Question about 1999 kawasaki ZX-7R

1 Answer

Bike will not go into gear without stalling out what do i need to do to the clutch

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 220 Answers

If you have a cable it probably needs adjusting. If it is hydraulic clutch then make sure the reservoir on the handlbar by the clutch is full of fluid and you might have air in the line and have to bleed the clutch slave cylinder as well.

Posted on Aug 24, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My bike wont drive when in gear?


sounds like the clutch is toast though it could be other things assuming its not just stuck ie does the clutch lever return after you press it, if so you could try draining the oil out and pass it through a sieve, if there are bits of friction plate in it then the clutch has definatley disintegrated, if the lever stays in then the push rod may be damaged/stuck or the worm drive may be stuck. does the bike go into gear without pressing the clutch lever or stalling?, if the clutch was slipping prior to it stopping then this is likely a knackered clutch, it could also be the wrong oil in the gearbox or perhaps no oil in the gearbox, does the bike go into gear? does it go through all 6 gears and into neutral? more info is needed and even then without looking its hard to say but my guess would be the clutch is fried

Dec 31, 2016 | Motorcycles

1 Answer

REPLACED CLUTCH ON ZR 550 CLUTCH ENGAGES , BUT WHEN FULLY RELEASED BIKE JUDDERS THEN STALLS OUT . TRY TO ADJUST & GEARS WONT ENGAGE .


So if you raise the revs to say about 4000 rpm and let the clutch out does it stall or judder or both will it engage at all and pull away ?

Mar 07, 2015 | Motorcycles

2 Answers

Stalls when engaging first gear


Check clutch switch may be stuck bike thinks you are putting in gear without pulling clutch

Mar 11, 2014 | Suzuki DR 350 S Motorcycles

1 Answer

Fz8 jerks and stalls when but into first gear


Hi, Anonymous you may need a clutch adjustment for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Bike jerks and dies when place it into first gear as if the clutch is bad
http://www.ducatimonster.org/forums/tech/207041-stalling-neutral-first-gear-03-monster-620-a.html
Yamaha FZ8NA Service Manual
OEM parts for Yamaha
YAMAHA FZ8 Owner Manual

Jul 27, 2012 | 2011 Yamaha FZ8

1 Answer

When i put my 1987 Yamaha Virago in gear, it dies


Yamaha motorcycles of this vintage often have issues with their kickstand switch. This switch can be disabled by clipping the two wires that go into the switch and wiring them together--the kickstand switch is normally closed (letting current flow) when the stand is up; the switch is open when the kickstand is down.
This is more afield than your electrical concerns, but if the clutch plates have bonded together, the bike will stall when you put the bike into gear. The bike will start and idle fine, but basically, you don't have a working clutch, so the bike will stall out when you dump it into gear while at a standstill. You can test for this by starting the bike and having someone push the bike to get up to a little speed, then trying to shift into 2nd gear. If the bike lurches forward before stalling or keeps running, you have a clutch, not an electrical issue.
Folks sometimes get lucky, and working the clutch plates a few times will free up the sticking plates. I have had this problem with a mid-1970s vintage Honda that I don't ride very often. Eventually, the clutch plates free up and the bike is good to ride again.
Good luck!

Mar 09, 2012 | 1988 Yamaha XV 535 Virago DX

1 Answer

Gear box goin in to gear but still like it is in nutural


If you select a gear without pulling clutch in it will grind and stall.
If you are certain the bike is engaging a gear and still seems it is in neutral, your clutch drive is broken.
Alternatively, the gear selecter fork bolts maybe loose behind the sidecover, allowing selector to partially engage only and return to neutral. Try selection thru' higher gears, place bike on a stand and turn back wheel in gear, if gears turn and motor doesn't...it is the clutch. If you cannot select a gear proper with rear wheel turning, your selecter is suspect.
Goodluck, and Cheers.

May 07, 2010 | 2004 Yamaha DT 125 R

2 Answers

Gear problems


now you would have to make sure your clutch is not faulty as if the bike slightly jump while putting it in first gear and cuts off , you most probably have a clutch problem .
this is what you have to try first :
start the bike on while depressing the clutch while in gear and see what happens .
if the bike keeps on running , tension the clutch .
if the bike stall , your clutch could be faulty or your oil could be too ,thick and needs changing .
try this first and let me know how you go

Sep 29, 2009 | 2004 Honda CBR 125 R

1 Answer

1982 Honda 650 nighthawk; jumps and stalls when put into gear.


this may help,it doesnt sound like the clutch is out of adjustment,it sounds like the clutch plates have become stuck together,(this happens quite a bit if the bike has been parked for a while..ie over winter)..to fix it get the bike moving,down a drive way or something..then just bang it into gear,then shift into the highest gear you can by shifting without the clutch,once you have a bit of pace on simply hold the clutch lever in and work the throttle on and off all the while holding the clutch lever in,the clutch should free itself fairly quickly and should be back to normall,a lot of older bikes are good at doing this..hope this helps

Jul 05, 2009 | 1983 Yamaha XJ 650

6 Answers

Stalling problem from neutral to first gear


Hi and welcome to FixYa,

Initially, if the bike will be run without its own battery, the engine will really stall. This is because there will be no consumer for the voltage output other than the ignition system which will clamp down when the engine is revved and the voltage tends to go higher still.

Just a start, do postback how things turned up or should you need additional information. Good luck and Thank you for using FixYa.

Nov 27, 2008 | 1984 Yamaha XS 400 L Maxim

Not finding what you are looking for?
1999 kawasaki ZX-7R Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...