Question about Bajaj Pulsar 150 Motorcycles

1 Answer

I own a pulsar 150 ug 4.5 2010 model.Sometimes I switch on the ignition,The Gauge checks are OK but the starter doesn't work and the lights also don't work at that time but the bike can be started with kick start.After switching the Ignition ON and OFF fro two-three times everything becomes OK.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Bajaj Master
  • 41,895 Answers

Hi Pardeep_0725 you may need a new ignition switch and, I am sorry you can't find the first and best tool you ever bought for your Bajaj but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.Category Archives Product 4 stroke motor Parts 50cc 70cc 90cc 100cc 110cc 125cc horizontal motor
https://www.tradebit.com/filesharing.php/search/0/bajaj+pulsar+150

Posted on Nov 20, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2336 Answers

SOURCE: No power when I try to start bike, just a click…

Check the battery connections. Remove, clean and reinstall them. You probably had them off doing the wiring and they aren't making a good connection now. Always remove the negative first and install it last.

Posted on Nov 20, 2008

  • 46 Answers

SOURCE: 01SUZUKI KATANA GSX 600F Bad Starter/Relay Switch~that is the ?

If there is a clicking noise when you hit the starter button, then the relay should be fine.
If there is no sound, check the fuses before removing the starter.

Posted on Feb 14, 2009

SOURCE: Self Starter problem with Karizma R (Sep 2007)

Check the fuses too and basically all the wiring, there could be somewhere a loose connection also check the wires at the solenoid switch.

Posted on Apr 21, 2009

ldaala
  • 65 Answers

SOURCE: Kawasaki vulcan 1500 tail light intermittant problem

well i would try the switch and see and if that doesnt work then check the wiring for a loose connection or ground or maybe it could be as ez as checking the light bulb it might be loose in the socket

Posted on May 26, 2009

  • 2 Answers

SOURCE: My Suzuki 750 intruder 1991 does'nt start half the

I had the same problem on my 800 intruder, it turned out the contacts were bad in the clutch switch. Its an easy fix and easy to check. Disconnect the wires running into the housing for your lights and turn signals and bridge the connection. That will "hotwire" the bike telling it the clutch is pulled in, and try starting it. Chances are thats your problem. A simple $12.00 mostly plastic part... two srews on the under side of the housing will drop the switch out of the clutch assembly, you can take it apart and clean the contacts, but being as your bike like mine has some miles on it. It probably wouldn't hurt to replace it.

Posted on Jun 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bike pulsar 150 natural light not working what I do


Hi, Ashok if your headlight is not working, keeps burning out, blinking, or is dim the first thing you need to check is the headlight bulb for damaged filaments then check your light circuit fuse, then check your head light bulb socket ground wire for a clean tight connection, that being said the usual suspects are:
1. Faulty ground or power supply wire to headlight bulb socket.
2. Worn down solder contacts or loose fit of the bulb base in the socket due to vibration.
3. Worn, chaffed, or broken wires in the light circuit.
4. Corroded, broken, or loose pins/sockets in wire connectors.
5. Faulty hi/lo beam switch.
6. Faulty ignition switch.
7. Fuse is good but no continuity on both sides.
8. Faulty wiring between battery positive and headlight bulb socket.
9. Weak charging alternator/generator.
10. Faulty voltage regulator/rectifier ground or overcharging.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Pulsar 150 cc headlight horn Problem
http://www.xbhp.com/talkies/motorcycle-ownership-experiences/4984-bajaj-pulsar-150-all-versions-158.html
How to change pulsar 150 head light bulb part 2
Bajaj Pulsar 150 Maintenance Manual

Aug 03, 2016 | Motorcycles

1 Answer

My pulsar 150 engine is seized due to less oil what to do


Hi, Abhimanyu sorry to hear about your misfortune you will have to disassemble the engine and inspect for damage for more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Bajaj Pulsar 180 Engine Work Required Suggestions Please
http://www.xbhp.com/talkies/general-biking-discussion/25758-when-did-you-motorcyles-engine-seize.html
Bajaj Pulsar 180 DTSi Workshop Manual
Bajaj Pulsar 150 DTS Owner Manual
https://www.speedzz.com/vipar-bajaj-pulsar-150-ug-2-engine-parts.html

Jul 11, 2016 | Bajaj Pulsar 150 Motorcycles

1 Answer

How to repair digital meter in pulsar 150 ug 3 mode


Maybe you just have an oil pressure switch issue? Just replace.

