Question about Honda Fusion Motorcycles

1 Answer

Spark plug is not sparking it has a new spark plug .the lead is fine

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Can be the CDI check it

Posted on Jul 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not start, no spark


try this test. take off the spark plug cap ( they unscrew ) snip a small piece off the ht lead ( as the metal inside will be chewed from the thread of the cap ) with a new cut hold the lead against any metal near it ( the cylinder head etc ) and pull it over. you should see a spark from the lead ? if you do you can replace the cap ( it will have new wire to screw into now ) and try fro spark at plug ( no spark new plug needed ) ..if you get no spark from the ht lead unscrew it from the coil and try a new lead

Apr 30, 2015 | Poulan Pro PP133 17" Gas Trimmer

2 Answers

How to change the spark plug


1 Spark Plug Spanner 1 New Spark Plug

Pull H.T Lead off the top of Spark Plug, You need Spark Plug spanner to do the job. Untighten Anti Clockwise, Check Gap is correct on the New Plug ! Hand Turn the New Plug into hole, carefull as threaded. Tighten up , till tight , do not over tighten or you might strip thread, Put cap back onto Plug . FINISHED

Mar 14, 2015 | Garden

1 Answer

What do u do when spark is weak on Yamaha blaster


Check battery voltage, remove spark plug suppressor cap from HT lead and see if spark is good by holding lead in a gloved hand and placing the lead end near the engine. If spark good get a new suppressor cap. Check the plug shows a good spark in the new cap by holding the screw thread to the engine. Poor spark change spark plug. If you get a poor spark from the HT lead then get the ignition coil checked.

Oct 06, 2014 | Yamaha Motorcycles

1 Answer

Pulsar 150 wont show spark


Remove the spark plug, keeping the cap connected to the plug. Hold the threads of the spark plug to the cylinder head bolt.
- Lift the rear wheel, and give it one good hard pedal down as if you are kick-starting the bike.

IF the plug sparks at the tip, re-install the spark plug.
NO SPARK:
- Check the plug cap. I've replaced mine with a NGK Right Angle spark plug cap.
- Replace lead with Copper wire lead. (despite not noticing evident issues with the wiring)
- Check for spark again with the new lead and plug cap. That's all the electrical done from start of lead to the end of the plug tip.
- Still NO SPARK? Skip to [Magneto and CDI] DO NOT replace Magneto and CDI unless you do all the above. That way you have a clean sweep of any electrical related issues.

Jul 12, 2014 | 2005 Bajaj Pulsar 150

1 Answer

Yamaha 650 vstar not starting


did you check for spark ?
take the spark plug lead off and remove the spark plug
reconnect the loose spark plug to the spark plug lead - then place the spark plug on the engine and try to start - since you can see the live end of the plug - you should see a it sparking - do not touch the plug with the ignition on - or you will get a good jolt
test all spark plugs - if not here then it is probably a fuel problem

Jan 06, 2013 | Yamaha V Star Classic 650 Motorcycles

1 Answer

How to change spark plugs on a 2001 jeep wrangler 4 lr. engine


Remove spark plug leads, get the right sized deep socket and unscrew old spark plugs, screw in new spark plugs, plug in spark plug leads, DONE!

Oct 09, 2012 | 2001 Jeep Wrangler

1 Answer

Engine has no spark. 3HP Briggs and Stratton +


If you get a shock from the HT lead then you do have spark!!

Connect spark plug with it removed and shorted to see if there is spark, if not use screw driver to hold away from steel (1/4") with end inserted in HT lead,If good spark / faulty spark plug.

Check for
Spark
Fuel to spark plug
No air leaks.

Mar 16, 2010 | Briggs & Stratton 1928 1 amp Transfer...

1 Answer

I want to change the leads on the spark plugs. i


The part that you unscrewed from the spark plug is what allows the plug cap to snap onto the plug. Screw the little adaptor back onto the spark plug - and the plug cap should then snap into place with a little pressure.

Nov 16, 2009 | 1994 Land Rover Discovery

2 Answers

Fiat Sicentio 1.1 (02 plate) problem after changing spark plugs


check spark plug gaps are set correctly and that leads are in correct order if you took all leads off at same time its easy to mess up just one or two

Nov 08, 2008 | 2007 Fiat X1/9

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...