Question about 2004 Suzuki RM 250

1 Answer

Will a 2004 suzuki rm 250 front brake line fit on a 2003 suzuki rm 250

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

The '03 and '04 K1, K2, and K3 models use the SKU# 59480-36E30. The '03 and '04 K4, K5, and K6 models use the SKU# 59480-37F00. Personally, I would take the old hose to a dealer and match it up to a new one. The difference in SKU numbers could be simply the supplier or the finish on the metal fittings. If you want to see what K number your bike is, go to the following site and input the VIN number. NOT THE ENGINE NUMBER.
Please rate my answer. Thanks.
http://www.motoverse.com/tools/vin/kawasaki.asp

Posted on Aug 19, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I fit a SUZUKI RM 250 Engine into a 2000 RM 125 frame?


Hi, Anthony sounds like something I would try when I was a kid but after careful deliberation 4 out 5 Suzuki Gods give this one a thumbs down, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm it's just not worth the time trouble and expense you would be better off getting a used 250 bike. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
swapping rm 250 engine into rm 125 frame Suzuki 2 Stroke
Dirt Rider Magazine
RM125 250 frame
will my 250 motor fit in newer 125 frame Suzuki 2 Stroke

Jul 24, 2016 | Suzuki Motorcycles

1 Answer

Does an 1998 Suzuki RM 125 Engine fit into a 2000 Suzuki RM 125 frame ?


Hi, Anonymous after careful deliberation 4 out 5 Suzuki Gods give this one a thumbs down, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
will my 250 motor fit in newer 125 frame Suzuki 2 Stroke
RM125 250 frame
Dirt Rider Magazine
http://www.vitalmx.com/forums/Moto-Related,20/Suzuki-RM-250-Conversions,1247347

Jul 24, 2016 | Suzuki Motorcycles

1 Answer

How do I adjust the rear brakes on my 2004 rm 250


the only thing that is ajustable on the rear brake is the pedal eight ajustement closed to the master cylinder itself...if there is problem braking you may have inside cup done or air in the circuit due to low level or brake line done.....hope this help!

Feb 11, 2012 | 2004 Suzuki RM 250

1 Answer

There are 2 clips on the lower portion of the front brake caliper.. does anyone have a diagram of the caliper layout from a factory manual for a 2004 rmz 250. i need to figure out how each clip locks...


I believe you mean the clips that keep the brake pads from rattling.
The smaller one of the two, fits into the caliper where the front of the pads slide into the caliper. It goes between the pads and caliper, and has a slot to where the disc fits. It kinda fits into a recessed rectangle hole. (Opposite the brake pad pin.)
The longer clip has two small tabs on it's back, near the center, that clips towards the top center of the caliper, and it puts pressure downward on the pads. One end rests on the top of the pads, as the other ends up resting on the "pin" that holds the pads in place.
Look close, and you should see marks where they were, as they can only go on one correct way.
Good luck!

Oct 08, 2010 | 2004 Suzuki RM 250

2 Answers

What is the spec for oil in the front forks on a 2004 suzuki rm 250


If you have the stock valving, I would run 2.5w Motorex in the damper to compensate for the stiff feel stock, and thicker oil in the spring chamber such as Mobil1 5w20 to allow the oil lock ring to do its job on bottom-outs. I'm at 375ml in the spring chamber and I weight 155lb.

Aug 20, 2010 | 2004 Suzuki RM 250

1 Answer

What are the best front rear sprocket RM 250 2002


Hi Gapanzicia, for more information about your question please visit the website below. Good luck and have a nice day.
Rmx 250 Suzuki 2 Stroke
2002 Suzuki Motorcycle Service Repair Workshop Manuals

May 05, 2010 | 2003 Suzuki RM 250

1 Answer

Axle pin wrecked


2001- 2006 rm125 and 2001- 2006 rm and rmz 250 about $50.00 for new,should find a used one on ebay

Apr 06, 2010 | 2004 Suzuki RM 125

1 Answer

How much oil needed in showa front forksfour a suzuki rm 250 2003 or 2004


210 mm from the top of the leg with the fork fully compressed and the springs removed. That's 8.25 inches

Aug 29, 2009 | 2004 Suzuki RM 250

Not finding what you are looking for?
2004 Suzuki RM 250 Logo

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...