Dec 17, 2014 | 2007 Bajaj Pulsar 150 DTSi

1 Answer

Head light not working I see two brown wires are hanging


Hi, Anonymous if your headlight is not working the first thing to check is the headlight bulb for damaged filaments then check your light circuit fuse, that being said the usual suspects are:
1. Faulty ground or power supply to headlight bulb socket.
2. Faulty hi/lo beam switch.
3. Faulty ignition switch.
4. Fuse is good but no continuity on both sides.
5. Faulty wiring between battery positive and headlight bulb socket.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
Taotao ATM150 Evo scooter headlight troubleshooting and bulb replacement
How To Replace Headlight On Jonway Scooter
DOWNLOAD Bajaj Pulsar DTSi DTS UG 180 Service Repair Workshop Manual...
http://www.marutibajaj.com/pdf/Pulsar%20180%20ug3.pdf
http://ondoc.logand.com/d/1735/pdf

Apr 24, 2014 | 2007 Bajaj Avenger 180 DTSi

1 Answer

Pulcar 150 nagative line are not in bike


Hi, Maheshkum85059 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
http://88.198.249.35/d/Pulsar-150-Workshop-Manual.pdf

Jan 26, 2014 | 2011 Bajaj Pulsar 150

1 Answer

My pulsar 150 dtsi does not self start , when i press the self start switch only relay sound comes but there is no sound of starter motor ,, bike starts with first kick only , so engine is ok ,, bt i have...


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
DOWNLOAD Bajaj Pulsar 180

Dec 12, 2013 | 2005 Bajaj Pulsar 180

1 Answer

2008 Bajaj Pulsar 200 DTSi will not turn over


Hi, Justin before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
What Do Check When My Motorcycle Won Start Honda Shadow Forums Shadow...
What to do When Your Motorcycle Won Start
Pulsar Workshop and Parts Manual Team BHP
Shop At Bajaj Pulsar 200 DTSi Bike Parts And Accessories Online Store...
Bajaj Pulsar 150 DTS User Manual

Aug 18, 2017 | 2008 Bajaj Pulsar 200 DTSi

2 Answers

Does cdi affect ignition in pulsar 150


yes the cdi is most importing.the starter coil supply electricity to cdi then cdi forward electricity to high tension coil,and high tension coil forward the electricity to spark plug,spark plug give more fire to piston.cdi not only supply only electricity,cdi adjust the electricity and control the power.ok?

Sep 13, 2011 | 2005 Bajaj Pulsar 150

1 Answer

Sir , I own a 2005 pulsar 150; from last two weeks mostly on first starting a horrible sound like two gears meshing eachother wit h opposite direction is hearing then engine kill it self. But now the...


dont worry budy its a sound of starter motor pinion gear, coz ur model is of pulsar UG-3 Model n the rotor of starter iof ur model is totally dry in crankcase, this was the reason of making the worst sound while cranking ur engine, jus check the starter motor pinion gear.......

Oct 26, 2010 | 2007 Bajaj Pulsar 150

1 Answer

Self start is not working


Hi, Mayankjoshi1 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
https://www.tradebit.com/filesharing.php/search/0/bajaj+pulsar+150

Apr 28, 2010 | 2007 Bajaj Pulsar 150

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bajaj Experts

sachin sharma
sachin sharma

Level 2 Expert

171 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

chandrakantm

Level 1 Expert

8 Answers

Are you a Bajaj Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...