Question about 1990 Honda CB 1

1 Answer

1990 Honda CB 1 no electrical power

I have a Honda CB1 400 1990 model import And she has just recently refused to start on the button, in fact, she won't start at all I have checked the fuses .O.K. I did let her run low on fuel so now she is full up and the bat is flat as she still refused to run no attempt to fire up has she got a fuel filter problem or what. @

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Honda Master
  • 49,362 Answers

Hi, Oliver_bye before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Frustrating starting problem still happening
won start Honda CB1 forum
1989 1990 Honda CB 1 CB400F NC27 Service Manual Moto Data Project
https://www.partsfish.com/page/oem-parts-for-honda
HONDA CB400F 1989 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on Feb 15, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 74 Answers

SOURCE: 1995 honda cbr f3 wont start

I would think about investing in a carb re-build kit.

Posted on Dec 22, 2008

  • 72 Answers

SOURCE: To Honda ST1100 experts. Fuel starvation

your carburetors need top be removed from the bike and supmerged in a big pot of yamaha carburetor cleaner . And then blow thew it with air hose (45-75) psi

Posted on Mar 20, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: car not getting fuel to carb

Hello Mike...did you check fuel the pump relay? It is located to the
left of fuse box, wedged against left kick panel and above hood latch. Remove fuse box cover and lower dash panel for access. Check the voltage to the fuel pump circuit. You should be able to hear the pump "wizzz" when you turn the key on. Useing starting fluid is a no no...will result in cylinder scaring, possible explosion and bodily harm...Also...if the check engine light is on diagnostic trouble codes need to be retrived and corrected.
Good luck...i hope this helps

Posted on May 15, 2009

  • 10 Answers

SOURCE: Fluid amounts forks cb1 1990

The best way to find this out is to use the honda service manual... It gives all the specs. you need!

Posted on Jun 14, 2009

  • 125 Answers

SOURCE: Honda Shadow VLX 600 cellenoid

I think the starter works off of a one-way clutch.
Go over your wiring once again. Make sure all the switches are in their correct positions.
Be sure the battery was properly charged before installation.

Posted on Jun 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Honda CB 125 T no electrical power


Hi, Anonymous before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike wont start no lights or anything Page 2 Honda Motorcycles FireBlades...
No electrical power
Honda CB125 Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CB Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Aug 07, 2013 | 2001 Honda CB 125 T

2 Answers

Press the starter button nothing happens 1983 Honda CB 1100R


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Starting issue push the start button and nothing happens
GL1100 Starter button no respense doesn start
Honda CB1100R Manuals Literature eBay
https://www.partsfish.com/page/oem-parts-for-honda
Honda CB Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Feb 22, 2013 | 1983 Honda CB 1100 R

1 Answer

What are the Honda CB-1 carburetor float specifications? @


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Need proper float height settings
Adjusting Carburetor Float Level
1989 1990 Honda CB 1 CB400F NC27 Service Manual Moto Data Project
https://www.partsfish.com/page/oem-parts-for-honda
HONDA CB400F 1989 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Jul 18, 2012 | 1989 Honda CB 1

1 Answer

How to remove a 1990 Honda Goldwing GL 1500 factory CB radio?


Hi, George for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
GL1500 CB Radio Removal GL1500 Information Questions goldwingdocs com
GL1500 CB radio install Help
Template service manual $5 donation very cheap
http://www.partsfish.com/page/oem-parts-for-honda
Honda Goldwing GL1500 SE Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 06, 2017 | 1990 Honda GL 1500 SE Gold Wing

1 Answer

2000 Honda CB 250 Nighthawk no electrical power no electrical power


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1991 Honda Nighthawk CB250 suddenly won start help
Troubleshooting No Start Honda Motorcycle
Honda CB250 Shop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda CB250 Nighthawk Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


May 03, 2012 | 1992 Honda CB 250 Nighthawk

1 Answer

My honda accord 1998 model stopped on the way and refused to start again. No electrical problem and my Mechanic is saying compression is low and we need to ring it ie change rings. Is that a possibility...


The fact is that you need to increase compression. Hwat you need to confirm is the cause of the problem.
1. Valves not closing - several reasons for that
Valve seats worn, valve guides worn, valves bent, cam timing out.
2. The rings-depending on oil quality in use you might not see smoke beacause some oils don't burn easily.

Oct 24, 2011 | 1998 Honda Accord

1 Answer

1989 Honda CB 1 how to service the rear mono shock


Hi, Gavin_I_will for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
HONDA CB 1 1989 1990 Emulsion Gas YSS Mono Shock
Rear Shock Rebuild part 1
Honda CB400 Service Manual English pdf
https://www.partsfish.com/page/oem-parts-for-honda
http://www.ownersmanual.biz/1989-honda-cb-1-cb400f-owners-manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Aug 08, 2010 | 1989 Honda CB 1

1 Answer

1989 Honda CB 1 carburetor float height


Hi, Bryndynw for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1989 Honda CB 1 carburetor float height Google Search
Need proper float height settings
1989 1990 Honda CB 1 CB400F NC27 Service Manual Moto Data Project
https://www.partsfish.com/page/oem-parts-for-honda
HONDA CB400F 1989 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Mar 19, 2010 | 1989 Honda CB 1

1 Answer

Fluid amounts forks cb1 1990


The best way to find this out is to use the honda service manual... It gives all the specs. you need!

Apr 13, 2009 | 1989 Honda CB 1

Not finding what you are looking for?
1990 Honda CB 1 Logo

Related Topics:

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5060 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...