Question about 2008 Moto Guzzi Stelvio

Open Question

What is the torque value in Nm for the rear wheel on a Stelvio

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What the torque settling on a 1.8spi vauxhall cavalier 1994


Cylinder head Renew bolts: Yes Tighten: 25 Nm Tighten: 90° Tighten: 90° Tighten: 90° Other engine tightening torques Main bearings Renew bolts/nuts: Yes Main bearings Stage 1: 50 Nm Main bearings Stage 2: 45°-60° Big end bearings Renew bolts/nuts: Yes Big end bearings Stage 1: 35 Nm Big end bearings Stage 2: 45°-60° Oil pump to cylinder block : 6 Nm Sump bolts : 15 Nm Sump drain bolt : 55 Nm Flywheel/driveplate :
  • Use new bolts and tighten as follows:
      • 1,4/1,6 = 35 Nm + 30° + 15°
      • 1,8/2,0 = 65 Nm + 30° + 15°
  • "Pot"-type flywheel = 65 Nm + 30° + 15°
  • Tighten drive plate to 60 Nm.
Clutch pressure plate : 15 Nm Crankshaft pulley/damper centre bolt : Use new bolts. Tighten centre bolt to 130 Nm + 40°-50°
Camshaft sprocket/gear : 45 Nm Camshaft/rocker cover : 8 Nm Inlet manifold to cylinder head : 22 Nm Exhaust manifold to cylinder head : 22 Nm Spark plugs : 25 Nm Lambda sensor (Oxygen) : 30 Nm Chassis tightening torques Front hub :
  • Tighten nut in three stages:
    1. 130 Nm
    2. Slacken off
    3. 20 Nm + 80°-90°.
Steering track rod end : New nuts 60 Nm Brake disc to hub Front: 4 Nm Brake caliper to carrier Front: 30 Nm Brake caliper/carrier to hub Front: 95 Nm Brake caliper/carrier to hub Rear: 80 Nm New bolts ABS sensor Front: 8 Nm ABS sensor Rear: 15 Nm Road wheels : 110 Nm
There you go pretty much covers everything hope that helps

Jan 11, 2015 | Vauxhall Cars & Trucks

1 Answer

Torque specifications


You have the wrong size Torque Wrench. IF you Torque Wrench measures nm, and it max'd out @ 130, you need a larger Torque Wrench. Convert nm to Ft. Lb and use these if necessary.

Sep 06, 2014 | Cars & Trucks

1 Answer

Remove rear wheel on 2012 flhtc harley


To remove a 2012 TOURING rear wheel FIRST remove the saddlebags, then raise the wheel with a suitable lifting device and rotate the wheel and inspect the wheel bearings. THEN remove left side muffler, on models equipped with low profile shock absorbers (FLHX, FLTRX), remove the left side lower saddlebag support rail and if ABS equipped remove the cable strap to releasethe rear wheel speed sensor cable from the rear brake hose and at no time ever left any magnetic force field exist or be close to the speed sensor or it will be ruined, remove the rear brake caliper but do not disconnect the brake hose, set the brake caliper on the passenger footboard or otherwise appropriately support it, remove the E-clip from the groove at the end of the axle, hold the weld nut on the left side of the axle and loosen the cone nut on the right side of the axle using an AXLE NUT TORQUE ADAPTER available from JIM's or H-D (HD- 47925), remove the cone nut and the adjuster cam from the axle, rotate the weld nut on the left side of the axlecounterclockwise until the wheel is loose, remove the axle from the left side of the motorcycle, catch all of the external spacer(s), caliper bracket, and rear wheel speed sensor (if ABS equipped) as the axle is removed, remove the caliper bracket from the anchor weldment on the rear fork, move wheel forward enough so that you can and slip the drive belt off of the compensator sprocket, if needed remove the brake disc from hub and be careful that the drive sprocket does not fall off and get damaged as you remove the wheel from the bike, mark the wheel and the disc for re-installation in the same orientation.

