Question about 2005 Yamaha TT-R 125 E

1 Answer

Can u replace a spark plug boot without replacing the coil for a ttr125

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Winding it off helps not breaking the wire try that

Posted on Sep 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Stihl fs 80 trimmer, replaced carb, air filter, spark plug, ignition coil. still doesn't start. Next? not getting spark from plug


Loosen coil screws, adjust coil to magneto flywheel magnets with a double sheet of common paper, tighten screws, so that paper will pull out without tearing. That will give you the best chance for a good spark, with all you have done. Pull spark plug out , put top of plug back in spark boot.......crank ovr with rope, and ground spark plug on top of motor(metal), observe the blue spark. If none, check the short wires for any breaks from coil to switch. You can open handle and take out switch, if nothing else works.....then try and start. The wires are just to break the ground, to turn off motor. Can choke motor to stop.

Jul 29, 2016 | Stihl Garden

1 Answer

The porcelain spark plugs keep on cracking when the car is being used


Is the porcelain "cracking" or are they getting "carbon-tracked"? (see example photo of carbon-tracked plug below).
It is common for carbon-tracking to occur if your original plugs were carbon-tracked and you replace the plugs without replacing the wires. If the plug is carbon-tracked, the boots on the wires or the coil boots (coil-on-plug ignition) are also carbon-tracked. If you do not replace the wires or the coil boots, the ignition will still misfire by following the carbon-track on the inside of the boot. This will cause your new plugs to also be carbon-tracked within a short period of time (days or weeks).

There is no reason I can think of for the porcelain itself to actually crack other than faulty installation techniques or possibly, cold liquids getting poured on extremely hot plugs.


5_11_2012_11_40_00_pm.gif

May 11, 2012 | Buick LeSabre Cars & Trucks

1 Answer

Have a honda 11 horse on a north star power washer that has no spark,yes the switch is on.


Cause of no spark can be determined by process of elimination. Good to have a new sparkplug on hand to eliminate plug as fault. So start by replacing plug with new or test plug on mower /edger etc. for spark. If plug ok, then temporarily remove the wire connected to oil alert system (oil alert will ground coil if oil low or dirty). With oil alert unpluged, and no spark suspect sparkplug boot or coil. The sparkplug boot threads on to the spartplug wire and is what actually fits-on to the spark plug. You can test the coil by removing the boot and inserting piece of paperclip wire, or small screw into end of the coil wire and hold close to engine ground while pulling rope. If still no spark suspect coil. If spark, replace the boot. Good luck with repair.

Jul 04, 2011 | Northstar Garden

1 Answer

I got code PO 305 on a 2002 Mercury Grand Marquis, what is the spark plug wire part called, is it #5 coil, and should I replace the coil and spark plug and what should the spark plug be gapped at? Thank...


I got code PO 305 on a 2002 Mercury Grand Marquis, what is the spark plug wire part called
This will have a direct coil over ignition with a coil over each spark plug. The coil is the electrical part over the spark plug. The coil also has a rubber part that is called the boot or spark plug boot. The boots can be purchased separately but the coils will come with new boots.

is it #5 coil,

Have you checked to see if there is any spark coming out of the number 5 coil?



and should I replace the coil and spark plug and what should the spark plug be gapped at?

When was the last time the spark plugs where changed? It may be due for all the spark plugs to be changed. The spark plug gap is usually listed on the emissions sticker under the hood. It should be .050 - .056 or very close to that.

May 16, 2011 | 2002 Mercury Grand Marquis

2 Answers

# 6 misfire while driving start to stutter check engine light flashes then stays on next day light is off and repeat


I am assumming you have a 4.6 V8 in your car. The number six cylinder is on the driverside the second spark plug from the front. These engines have seperate coils for each cylinder and you can remove it by removing the small screw(9/32) that attaches the coil to the engine. Each coil has a boot attached to it that can be removed and replaced or you can buy the coil which comes with the boot or spark plug wire. You may as well replace the plug. You will need a long extension and a spark plug socket to remove it. All you have to do is reverse the procedure. If you have any problem remove the plug once it is loose, just slide the boot from the coil on too the plug and remove the plug with it. Hope this helps leave a comment.

Jul 29, 2010 | Lincoln Navigator Cars & Trucks

2 Answers

How to replace spark plugs on 2000 jeep cherokee classic 6 cyl.? Also does 2000 cherokee have inline fuel filter?


