what was needed was a $75 rectifier/regulator assembly. Please rate my answer. Thanks.
www.babbittsonline.com/pages/parts/viewbybrand/default.aspx

Posted on Aug 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Yamaha FZR 600 will not start


Hi, Leah before testing any electrical component in the Starter Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, especially "AGM" batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
My 1993 Yamaha FZR 600 Won Start
What to do When Your Motorcycle Won Start
Yamaha FZR600 1989 1999 Factory Service Repair Manual PDF Download Manuals... $10 cheap
OEM parts for Yamaha
Yamaha FZR600L Owner Manual

May 17, 2017 | 1993 Yamaha FZR 600

1 Answer

Fuel lines diagram or fuel line route to a 92 yamaha 600


Hi, Anonymous sorry you can't find the first and best tool you ever bought for your Yamaha despair, not for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
yamaha fzr 600 Fuel lines diagram Google Search
1989 FZR 600 fuel lines
https://www.tradebit.com/filedetail.php/269137237-yamaha-fzr600-1989-1999-factory-service-repair-manual
OEM parts for Yamaha
http://www.fzrarchives.com/fzr600/600_manual/1999fzr600r.pdf

Nov 10, 2012 | 1992 Yamaha FZR 600

1 Answer

What type of throttle/throttle cable does my 92 yamaha FZR 600 R neeed?


Hi, Anonymous sorry you can't find the first and best tool you ever bought for your Yamaha despair, not for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
https://www.tradebit.com/filedetail.php/2864660-yamaha-fzr-600-service-repair-manual-pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-fz-owners-manuals
Yamaha FZR 600 1992
Tips and Tricks for Motorcyclists

Aug 09, 2012 | 1992 Yamaha FZR 600

1 Answer

I have a 1996 fzr 600 , it shut off going down the road , went to start bile. But batt was completely dead , pushed it off it ran for about a mile or two n died , bike is not charging at all could this be...


Hi, Jporzio82 in order to check out any main system electrical circuit, you have to start with a fully charged battery 12.5 volts or better, and be able to pass a load test if necessary.
1. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. Check the voltage drop at the battery when you hit the starter button, anything below 9 volts you might have a faulty battery.
3. Check voltage at the battery with the bike running at 3,600 RPM should be 14.3 to 14.7 volts. If you are not getting these numbers, you might have a faulty voltage regulator.
4. Make sure voltage regulator is "GROUNDED" and functioning properly, watch the video below on how to test a voltage regulator.
5. Unplug the connector to the alternator and hook your multimeter leads to the alternator (pin/socket selection does not matter) set the multimeter to AC volts, at an idle the meter should read 16 to 20 volts AC. at 2,000 RPM 32 to 40 AC volts, 3,000 RPM 48 to 60 AC volts. If you are not getting these numbers, you may have a faulty rotor, follow step 6
6. Set the multimeter to OHM'S, connect one lead to the alternator (any pin/socket) and the other to a ground, the meter should read infinity. Connect both leads to the alternator meter should read 0.1 to 0.2 OHM'S. If you are not getting these numbers, you have a bad stator.
7. Check all wiring in the charging circuit for worn or chaffed spots and all wiring connectors in the circuit for corroded, broken, or loose pins/sockets, which is the # 1 offender.
For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
battery not charging The FZR Forum
FZR600 generator charging issues
https://www.tradebit.com/filedetail.php/2864660-yamaha-fzr-600-service-repair-manual-pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-fz-owners-manuals

Apr 04, 2012 | 1995 Yamaha FZR 600

1 Answer

1996 fzr 600 wont start


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter control circuit, relay, or solenoid faulty.
11. Main fuse or circuit breaker may be blown or faulty.
12. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
13. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
96 fzr 600 wont start pleeeze help me
My 1993 Yamaha FZR 600 Won Start
Yamaha FZR 600 Service Manual
OEM parts for Yamaha
http://www.journey.cz/moto/navody/Yamaha%20FZR%20600%201999%20owners%20manual.pdf

Mar 06, 2012 | 1995 Yamaha FZR 600

1 Answer

1991 yamaha fzr 1000 it has sat for 2 years. i bout it as a project bike. i have drained the gas tank and cleaned it. when i try to start it it tries but wont start. i dont know where else to turn or what...


