Question about Yamaha YZF-R1 Motorcycles

1 Answer

2008 R1 cooling fan not working even at over 103 degree centigrade. Have check: 1) Fan fuses- ok 2) Fan relay- ok 3) Bypass the relay, the fan is working 4) Ignition fuse- ok 5) temp sensor- ok 6) Wire contiunity-ok when i check the electrical diagram, one of the wire (yellow/green) from the fan relay goes to ECU, What do you think of the causes....ECU? Is there any other causes beside the ECU?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,100 Answers

I have a 2002 ducati monster S4, it's fans come on at 212 degrees F, that is about 108 degrees C, They only come on in city traffic, and they have only come on twice in 8 years. Your coolant boils at 265F in a closed system, so depending on what the thermostat is set at, they are probably just getting ready to come on at 103. I kinda wish I had a switch that I could turn them on at any time, so it sounds like your bike is running normal, also, my bike runs at exactly 100 degrees hotter than the outside air temp, always. Hope this helps.

Posted on Jul 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace coolig fan sending unit on a 2008 chevy uplander


Why ? Did you test ? Hook up a scan tool to see if the PCM/ECM - engine computer is reading coolant temp. ? Testing not guessing ? Do you even know how the system works .

The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the engine control module (ECM) to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the underhood fuse block.
During low speed operation, the ECM supplies the ground path for the low speed fan relay, which is Fan 1 Relay, through the low speed cooling fan relay control circuit. This energizes the low speed fan relay coil, closes the relay contacts, and supplies battery positive voltage from Fan 1 Fuse 29 through the cooling fan motor supply voltage circuit to the left cooling fan. The ground path for the left cooling fan is through the Series/Parallel relay, which is the Fan 2 Relay, and the right cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the ECM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. The ECM supplies a ground path for the high speed fan relay, which is the Fan 3 Relay, and the Series/Parallel through the high speed cooling fan relay control circuit. This energizes the Series/Parallel relay coil, closes the relay contacts, and provides a ground path for the left cooling fan. At the same time the Fan 3 Relay coil is energized, the relay contacts close to provide battery positive voltage from Fan 2 Fuse 33 on the cooling fan motor supply voltage circuit to the right cooling fan. During high speed fan operation, both engine cooling fans have their own ground path. The result is a parallel circuit with both fans running at high speed.
When the request for fan activation is withdrawn, the fan may not turn OFF until the ignition switch is moved to the OFF position or the vehicle speed exceeds approximately 10 mph. This is to prevent a fan from cycling ON and OFF excessively at idle.

Feb 27, 2017 | 2008 Chevrolet Uplander

2 Answers

I have 2007 Suzuki XL7. I replaced radiator and fan assembly. Fans do not work. Is there a relay? If so, where is it?


Most fan and Ac relays are located in the under hood fuse and relay box. Adequately marked in owners manual or on plastic cover

Sep 03, 2016 | Suzuki XL7 Cars & Trucks

1 Answer

Where are the sensors for radiator fan merc.2002 villager


Sensors for radiator Fan ? What sensor ? The coolant temperature sensor is an input to the PCM - engine computer ! When the engine temperature reaches 200 degree's the PCM energizes 1 to 3 Cooling fan relay's in the battery junction box (fuse-relays ) The low speed fan relay , High speed fan control relay 1 , an high speed fan control relay 2 . Now what problem are you having ? Go on you tube an check out videos on testing cooling fan's , testing relay's .Before you replace a sensor you don't need too .

Apr 30, 2016 | Cars & Trucks

2 Answers

Where is the fan relay on 1999 aurora located


Cooling Fan Relay No. 1
Center rear of engine compartment, left of the windshield wiper motor
7 - COOLING FAN #2 Relay
8 - COOLING FAN #3 Relay High Speed Cooling Fan Relay #3
9 - COOLING FAN Fuse
60A
Cooling Fan Relay #1, Cooling Fan Relay #2

Apr 18, 2016 | 1999 Oldsmobile Aurora

2 Answers

Where is the fuse for motor fan in uplander 2006?


there is 2 fuses that you have to check
one will be in the big fuse assembly in the engine bay, the other probably in the fuse assembly in the cab
If they prove ok then it is possible that the coolant temperature SENSOR is faulty and needs replacing
don't confuse it with the temperature sender which operates the temp gauge.

