Question about Suzuki RG 150 Gamma II Motorcycles

1 Answer

I have a problem with a carborator I got always an oilspill. How can I solve it?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

If its an oil leak its coming from the breather meaning a valve problem.
if its gasoline(petrol) (benzine) then its a carborator float or adjustment problem.

Posted on Aug 07, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Choke on carborator is broke


You car always remove the air filter and use your hand trick. meter the air coming in to the carb with you hand to get it started.(Less air hence "choke")

Nov 06, 2013 | Craftsman Sears Snow Thrower Manual Model...

1 Answer

McColloch 7800 generator leaking fuel from the carborator.


rebuild carb using new needle and float if float is full of gas and sinking

Sep 17, 2012 | McCulloch 13HP 338 Cc Portable Generator #...

1 Answer

I have a 99 haley davidson sportster 1200cc and gas leaks from the carburator at a steady pace, why?


tsomething is sticking the float in the float bowl(bottom of carborator) sometimes you can tap on it lightly and it will unstic also may be a bad gasket always turn the petcock to the off position when noy riding

Apr 24, 2011 | Harley Davidson XL 1200 S Sportster Sport...

4 Answers

I need to know where the carborator is on 1998 Saturn SL, with a picture


A 1998 Saturn will not have a carborator as it is fuel injected sorry.

Nov 30, 2010 | 1998 Saturn SL

1 Answer

On a carborator 8 hp B&S engine - how many turns for adjustment Model 195702 - 1-1/2 or 2-1/2 turns?


I always start at 1 1/2 and adjust from there while idleing. Adjust out until it starts if needed. Too lean and will have trouble starting, Hope that helps.

Aug 14, 2010 | Briggs & Stratton Garden

1 Answer

Either need to rebuild carborator or clean it ?


most small lawn mowers have a carborator mounted on the gas tank.
if you take the screws out and look it has a gasket and the gasket will
be bad and need to be replaced also if it is a newwer model it has a
primer bulb that needs to be replaced at same time.

Jun 21, 2010 | Omega Rear Drive Wheel Snapper Mowers

1 Answer

How to calibrate a carborator of shogun


Hi on that model the carbs are ballanced by turning the synchronising screws in between the carburators

May 06, 2010 | 1999 Suzuki GSX-R 600

1 Answer

Smell of gas coming out of exhaust....running rich


If the vehicle is still running original systems then you would need to take it to someone with 1 of the hand programmers to readjust the fuel system settings. If this vehicle has been converted over to or originally was a carborated There are typically 2-4 mixture screws depending on the unit. They will be infront of and behind the carborator. To adjust a carborated you will typically take a flat head screw driver and turn all the way to the right till they are only "finger tight" Once there, note a starting point and from there VIA each screws individual starting point. Turn them all 1 1/2 turns, this will place the carborator at the factory starting position. From there you can then start the vehicle and while it's idleing you can begin to adjust all mixture screws by turning 1/2 a turn till the vehicle looks, sounds, and smells like it is running correctly.

Another method I have seen is using a vaccume pump to register preasure, there are some video's out there to do this method and it can help you fine tune it a little more then one can just by ear. I hope this has helped you or atleast set you in a direction to getting the issue solved.

Apr 09, 2009 | 1986 Chevrolet Camaro

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...