Question about 2000 Harley Davidson FLHTCUI Electra Glide Ultra Classic

1 Answer

Need to know the foot pounds for 1996 ultra classic EVO head bolts...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

It's not quite that simple on Evo heads. They torque in a particular pattern in three steps. I cannot send the torque pattern to you via this forum. If you'll contact me directly at wd4ity@bellsouth.net , I'll give you the torque pattern and sequences.

Good Luck
steve

Posted on Aug 21, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NNeed torque specs for 2010 harley ultara classic, front axle nut, front brake calipers, axle nut holder


Front Axle = 60 to 65 foot pounds

Front caliper banjo bolts = 17 to 19 foot pounds

Front Brake disk screws = 16 to 29 foot pounds

Front caliper mounting bolts = 28 to 38 foot pounds

Front axle holder nuts = 132 to 180 inch pounds

Aug 23, 2014 | 2010 Harley Davidson FLHTCUTG Tri Glide...

1 Answer

What is the torque setting on the head bolt for a harley davidson sportster


Cylinder Head Bolt Installation
Factory Method
For each cylinder head, start with head bolt numbered one. In increasing number sequence (1-2-3-4), tighten the head bolt in three stages.
1. Tighten each bolt to 7-9 foot pounds of torque.
2, Tighten each bolt to 12-14 foot pounds of torque.
3. Mark each head bolt and head with aligning marks. Tighten each bolt 1/4 turn (90 degrees).


Cylinder Head Bolt Installation
Torque Wrench Method

For each cylinder head, start with head bolt numbered one. In increasing number sequence (1-2-3-4), tighten the head bolt in four stages.

1. Tighten each bolt to 7-9 foot pounds of torque.

2. Tighten each bolt to 12-15 foot pounds of torque.

3, Tighten each bolt to 22-25 foot pounds of torque.

4, Tighten each bolt to 38-42 foot pounds of torque


headboltsequence.gif

Good luck, i hope this helps.

Aug 06, 2011 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

I have a 1981 yamaha XS400 special and i need to know how tight I torque the crank case halves.


Tighten the 8mm threaded bolts with the 12' or 13mm head bolts, or nuts, between 12 and 16 foot pounds, and the 6 mm bolts with the 10 mm head 6 to 8 foot pounds

Apr 14, 2011 | Yamaha XS 400 Special Motorcycles

1 Answer

Replacing the head on chevy cavalier 2.2 need to know what to torque head bolts


On the first pass, torque the long bolts to 46 foot pounds, short bolts to 43 foot pounds. On the final pass, turn all bolts and additional 1/4 turn.

Mar 23, 2011 | 1998 Chevrolet Cavalier

1 Answer

What are the torque specifications for the heads on sporster


You didn't say what year model. Sometimes the heading at the top of these postings are not correct.

For an Evo Sportster, the head bolts must be torqued in a particular sequence. The head bolts are labeled #1, 2, 3, & 4 in the drawings, not literally. The front head bolts are numbered differently from the rear as well.

You torque the bolts in three steps. The first step, you torque the bolts to 7-9 foot pounds. Then you torque them to 12-14 foot pounds. And finally, you mark each bolt and pull it down an additional 1/4 turn. You must torque the bolts in the following sequence.

On the front head, the #1 bolt is the front bolt on the left side of the cylinder head, then the #2 bolt is the left rear bolt, #3 bolt is the right front, and #4 bolt is the right rear as viewed from the top of the head.

On the rear head, the #1 bolt is the bolt at the left rear, #2 bolt is the bolt at left front, #3 bolt is the bolt at right rear, and #4 bolt is the bolt at right front as viewed from the top.

Do not forget to put the O-rings on the dowels when you put the head gasket on and oil the threads of the studs. Make sure you put a new cylinder base gasket on the bottom of each cylinder as well. Once the torque has been taken off the cylinders, the base gaskets will leak unless they are replaced.

On an Ironhead, the head torque is 60-70 foot pounds tightened in a criss-crossed pattern.

Jan 28, 2010 | 2000 Harley Davidson XL 1200 C Sportster...

1 Answer

Brake caliper torque specs


I'd put a drop of Loctite 242 (med. strenght blue) on the threads of each bolt and torque them to 25 foot pounds.

Oct 23, 2009 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How do i adjust the drive belt on the 03 ultra classic electraglide


Loosin the rear axel bolt and turn the adjustment screw in on both side the same amount on both side's. Then tighten the axel nut back down to what the spec foot pounds that the manuel calls for.

Sep 28, 2009 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Heads


here is the sequence pay close attention to the numbers in the brackets

(8) (5) (9)
(12) (4) (1) (13)
(11) (7) (3) (2) (6) (10)

Note : 12 and 11 are at the vey front of the vehicle:
the torque sequence is as follows
step 1) torque all bolts to 22 foot pounds
step 2) turn bolts as follows
short bolts an additional 55 degrees
medium bolts an aditionl 65 degrees
long bolts an additional 75 degrees

Oct 06, 2008 | 1996 GMC Jimmy

Not finding what you are looking for?
2000 Harley Davidson FLHTCUI Electra Glide Ultra Classic Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...