Hi, Rossi_thomas if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will idle and run poorly, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition.
1. If your battery was 2-3 years old when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a volt meter, you should have 12.5 volts or better, any readings in the 11 volt range you need to do a proper load test on the battery and replace as necessary, any readings in the 10 volt range you have a dead cell and replace the battery.
4. Drain and flush fuel tank, google " how to clean a motorcycle gas tank" find a couple forums to view the different options available.
5. Remove your air cleaner and clean and re-oil per Mfg. specifications.
6. Remove the carburetor, disassemble and decontaminate with a carb dip or if you have EFI remove injectors and clean with carb spray and compressed air
7. Remove fuel valve and filter disassemble and clean as necessary, remove fuel lines and replace with new ones.
8. Replace spark plug with a new one and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need please click on the websites below. Good luck and have a nice day.
https://answers.yahoo.com/question/index?qid=20080315213436AALQvHk
FZR Won Start The FZR Forum
http://fzronline.com/wiki/lib/exe/fetch.php?media=ebook_library:fzr1000_service_manual_89_90.pdf
OEM parts for Yamaha
Yamaha FZR 1000 1991 1993 Manual zip

Jul 30, 2011 | 1995 Yamaha FZR 600

2 Answers

When i go to start my 92 yamaha fzr 600 it makes clicking noise


This usually indicates there is not enough power to turn the starter over, so the solenoid just clicks. It sounds like you need the battery to be charged. If this is occuring even after 20 to 30 minutes of riding, either the charging system is not working or the battery is bad (motorcycle batteries typically don't last for more than 3 years, less if they are not kept charged during the non-riding months).

Jun 08, 2011 | Yamaha FZR 600 Motorcycles

1 Answer

I have fzr 600 foxeye but i have not started in over six mouths i have drained the tank put fresh fuel in and fully charger battery fuel pump is working but no fuel flow or fuel pipe is bone dry


Hi, M_dean09 if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will idle and run poorly, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition.
1. If your battery was 2-3 years old when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a volt meter, you should have 12.5 volts or better, any readings in the 11 volt range you need to do a proper load test on the battery and replace as necessary, any readings in the 10 volt range you have a dead cell and replace the battery.
4. Drain and flush fuel tank, google " how to clean a motorcycle gas tank" find a couple forums to view the different options available.
5. Remove your air cleaner and clean and re-oil per Mfg. specifications.
6. Remove the carburetor, disassemble and decontaminate with a carb dip or if you have EFI remove injectors and clean with carb spray and compressed air
7. Remove fuel valve and filter disassemble and clean as necessary, remove fuel lines and replace with new ones.
8. Replace spark plug with a new one and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://en.allexperts.com/q/Motorcycle-Repair-837/98-Yamaha-FZR-600.htm
https://www.tradebit.com/filedetail.php/2864660-yamaha-fzr-600-service-repair-manual-pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-fz-owners-manuals

Aug 27, 2010 | Yamaha FZR 600 Motorcycles

1 Answer

My 91 fzr 600 wont start it started out with a bad connection between the battery n batttery cables so i got a new battery n changed the soilinoid then got it workin cuz my electric start wouldnt work of...


sounds like the battery is not charging. So the problem may be in the alternator\regulator
Recharge the battery with a small charger 1-2 amps.
The battery should read just over 12v when charged
Then try to start it.(push it you have to)
When its running put a volt meter across the battery terminals and it should read 13.5 volts.

Jul 17, 2010 | 1991 Yamaha FZR 600

Not finding what you are looking for?
1992 Yamaha FZR 600 Logo

Related Topics:

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...