Question about 2003 Yamaha Road Star Silverado

1 Answer

Looking for the intake manifold gasket. - 2003 Yamaha Road Star Silverado

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix oil leaks in chevy ss impala 1996



Instructions

1. Removal

Unscrew the bolt that holds the negative connection to the Impala's battery. Set this bolt aside for later use.

Remove the engine cover to access the intake manifold and manifold gasket. Disconnect the throttle body inlet duct from the engine.

Twist off the radiator cap to allow draining of the coolant to flow more smoothly. Place an empty container beneath the radiator's drain plug, and remove this plug. Allow all of the engine coolant to drain into the empty container. Replace the drain plug once you are finished.

Tag all of the electrical wiring and hoses before removing so that reconnection is precise to factory settings. Remove these parts, individually, from the intake manifold.

Loosen the bolts that hold the intake manifold to the Impala's engine block. Lift the intake manifold from the block once all bolts have been completely removed.

Use the flat-head screwdriver to pry the old intake manifold gasket from the engine block. Discard this part once you have removed it.

Clean the engine block thoroughly with the engine degreaser and linen cloth. If necessary, use a gasket scraper to remove excess buildup and grime.

2. Installation

  • Coat the top and bottom of the new intake manifold gasket with a chemical sealer so that it bonds to the engine block securely. Position this new manifold gasket so that it lines up perfectly with the cylinder ports of the Impala's engine block.

Place the old intake manifold on top of the newly-installed manifold gasket until it aligns with all of the holes of the cylinder flanges and manifold gasket.

Attach all of the bolts with your hand to the manifold. Once all bolts have been positioned, use a torque wrench and apply 15 foot-pounds of pressure to the bolts to secure the manifold into place.

Reconnect all of the necessary hoses and electrical wiring to the intake. Pour the engine coolant back into the radiator.

Reattach the engine cover on top of the intake manifold and engine block. Start the Impala's engine and check for any leaks around the new intake manifold gasket.

Jul 08, 2012 | 1996 Chevrolet Impala SS

2 Answers

How to replace a intake plenum gasket


Well basically, you remove the intake plenum and replace the gasket and reinstall the plenum. Here are the steps:

1. Disconnect the negative battery cable from the remote jumper terminal located at the right strut tower.
2. Remove the air inlet resonator and tube.
3. Remove the throttle actuator cables from the throttle arm and bracket.
4. Disconnect Secondary Runner Valve (SRV), Manifold Tuning Valve (MTV), Throttle Position Sensor (TPS), Idle Air Control (IAC) motor electrical connectors.
5. Remove the electrical connector and the Intake Air Temperature/Manifold Absolute Pressure (TMAP) sensor.
6. Disconnect vacuum hoses from the Secondary Runner Valve (SRV) reservoir, Speed Control reservoir, and PCV.
7. Remove right and left intake manifold supports.
8. Remove support brackets at the intake manifold front corners and MTV.
9. Loosen upper fastener attaching throttle body to support bracket.
10. Remove clips attaching EGR tubes to intake manifold.
11. Remove intake manifold bolts and manifold
12. Remove old gaskets, Clean gasket surfaces, and install new gaskets.
13. Reverse steps to reinstall manifold

Jun 16, 2012 | 1999 Chrysler 300M

1 Answer

When I accelerate my grand am makes a whistling noise. It sounds like a turbo. The fast I go the more high pitched it gets.


Its probably an intake manifold leak or a dry belt. check the dry belt by physically looking at the belt at look for cracks or and wobbling pulley. Try adding a lubricant to the belt to see if the noise goes away. If it does get the accessory belt or pully replaced. also check the leak by spraying brake cleaner (or another aerosol cleaner) around the manifold edge (where the intake manifold meets the block and where the gasket is) to see if the noise goes away. If it does then you need a new intake manifold gasket which should be taken to the shop to be replaced.

May 03, 2011 | 2004 Pontiac Grand Am

2 Answers

It is leaking oil from right under the intake manifold is that a gasket leak and how much for part approx.?


From what your describing it sounds like a blown intake gasket, the gasket itself costs under $30 if you are doing this yourself. Be sure to get the manifold gasket and not the plenum gasket too

Mar 03, 2011 | 2004 Chrysler Pacifica

1 Answer

Inlet manifold gasket what does it look like


I gave you the pictures of the intake manifold gaskets for both the 4 cylinder and 6 cylinder for that year. You really won't be able to see them just by looking for them as they will be between your intake manifol and where the intake manifold mounts to the engine but this is what you asked for. I hope this helps and good luck. Here are your pictures


clifford224_115.jpgclifford224_116.jpg

Mar 02, 2011 | 1994 Volkswagen Jetta

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

1996 land rover discovery intake manifold gasket


oil from the pcv valve going into your intake manifold will cause a gasket to swell. but it should not be to the point where it's noticeable. you should probably replace the intake manifold gasket at this point.

Dec 09, 2009 | 1997 Land Rover Discovery

1 Answer

LOOKING FOR THE INTIC GASKET


Intake gasket? It's between the intake manifold and the cylinder head. Takes a decent amount of work to get it out of there. What's wrong with the car to lead you to the gasket being bad?

Dec 05, 2009 | 1995 Geo Prizm

1 Answer

Takes a few turn overs to start


UIM, or LIM

Upper Intake Manifold Gasket,
Lower Intake Manifold Gasket.

If it was that, it isn't because of gas, its because of that damn Dex-Cool Antifreeze.

Mar 20, 2009 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
2003 Yamaha Road Star Silverado Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...