Question about 2006 Gas Gas EC 300

1 Answer

What brand front forks on gas gas 300 ec 2002

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

Go to bike bandit or jc whitney have good seliction and will know the size

Posted on Aug 01, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How i can check what year is my gas gas 300 2003


Jul 25, 2012 | 2001 Gas Gas EC 300

1 Answer

Does it matter which side is down, or should one side be down when splitting the case on a 2002 Gas Gas EC 300? My shifter shaft has broken (spins freely) and I need to split my case to investigate; I...

Hi, you will normaly find that the crankshaft will remove easyer from the r/h mainbearing, thus it will be less difficult to split the cases if you leave everything in the left case, if it is the crankshaft is more loosly fitted in the left case then do it the other way around, gently tapping the shaft ends with a copper or wooden hammer should see them out ok

Aug 29, 2011 | 2002 Gas Gas EC 300

1 Answer

What is the fork oil amount for a 2002 klx 300 per fork tube

The owners manual says to do the following if you don't want to remove the forks:
*raise the front wheel
*remove the fender, meter cable & unit, headlight, handle bar, fork protectors
*loosen the fork upper clamp bolts
*remove the caps from the top of the fork tube
*fully compress the fork tube so the dust cover touches the bottom and place a stand to hold it
*remove the springs
*set the oil level 68mm (standard) or 60 - 90 mm (adjustable) from the top of the tube

It may be easier to remove the tubes and you could replace the leaky seal at the same time. I did this recently and put in new springs too. It was my first time working on forks. With help from TT members and the service manual it was fairly easy. I didn't buy an oil gauge, seal driver, or spring holder. I used a ruler to measure the oil and a medicine dropper to remove any excess. For a seal driver I used a piece of PVC pipe cut in half then secured around the lower tube to drive the seal. Try a search on replacing fork seals for more info. 5w oil is standard but i have heard that 7 works well Good luck.

Dec 20, 2009 | 2002 kawasaki KLX 300 R

1 Answer

It doesnt itck over on idle it keeps cutting out

why dont you turn the idle screw in a few turns on the carb buddy ??f97ca72.jpg

Oct 31, 2009 | 2002 Gas Gas EC 300

1 Answer

Gas gas ec300 vibration

It is normal for a gas gas 300 to vibrate when you rev it its only if there is some metallic sounfds would i be worried.

Sep 10, 2009 | 2006 Gas Gas EC 300

1 Answer

Forks too hard .want to change oil but not sure what grade and how much to use.. what are the basic settings and how do i measure them??

hi mate use 5wt oil and the oil you can do from 80mm-130mm depending on your riding conditions i would do beetween this (105mm) basically take the forks off the clamps unscrew the top drain the old oil out and then you need a 17mm spanner and below the top nut there is a bolt you need to hold this bolt with 17mm spanner then unscrew the top take the top completely off then pull the springs out once done fully extend the forks out as the upper part can slide down then fill up with oil until it reaches 105mm from the top i reccomend using a ruler and just slide it inside then when it reaches 10.5cm/105mm re buildmoz-screenshot.jpg i will send a few picture to demonstrate

Aug 29, 2009 | 2001 Gas Gas EC 300

2 Answers

What fluid to put into front forks, rear shocks, trans

Read your owner's manual. You can get one from Amazon or your dealer.

Jun 06, 2009 | 1974 Yamaha DT 360

1 Answer

Where do i find year and model id on gas gas ec 300

should be on the steering neck
if not take the vin number and call your dealer they can tell you from the vin number

Apr 15, 2009 | 2001 Gas Gas EC 300

1 Answer

2007 EC 300 Speedo

not a bike battery)Is that the TrialTech version? If so it runs on AC or DC and has an internal CR2032 battery as well,,

Nov 10, 2008 | 2001 Gas Gas EC 300

Not finding what you are looking for?
2006 Gas Gas EC 300 Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gas Gas Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Kim Halliwell

Level 1 Expert

32 Answers

Livewyre Studio
Livewyre Studio

Level 1 Expert

26 Answers

Are you a Gas Gas Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides