Question about 2004 Husqvarna CR 250

1 Answer

I cant take the clutch baseket off it"s stuck

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There should be locktite on the splines of the shaft that the basket slides onto, you will have to heat the area around the shaft with a propane torch to release the locktite then the basket should come off

Posted on Aug 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 1995 geo tracker that runs great but I can't put it into any gears someone please help


the 5speed box.
sure, but is the clutch bad or the shift lever. bad.
?
so can you start car in gear with clutch depressed.?
yes, no. (or jerks car body)(
"cant"
does that mean tranny is stuck in netural/
or does it mean the clutch drags and the shifter will not shift in any gear? or grinds>
or cant means the clutch slips in all 5 gears and Reverse.?
or can mean parts 27 bad.

http://www.fixkick.com/tranny/rails.JPG

all the checks are here

http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Apr 03, 2015 | 1995 Geo Tracker

1 Answer

I changed the slave cylinder on my clutch of my TATA 207 and now I cant get any gears, It is stuck in reverse gear. the gears where perfect befor I chnnged the clutch slave cylinder ??


Either the new slave cylinder is faulty or you need to bleed it. Sounds like you aren't getting enough clutch release to get the gears to change. You cant hurt the gears by doing anything to the outside components of the tranny.

Aug 26, 2014 | Cars & Trucks

1 Answer

1993 Honda Accord If a knew clutch kit is installed could da transmission be stuck in gear


only if pressure is on drive line and clutch is not releasing or the transmission is stuck take the shifter out of the top of the trans and realign the gear forks with a bar or something remember scotch the wheels so the car will not roll off and depress the clutch at same time then reinstall shifter if you cant move forks fairly easily something is wrong if you have a fluid clutch release make sure it has fluid in it and no air is trapped in system

Aug 20, 2014 | Cars & Trucks

1 Answer

How do i remove the belts. the clutch is stuck, and needs replaced?


Just slip a sppon handle between the belt and the pully. Push the sppon and and over, the belt will come off.

Aug 13, 2014 | Washing Machines

1 Answer

MY 2003 SUZUKI RM125 THE CLUTCH WONT DIS ENGAGE


It sounds to me like the clutch is stuck. If you hold the clutch in and rev the engine a few times, sometimes it will unstick the clutch.

Jan 01, 2013 | Suzuki RM 125 Motorcycles

1 Answer

Cant get clutch to engage after fiting new cable help please


the clutch may be stuck on. Put the bike in neutral, start the bike, run down the road looking like a fool jumping on and off the bike to kick it into 2nd gear and pumping clutch lever. Clutch should be free.

It might also be worth checking if your pushrod has a ball bearing in the end, I had one on mine, replace the clutch plates and it wouldn't work with the ball bearing in :)

Aug 19, 2012 | Motorcycles

1 Answer

2003 ford transit turbo manual gearbox, stuck in 2nd gear, cant start


does the clutch push normally or is the linkage broken not disengaging clutch, and then does shifter move around or locked and wont move, loose linkage in shifter or gears are jammed inside transmission and something went, if shifter wont move at all then trans is jammed inside and needs repair.

Jun 09, 2012 | Ford Transit Cars & Trucks

1 Answer

Problem on my ktm 450sxf 2007 model inner hub on the clutch


Your hub on the shaft - the nut is too tight. The nut is pushing the hub too far on the shaft and making it a drag. Need to back the nut off and torque it at factory spec. That could be somewhere between and 12-15 lbs. This has happened to someone else I know.

May 26, 2012 | KTM 450 SX-F Motorcycles

1 Answer

Dodge neon clutch problem


is clutch pedal down on floor,if so,could be broken cable or release fork,if its stuck at top its fork or clutch damage,online at alldata.

Sep 23, 2009 | 2001 Ford Windstar

1 Answer

My rodeo is stuck in gear


You will need to get the clutch hydraulic system repaired before the clutch can be successfully disengaged.
Meanwhile, try rocking the vehicle backward/forward while shifting gearlever out of gear to get it into neutral.

Jul 31, 2009 | 1996 Isuzu Rodeo

Not finding what you are looking for?
2004 Husqvarna CR 250 Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

choprboz5

Level 2 Expert

196 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...