Question about 2004 Harley Davidson FLHTC - FLHTCI Electra Glide classic

1 Answer

Help my 2004 eletric glide flht has a huge vibration problem and I have changed all motoe mounts already, any other suggestions?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Your crank may be out of balance. it could be the rod bearings as well. if you have had any major engine work done, you may have fly-wheel issues. the vibration is probably starting in the motor and is being transferred to the motor mounts. Also make sure you have the the bushings properly installed on the mounts which is what is used to aleviate vibration transfer from the motor to the frame.

Posted on Aug 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine developed a bad vibration, can this be the compensator sprocket


I would check all the motor mounts. A loose compensator sprocket would give a knocking noise more than a vibration.

Jun 28, 2014 | 2001 Harley Davidson FLHT Electra Glide...

1 Answer

Headlights and guages quit working at 55 mph on 2000 harley davidson


I would guess it is vibration related and related to a loose or broken wire. More than likely an earth wire.

May 02, 2014 | 2004 Harley Davidson FLHT - FLHTI Electra...

1 Answer

My bike has a very bad vibration when i let the cluch out, the more throdle the more vibration , i have allready change front motor mount ,realiegn motor with back tire, also replaced rear swing are mounts...


I'd have a look at the clutch assembly. Specifically, check the nut that holds the clutch assembly onto the mainshaft. You'll have to take the primary cover off and remove the snap ring from the center of the clutch assembly. The nut is behind the there. It has LEFT HANDED THREADS and torques to 60-80 ft. pounds. If the vibration stops with the clutch pulled in or the tranny in neutral, that's the giveaway. Look for something in that area. It could be the bearing in the inner primary or the bearing inside the final drive gear allowing the clutch assembly to vibrate.

Good Luck
Steve

Sep 04, 2010 | 2004 Harley Davidson FLHT - FLHTI Electra...

1 Answer

Need to take off fairing on 2004 FLHT standard were are mounting points


on the side of the forks, u have to remove the front of the fairing to get to them. there are several torx screws on inside fairing to remove then carefully lift from bike.

Aug 25, 2010 | 2004 Harley Davidson FLHT - FLHTI Electra...

Not finding what you are looking for?
2004 Harley Davidson FLHTC - FLHTCI Electra Glide classic Logo

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...