Question about 2000 Husqvarna TE 410

1 Answer

Knocking from engine poss big end is it cheaper to rebuild or replace

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Sorry its not any cheeper either way

Posted on Aug 22, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

It ran out of oil and now it makes loud noises and only runs for 2 minutes. What engine parts might be damaged?


Any moving part relying on lubrication can be affected by lack of oil.

Sounds like the engine is FUBAR!

Apr 09, 2016 | 2001 BMW X5 3.0i

3 Answers

Knock upon throttle


Hi Nick, that's not a lot of information to go on.
My best guess is that if the sound is a thud/knock low in the engine under load you may have at least one worn big end bearing, particularly if this motor is either high mileage or has a poor service and use history.
In a high compression motor this can sometimes be accompanied by a 'tick' sound in the top end, which in non technical terms is Mr piston saying G'day to Mr Valve!
There is no easy fix but in the short term you MAY get some relief using a heavier grade engine oil. If it is the big end it might be diagnosed further by low engine oil pressure, particularly just how fast it drops to zero when you shut the engine down, it should take a second or two not instantaneously. connect a quality oil pressure gauge to check. If it is a big end bearing DONT drive it till it all falls apart as major engine damage WILL result, often a conrod slamming a hole in the engine block which writes off the whole motor.
Big End Bearings can often be replaced by a knowledgeable workshop done in car by just lifting the engine slightly and removing the sump as a cheaper alternative to an out of car rebuild or engine swap..
Good luck
David

Jan 27, 2014 | 1986-1997 Nissan Pickup Side View Mirror

1 Answer

Spun bearing


You are up for an engine rebuild. Remove the engine and turn up side down in a stand. Remove the sump and find the failed bearing by taking off the big end caps. If you find a con rod damaged you will have to remove the head and that piston and replace the con rod. If it is a main bearing that has spun you should only have to replace the crank shaft and fit new bearing shells Either way you will need another crank shaft. Check the price of a low mileage engine from a wrecker as it will be quicker and possible cheaper in the long run

Jun 21, 2013 | Mitsubishi 3000GT Cars & Trucks

1 Answer

I have a loud knocking noise coming from my 3.5l engine on my 2000 intrigue. i am wanting to know what the problem is so i can decide to fix it or not. thanks


a loud knocking normally indicates big end bearings,(about 1/4 engine speed)not a big job but,an engine rebore/rebuild is normally the way to go,its cheaper in the long run.....

Apr 11, 2010 | 2000 Oldsmobile Intrigue

1 Answer

2005 Forester X Engine Knock...big end bearing??? That much???


The lower end of your motor that has the knocking noise will sound like a deep penatrating thud. That will be the rear bearing for the crack shaft. You can find a cheaper place to have it repaired. $3,500 sounds more right to repair at most places

Feb 13, 2010 | 2005 Subaru Forester

1 Answer

Would a faulty speed circuit sensor make the car idol noisy like a rattling knocking noise. noise is louder when accelerating.


NO, it sounds more terminal than that, if you have a knocking sound or noise coming from your engine it could be a few different things, 1. big end bearing, need to rebuild bottom end of engine this is the main one, best get it to a mechanic to clarify the problem for you

Feb 05, 2010 | 2001 Hyundai Santa Fe

2 Answers

Knocking sounds in park and neutral


sounds like transmission internals have failed
best to get overhauled or replaced as change over which could be cheaper and quicker.

Jul 20, 2009 | 1997 Buick LeSabre

2 Answers

Noking


a knock from the bottom of the motor is a big end bearing STOP DRIVING, new engine or rebuild required, a knock from the rear of the engine could be loose pressure plate on clutch assembly, that is if it is a manual, STOP DRIVING. a rattle from top end is lifters or rockers but you say its a knock so probably not it. one test to do, remove all drive belts to water pump etc and start if the knocking is still apparent then it is internal and time to consider trade in, rebuild or new engine.

May 16, 2009 | 2003 Saturn VUE

Not finding what you are looking for?
2000 Husqvarna TE 410 Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

choprboz5

Level 2 Expert

196 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...