Aug 10, 2015 | 2006 Chevrolet Uplander

2 Answers

2004 Chevy Monte Carlo 3.4 the a/c stopped blowing,then it started overheating to the red within a couple miles,replaced the thermostat,the relay switch some days it overheats sometimes it runs fine


Are the cooling fans coming on ? What relay switch did you replace ?
The BCM will request low speed cooling fan operation from the PCM under the following conditions:
?€¢
Engine coolant temperature exceeds approximately 103?°C (217?°F).


?€¢
When A/C is requested and the ambient temperature is more than 10?°C (50?°F).


?€¢
A/C refrigerant pressure exceeds 1310 kPa (190 psi).


?€¢
After the vehicle is shut off if the engine coolant temperature at key-off is more than 117?°C (243?°F) and system voltage is more than 12 volts. The fans will stay on for approximately 3 minutes.


The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the PCM to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the engine wiring harness junction block. The ground path is provided at G101.
During low speed operation, the PCM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the FAN CONT #1 relay coil, closes the relay contacts, and supplies battery positive voltage from the FAN CONT #1 fuse through the cooling fan motor supply voltage circuit to the right cooling fan. The ground path for the right cooling fan is through the FAN CONT #2 relay and the left cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the PCM supplies the ground path for the FAN CONT #1 relay through the low speed cooling fan relay control circuit. After a 3-second delay, the PCM supplies a ground path for the FAN CONT #2 relay and the FAN CONT #3 relay through the high speed cooling fan relay control circuit. This energizes the FAN CONT #2 relay coil, closes the relay contacts, and provides a ground path for the right cooling fan. At the same time the FAN CONT #3 relay coil is energized closing the relay contacts and provides battery positive voltage from the FAN CONT #2 fuse on the cooling fan motor supply voltage circuit to the left cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.
Is your vehicles check engine light lit ?
Is the

Jul 10, 2015 | Cars & Trucks

2 Answers

2004 Venture Chevrolet minivan cooling fan circut


Are you talking about the radiator fan? How hot does the engine get in degrees F? Some makes and models, the radiator fan won't turn on till about 220 degrees F. Check for applicable trouble codes, see if any code that refers to the radiator fan circuit or coolant temp sensor? Some of the national brand auto stores will check codes for free.

Of course, as far as overheating in general, you have the thermostat--water pump and other possible issues. Are you losing coolant?

Dec 14, 2014 | Chevrolet Cars & Trucks

2 Answers

My cooling fan will not turn on. What could this be? I had someone tell me the water pump, but it does not leak.


Step 1:

This cooling fan circuit has 2 cooling fans and 2 cooling fan relays, both cooling fan relays are located in the BJB (battery junction box, underhood fuse box) there is a low speed or main cooling fan relay in cavity location # K-46 and the high speed relay is location # K-47! Also check the main cooling fan power fuse # 2 in the same BJB, The fuse is a MAXI-FUSE (large one) it is blue in color and is rated at 60amps!

Step 2:

Also check the coolent tempature sensor thats what signals the fan to turn on.

Step 3:

Do the fans turn on when you turn the a/c on. if not may have bad fan motor

Feb 27, 2013 | 1998 Ford Contour

1 Answer

Cooling fans on radiator will not come on. what can i do?


Hi kattrinahawk, If your cooling fans do not work, take a second to understand the system: 1)Fans will cycle on and off depending on engine temperature. 2)Fans will come on when Air Conditioning system is On. 3)Fans will come on if certain malfunctions in engine electrical systems. Fans are controlled via the ECM/PCM or sub computer. Fans usually have separate fuses and or relays/resistors. Ok so lets check a few things: 1)Check your engine coolant level, fan operation is depending on correct/full level 2)Turn your A/c on max settings and wait a few seconds see if fans cycle. 3)Check for obstructions or loose wiring around/on fans. 4)Inspect fuses per owners manual locations identification.

May 11, 2011 | 2008 Ford Escape

1 Answer

My car fan dont turn on when ac is off


Check the operation of the radiator cooling fan circuit:-
1) check fan control temperature sensor is ok,
2) check/replace the cooling fan control relay,
3) check supply fuse for cooling fan is ok.

Oct 01, 2009 | Hyundai Motor 2002 Elantra

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

483 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...