Question about 2004 kawasaki VN 800 A Vulcan

Open Question

My 2006 kawasaki vulcan 900 sometimes stalls when idling at lights what would cause this

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
soloxilu
  • 65 Answers

SOURCE: process of changing the rear brake pad on the

Remove the 2 break bolts that hold the break to the bracket. Remove the pin covers on the side. <2 flat heads> Remove the Alan key pins and old pads will come out. Use a c clamp and a rag to compress the caliper piston. replace break pads pins and pin covers. Re bolt the break to the bracket. pump breaks till stiff. open bleeder. pump twice and close during pump. clean up and enjoy ;D

Posted on Jul 08, 2009

Ad
ollie reece
  • 1167 Answers

SOURCE: 2006 kawasaki 750 vulcan will not idle , will idle with choke

ok buddy on the carb will be some sort of screw and idle screw turn this in 1/4 of a turn with the machine running until it idles at 1000rpm also the choke will stall the engine when warm the choke is only for cold starts get back to me more info or problems f4d68ca.jpg

Posted on Sep 24, 2009

  • 221 Answers

SOURCE: Battery keeps dying in my Kawasaki 900

possible reg/rec issue or the stator....if you have a multi meter you can check the stator by unplugging and hooking up to the stator (component side), set multi meter to volts a/c and connect each plug for voltage. then do a residence test on the stator.
reg/rec issue, make sure you have proper ground, do a diode test to make sure that it is d/c and not a/c

Posted on Dec 27, 2009

  • 653 Answers

SOURCE: Kawasaki Vulcan 900 Custom - sat the winter,

Did you connect the poles correctly and are the bolts tight to keep good contacts?
Try usin a trickle charger to jump the battery.

Posted on Mar 24, 2010

19ken55
  • 426 Answers

SOURCE: 07 Kawasaki Vulcan 900 on start up the solenoid

Bad switch,Bad relay,bad solenoid the solenoid may need cleaning.
For troubleshooting remove the positive wire from the starter.
That is the biggest one. on the starter.
Now place a load on the wire say a headlight or 12 volt fan

Posted on Mar 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Kawasaki Vulcan 900 Classic fuses


Hi, Shauna for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2010 Kawasaki Vulcan 900 Classic fuses Google Search
Fuse Box Location
KAWASAKI VN900 CLASSIC Service Manual
OEM Parts for Kawasaki
2010 Kawasaki Vulcan 900 Classic LT Owner Manual

Jun 24, 2017 | 2010 kawasaki Vulcan 900 Classic

1 Answer

Runs for 30 minutes, then why does engine stop?


Hi, Freerick the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or damaged battery, 9 volts or lower.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Water or dirt in the fuel system, carburetor or filter.
11. Restricted, blocked or kinked fuel line.
12. Fuel tank empty.
13. Gas cap is not venting properly or fuel tank venting system blocked.
14. A failed fuel pump, pressure regulator and or fuel injectors.
15. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
16. Needle and seat stuck closed in the float bowl.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
http://www.kawasakimotorcycle.org/forum/kawasaki-cruisers/146296-2008-vulcan-900-custom-hesitates-hard-acceleration-after-about-20-30-min-riding.html
2008 Vulcan 900 CUts out and shuts off HElp Kawasaki Vulcan Forum Vulcan...
https://www.vulcanrider.se/en/kawasaki-vulcan-service-manuals http://www.kawasaki-techinfo.net/index.php?view_lang=EN&spec=OC

Jan 03, 2016 | 2008 kawasaki Vulcan 900 Custom

1 Answer

How to remove rear pulley on vulcan 900 custom


Hi Anonymous, I am sorry you can't find the first and best tool you ever bought for your Kawasaki but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
https://www.tradebit.com/filesharing.php/search/0/2012+kawasaki+vulcan+900+custom

Aug 16, 2015 | 2012 kawasaki Vulcan 900 Custom

1 Answer

I have 2006 kawasaki vulcan i am hooking a radio to it need to know best wirring for this.


is your vulcan dirter or clasic becuse some of the 800 n 900 c have a spar fues for a radio.if so just that off your set n see if ther is n exter fueis on your fueis box if so us it

Jul 31, 2013 | kawasaki Motorcycles

1 Answer

Cant locate oil sight glass for 2008 Kawasaki Vulcan 900 classic,where is it located


Not sure of the 900 Classic, but look to the rear of where the gear change pedal is attached to the splined shaft coming from the gearbox. Is the window there?

Feb 03, 2013 | 2008 kawasaki Vulcan 900 Classic

1 Answer

My battery for my 2006 vulcan 900 cant start bike every time temp outside is 32 degrees or below. Need to jump start it. But starts normally if warm temperature.


check battery connections to see if they are tight and clean. also check to see if it is proper battery for it. if it is a older battery it might be getting weak and need replaced. some auto parts stores will check them for free for you.

Jan 08, 2013 | 2006 kawasaki Vulcan 900 Classic LT

1 Answer

2006 vulcan won't charge


My 2006 vulcan 900 won't start after I replaced starter and battery. It makes a tickering sound when I try to turn it on.

Jul 28, 2012 | 2006 kawasaki Vulcan 900 Classic

1 Answer

Kawasaki Vulcan 900 Custom - sat the winter,


Did you connect the poles correctly and are the bolts tight to keep good contacts?
Try usin a trickle charger to jump the battery.

Mar 21, 2010 | 2005 kawasaki EN 500 Vulcan

1 Answer

2006 kawasaki 750 vulcan will not idle , will idle with choke


ok buddy on the carb will be some sort of screw and idle screw turn this in 1/4 of a turn with the machine running until it idles at 1000rpm also the choke will stall the engine when warm the choke is only for cold starts get back to me more info or problems f4d68ca.jpg

Sep 24, 2009 | 1992 kawasaki VN 750 Vulcan

Not finding what you are looking for?
2004 kawasaki VN 800 A Vulcan Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...