TO REPLACE SPARK PLUGS YOU REMOVE COIL PACK MOUNTING BOLTS THEN REMOVE THE COIL PACK WITH BOOT OVER THE SPARK PLUG.YOU HAVE 6 INDIVIDUAL COIL PACK TO EACH CYLINDER. YOU NEED A 3/8 RATCHET WRENCH - LONG 3/8 EXTENSION -SPARK PLUG SOCKET - SPARK PLUG GAUGE.AND TORQUE WRENCH.THE 2000 MODEL JEEPS FUEL FILTER INSIDE THE TANK.1993 - 1996 MODEL JEEPS FUEL FILTER LOCATED LEFT SIDE OF THE VECHICLE NEAR THE FUEL TANK.

Jul 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Replace spark plugs on a 2008 4 cylinder tribute


This is a fairly easy job. Do each cylinder one by one (removal and install), make sure to reinstall the coil on the same exact cylinder (DO NOT MIX UP). 1. Remove coil retaining scre 2. Pull upward on the coil to remove. 3. Remove spark plug (using a spark plug socket). 4. Properly gap new spark plug (if applicable). 5. Apply sprark plug anti-seize compound on plug threads. 6. Install plug. 7. Aplly coil boot grease on the coils' rubber boot tips. 8. Reinstall coil.

May 22, 2010 | 2008 Mazda Tribute

2 Answers

Replacing spark plugs in a 2002 chevy tahoe


EACH ONE OF THE SPARK PLUGS IS LOCATED UNDER INDIVIDUAL COILS. YOU MUST FIRST REMOVE THE BOLT ON TOP OF THE COIL AND GENTLY TWIST AND PULL UP ON THE COIL WITHOUT RIPPING THE BOOT. UNPLUGGING THE ELECTRICAL CONNECTOR IS NECESSARY ON MOST MODELS. SOME OF THE NEWER MOTORS HAVE A COVER ON THE TOP OF THE ENGINE THAT HIDES THE COILS. PLEASE KEEP ME POSTED. THANKS FOR USING FIX-YA. BEST OF LUCK

Sep 02, 2009 | 2002 Chevrolet Tahoe

1 Answer

Replace spark plugs 2004 dodge intrepid


__________________
Changing Spark Plugs

First off, on this model you don't have plug wires, you have coil packs with a boot and coil connected to the pack. The boot slides on the tops of the spark plug. The good thing about this is that you don't have to mark each wire to its location.

So to replace the plugs you need to disconnect the electrical connector to the coil pack and then unbolt the two bolts that mount the pack down, then remove the pack.

Next with a ratchet, an extension and a special spark plug socket, which has an insulator inside to protect the porcelain from getting cracked, remove the spark plugs.

Next step is to replace the plug, usually I slide off the boot from the coil pack and then remove the coil from inside the boot and slide the boot over the spark plug and start to thread the plug back in. Using this method allows to you feel if you are threading the plug in right. Then with a torque wrench you would torque the spark plug to the specs for the type of engine you have.

3.2/3.5L Engine (20 ft-lbs)
2.7L Engine (13 ft-lbs)

Next reinstall the coil pack with the two mounting bolts, it is only necessary to hand tigthen the two bolts. Then plug back in the electrical connector and continue this process on the next 5 spark plugs.

__________________
Changing Dome Light

To remove the map light bulbs you need to first remove the overhead console.

To do this you need to remove the screw at the front of the overhead console (which is more towards the front windshield).

Next you need to pry down on the rear of the overhead console and then disconnect the electrical connectors.

Then, with the overhead console pulled down, pull of the map light bulbholders and replace the bulbs.

Installation is the reverse of the removal process.

Apr 14, 2009 | 2003 Dodge Intrepid

1 Answer

Changing spark plugs 2004 dodge intrepid


First off, on this model you don't have plug wires, you have coil packs with a boot and coil connected to the pack. The boot slides on the tops of the spark plug. The good thing about this is that you don't have to mark each wire to its location.

So to replace the plugs you need to disconnect the electrical connector to the coil pack and then unbolt the two bolts that mount the pack down, then remove the pack.

Next with a ratchet, an extension and a special spark plug socket, which has an insulator inside to protect the porcelain from getting cracked, remove the spark plugs.

Next step is to replace the plug, usually I slide off the boot from the coil pack and then remove the coil from inside the boot and slide the boot over the spark plug and start to thread the plug back in. Using this method allows to you feel if you are threading the plug in right. Then with a torque wrench you would torque the spark plug to the specs for the type of engine you have.

3.2/3.5L Engine (20 ft-lbs)
2.7L Engine (13 ft-lbs)

Next reinstall the coil pack with the two mounting bolts, it is only necessary to hand tigthen the two bolts. Then plug back in the electrical connector and continue this process on the next 5 spark plugs.

Apr 14, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
2005 Yamaha TT-R 125 E Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...