Question about Suzuki GSX-R 1000 Mladin Replica Motorcycles

1 Answer

Can't get fron brakes to work ,having problem with the bleeding and getting no pressure

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Check ur o rings where hose hooks to caliper and look for any bubbles in hose. Other than that rebuild caliper and or master cylinder.

Posted on Aug 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes my rear brakes not to get enough pressur to bleed them


Because of ABS you can't use the traditional method of bleeding brakes. You have to bleed them by forcing fluid from the bleed nipple up to the master cylinder.

Apr 18, 2016 | Cars & Trucks

2 Answers

I have been working on power brakes and bleed system and got a good pedal pressure


try bleeding the brakes with the engine running there may still be some air in the system. make sure the master cylinder doesn`t run out of brake fluid.

Sep 03, 2014 | 1979 Chevrolet Camaro

2 Answers

After bleeding brakes still have spongy brakes


you still have some air in the lines. go back thru the bleed process again if that doesn't work, get to a power brake bleeder.(amazon about$70) that is a system that puts pressure on top of mc to push fluid thru the system as you open bleed screws. did you know you can adjust brakes by holding down lock button and pumping emergency brake handle. good luck

Jul 02, 2014 | 1998 Toyota Camry

1 Answer

No brake pressure 1996 ford ranger


maybe engine needed to be running while bleeding system?,did you bleed starting from farthest from master then work towards front?,did the vacuum valve at the power booster get disconnected?,

Jan 31, 2014 | Ford Ranger Cars & Trucks

3 Answers

How do I get compression back on my fron t disc brakes after pressing back the cylinder and replacing the brake pads? Ive checked bleeders on all 4 wheels. As well as the master cylinder. Brakes are still...


Just sit in the vehicle and press the brake pedal several times until the pistons in the calipers come in contact and compress the pads against the rotors. Be carefull when first driving after replacing the pads, they wont have full braking effect until they bed down, this can take a few miles of driving to get them working effectively. Safe driving, hope this helps

Mar 04, 2011 | 1999 Chrysler Town & Country

2 Answers

Brake pedal goes to the floor under constant presure. New wheel cylinders, vacuum boost, master cylinder, shoes. Everything bled, and no leaks anywhere. Any thoughts?


DID you bleed in this sequence.... Right rear wheel, left rear wheel, right fron wheel, left fron wheel, ABS hydralic fittings, & finally the Master clyinder? If not you will have air in the lines

Dec 18, 2010 | 1995 Ford F250

1 Answer

Replaced fron rotors and pads on 2006 Jeep Grand Cherokee Refilled brake fluid to minimum level and pumped brakes as required to build ip pressure. However, there is not enough pressure to stop vehicle. ...


Likely you need to PRE BLEED the m/c. Get a kit from parts stores that hook up where brake lines go, and reroute into the m/c reservoir, then do not let m/c run low on fluid during subsequent bleeding, or start over.

Oct 03, 2010 | 2006 Jeep Grand Cherokee

1 Answer

How to bleed fron brakes on 2004 Lincoln Navigator


Bleeding your own brakes is not that difficult as long as you are armed with some good help. I found you a full color pictorial with video that should help. If you have any more questions, please feel free to get in touch. GO HERE FOR PICTORIAL

Sep 12, 2010 | 2004 Lincoln Navigator

1 Answer

Bleeding Brakes


NOt really start at fron driver with resivoir cap off and have another give 3 slow steady pumps on the brakes you tightening the vavle back up in the middle of the third mover yer way around the car...pump brakes well after you are donw wit hall 4, if you changed all 4

May 18, 2009 | 1998 Honda Passport

2 Answers

Brakes are mushy on my 2000 Ford Focus.


i would say your brakes are getting worn out because if the m.c. is low the only reason its low is because your brakes are worn down the fluid doesnt just disappear unless you have a leak just take look and see if anything is wet underneath.

May 11, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...