Question about 1997 Honda CBR 900 RR Fireblade

1 Answer

Cbr918 1996 how many turns out for pilet screw for std carbs

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

One and one half turns,

Posted on Aug 06, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install fuel filter in 22" Craftsman mulcher push mower?


if this is a std walk behind mower , the filter is not much more than a screen that's installed in pick up tube inside gas tank this should be just under the carb (carbs on top of tank) , fuel tank removes with just three screws , have a new gasket ready for reinstall of tank as your most likely not going to be able to reuse old one

May 26, 2015 | Garden

1 Answer

Craftsman 16"what is the starting carb adj


Gently turn both carb screws in all the way. Then turn each out one turn. The fast screw is marked with an H and the slow is marked with an L.

Jun 25, 2014 | Craftsman sears 18" Chain Saw Chain (...

1 Answer

Hi, ive got a 1999 g2 kawasaki zx6r been sat for 6 months+. ive changed plugs,battery, petral and pilet jets becoz to blocked, so put like for like back in. it only starts of bump and backfires realy bad...


Have a professional carb service and valves adjustment done.
Just replacing the idle jets will not clean the entire idle circuit. Mixture screws need to be removed, circuit needs to be cleaned out, re-installed,and properly adjusted for idle mixture.
If backfire continues valves need adjusting. Best to do both at same time to save on labor.

Apr 04, 2014 | kawasaki Motorcycles

1 Answer

Backfires


to much air when mixing with fuel in carb find air mixtur screw on carb an whale running turn in slowley till it stops backfiring turning the screw in adjusts the air mixing with fuel the screw is useuly located on the side of the carb witch the toub hooked up to put fuel in carb is
or you could re set it by screwing all the way in then screwing out 3 whole turns then whale running turn out til it back fires then turn screw in haf to three quarters of a turn in hope this helps

Nov 27, 2012 | Motorcycles

1 Answer

Im trying to lite the pilet


This dryer has no pilot light. When you turn dryer on the igniter turns on and lights gas. If yours is not igniting, you could have a bad igniter or a bad heater cavity switch located behind back panel attached to dryer vent area, has two wires connected to it.

Jun 10, 2010 | Estate TGDX640JQ Gas Dryer

1 Answer

Heat will not come on model lgq8000jq3 gas dryer


check and see if pilet is lit, or if automatic check and see if it lights when turned on.

Dec 21, 2009 | Dryers

1 Answer

Bike won't stay running


Drain the carburetors. There should be a screw on the lower side of each CARB float bowl. Remove the screw then replace it after the fuel drains. Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, (not all bikes have a water trap bowl). Install new stock NGK spark plugs.

Remove the CARBS from the bike.
FOR EACH CARB > Remove the float bowl and clean the entire
CARB with a spray CARB cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the CARB. Remove the idle screw and the air screw on the outside throat of the CARB and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the
CARB back together, clean the air filter and install the CARB. Install an in-line fuel filter. Let the float bowl fill then start the engine.

BALANCE THE CARBS
Turn the throttle screw on the LEFT CARB one half turn inward. Now start the engine and get it warmed up. With the engine running, remove the RIGHT spark plug wire. Adjust the idle speed on the left CARB to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.

Now turn the throttle screw on the RIGHT CARB one half turn inward. Restart and rev the engine. Next, remove the LEFT spark plug wire. Adjust the idle speed on the right CARB to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.

SYNCHRONIZE THE CARBS
Remove the air filter and rubber fittings to allow you to see into the throat of both CARBS. You may need a mirror to see inside. You need to be able to see the slides go up and down when you twist the throttle. Now turn the fitting where the cable goes into each CARB such that there is just a bit of slack in the cable, 1/16" is plenty. Lock ONE of the cable adjusters down tight. All further adjustments will be made on the other CARB.

With the motor turned off twist the throttle very slowly while looking at the slides. Both slides need to begin lifting at the exact same moment. If the slides don't raise at the exact same time then slowly twist the throttle until the locked adjuster slide just barely starts to move. Hold the throttle still and turn the adjuster on the other CARB so that the slide on that CARB just barely starts to move also. Now recheck the slide movement timing. Do this process until the slides on both CARBS begin to raise at the EXACT same moment. Lock down the loose adjuster and re-check the slides.

Turn the idle screw on each CARB EXACTLY ONE HALF turn outward and restart the engine. The engine will be probably be idling very fast. Adjust both the idle screws equally from this point to get to the desired idle speed. Congratulations, you have just balanced and synchronized your CARBS This should fix the problem. One last and VERY IMPORTANT thing, Have a fire extinguisher handy and ready for use any time you work on or with he CARBS.

Please rate this solution. Thanks throttlejock!



Apr 22, 2009 | Suzuki GS 500 F Motorcycles

1 Answer

Jet cleaning on a 1988 sportster has ss carb


Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. Set the idle speed with the idle screw. This process should get you back on the road.


Please rate this solution. Thanks!

Apr 01, 2009 | 2000 kawasaki KDX 125

Not finding what you are looking for?
1997 Honda CBR 900 RR Fireblade Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...