Question about Suzuki GSF 600 N Bandit Motorcycles

1 Answer

I have fitted a gsx750f engine to my bandit 600 do i need the cdi for it to run properly?98 bandit and 2000 gsx750f.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Yes you will need the CDI for the 750f and harness as well

Posted on Aug 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi all long story but i put a 1999 gsx750f engine in my 1998 bandit 600 and since then its been overheating give you a rundown i'm using the carbs from the gsx750 but cdi and alternator from bandit 600...


Hi Dave, this information is way above my pay grade your on your own on this one try a shop that specializes in performance mods. Good luck and have a wonderful day.

Apr 04, 2017 | 1997 Suzuki GSF 600 S Bandit

1 Answer

CDI damaged Can i use CDI of Bandit 600 96 model.? thanks


No it won't work, the timing curve is different for one.

Aug 06, 2011 | 1991 Suzuki GSF 250 Bandit

1 Answer

Battery wont retain charge when fitted


the cdi box or equivelant may have short in wiring causing drain and not recharging

Jul 07, 2009 | 1999 Suzuki GSF 600 S Bandit

1 Answer

Will a sump off a 600 bandit fit a 1200


The pumps have different part numbers > The 600 is #16400-06B01 and the 1200 is 16400-06B20
Chances are, even if the pump "fits", the 600 will not have the volume of oil flow needed for the 1200 motor. Starve the 1200 of oil and plan on a new engine in the near future. Sorry.

A “very helpful” rating for this answer? Thanks!

Jun 15, 2009 | 1998 Suzuki GSF 1200 Bandit N

2 Answers

Engine turns over but got no spark


Hi Ash I am Vortash I think I would start at the coil leads then the coil pack and work my way back to the cdi unit checking any fuses that may have blown.. but if you havent got a manual you may find it difficult to identify all the areas that can cause this problem . try this site you may find a manual http://safemanuals.com and I would check for voltage at the coil as this would indicate a blown fuse somewhere on the feed line .. any how good luck Regards Vortash

May 18, 2009 | 1997 Suzuki GSF 600 S Bandit

1 Answer

Bandit 600 starting problems


Sounds like a weak battery. Swap batteries and see if it will start.
Is the kill switch on? Does the side stand have a kill switch? Is it working properly? Is the gas valve on? Got gas? Check fuses. Got spark?

Clean the fuel system
Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. Set the idle speed with the idle screw. This process should get you back on the road.


Please rate this solution. Thanks!

Mar 31, 2009 | 2004 Skyteam ST 125 TR

1 Answer

98 bandit 600 hard to start when engine warm


No not cdi - u r running super rich U need to rebuild carbs

Mar 22, 2009 | 1998 Suzuki GSF 600 N Bandit

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4731 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...