To install a 2012 TOURING rear wheel you will need FASTENER TORQUE VALUEs. The brake disc (rear) screws are 30-45 ft-lbs 41-61 Nm; (Do not re-use brake disc/rotor screws because re-using these can result in torque loss and always reinstall a brake disc in its original orientation); the rear axle cone nut (preliminary - 15-20 ft-lbs 20-27 Nm) (Final 95 to 105 ft lbs 128.8-142.4 Nm ) ; Brake caliper (rear)mounting fasteners 43-48 ft-lbs 58.3-65.1 Nm. If the brake disc was removed from the wheel ALWAYS reinstall it in the same orientation with the wheel as when it was removed and ALWAYS use NEW attaching screws and tighten them in a crosswise pattern to 30-45 ft-lbs (41-61 Nm), verify that the sprocket is square to and fully seated in the bowl area of the wheel, place the wheel into the rear fork with the drive sprocket installed, install the belt over the drive sprocket and then slide the wheel back to take up the slack, seat the brake caliper bracket on the anchor weldment of the rear fork, apply a light coat of wheel bearing type grease (H-D suggest silver anti-seize compound but this technician finds almost all seized, corroded axles were lubricated thus so do as you feel best) to the axle to the bearing bores and to the bore of the spacer sleeve, slide the axle through the left side of rear fork, the thin external spacer, the sprocket and into the wheel hub out the other side of the wheel hub and through the rear wheel speed sensor if ABS equipped and if ABS equipped ensure that the grooves on the external spacer, or index pin on the rear wheel speed sensor are on the outboard side or through the thick external spacer if not ABS equipped, the brake caliper bracket, and the right side of the rear fork, rotate the axle so that the flat on the threaded end is topside and with the adjuster cam section forward, install the adjuster cam on the right end of the axle, apply a light coat of SILVER GRADE ANTI-SEIZE (H-D Part No. 98960-97) to the inboard side of the cone nut but NOT the threads, install the cone nut on axle finger tight only, if ABS equipped route the speed sensor cable forward and outboard of the brake caliper bracket, continue forward following the top of the rear fork, rotate the speed sensor in a counterclockwise direction until the index pin makes contact with the brake caliper bracket, tighten the cone nut to a preliminary torque of 15-20 ft lbs (20-27 Nm), install the brake caliper and tighten its screws to 43-48 ft-lbs (58.3-65.1 Nm), secure the rear wheel speed sensor cable to the brake hose with the conduit clip located approximately 1.25 in. (31.8mm) in front of the brake hose crimp, adjust the drive belt using a belt tension gauge, final tighten the cone nut to 95 to 105 ft lbs 128.8-142.4 Nm, install a new E-clip with the flat side out in groove on the right side of the axle, on models equipped with low profile shock absorbers, install the left side lower saddlebag support rail, install the left side muffler and tighten its fasteners to 96-144 in-lbs 10.9-16.3 Nm,depress the rear brake pedal a number of times to set the brake pads properly against the brake disc, install the saddlebags and THEN road test the vehicle.

May 28, 2014 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Bolt torque wheel bearing


NONE for axle bearings but for a 2005 DYNA Rear axle the torque is 60-65 ft-lbs 81.3-88.1 Nm

Apr 22, 2014 | 2005 Harley Davidson FXDL - FXDLI Dyna Low...

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

How to disassemble the rear end in a 2000 gmc yukon and how to remove axles


Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Loosen the lug nuts on the wheel and tire assemblies but do not remove the lug nuts
  3. Raise and support the vehicle
  4. Remove or disconnect the following:
    • Wheel and tire assemblies
    • Axle lubricant into a suitable container
    • Rear driveshaft
    • Parking brake cable
    • Brake calipers
    • Shock absorbers from the axle brackets
    • Vent hose from the rear axle vent fitting
    • Nuts and the washers from the U-bolts
    • U-bolts, spring plates and spacers from the axle assembly
  5. Lower the axle assembly from the vehicle
To Install:
  1. Place the rear axle assembly under the vehicle
  2. Align the rear axle assembly with the springs then connect the spacers, spring plates and the U-bolts to the rear axle
  3. Raise the rear axle assembly into position
  4. Install or connect the following:
    • Washers and nuts to the U-bolts; Torque to: 59 lb-ft. (80 Nm) then, Torque to: 89 lb-ft. (120 Nm)
    • Vent hose to the rear axle vent fitting
    • Shock absorbers to the rear axle
    • Brake calipers (See: Brake Caliper)
    • Parking brake cable (See: Parking Brake Cable)
    • Rear driveshaft (See: Rear Driveshaft)
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  5. Fill the rear axle with lubricant
  6. Bleed the brake system (See: Brake Bleeding)
  7. Install the wheel and tire assemblies
  8. Lower the vehicle to the ground
  9. Torque lug nuts as follows:
    • Single Wheel: Torque to: 140 lb-ft. (190 Nm)
    • Dual Wheel: Torque to: 175 lb-ft. (240 Nm)
  10. Road test the vehicle to check performance
prev.gif next.gif

Aug 03, 2010 | 2000 GMC Yukon XL

1 Answer

Need specs for changing rear and front tires for 2002 royal star venture including torx specs


I'll include the obvious, since I'm not sure exactly what you need:

Front tire - 150/80-16 Dunlop D404F or Bridgestone G705, recommended inflation 36 p.s.i.

Rear tire - 150/90-15 Dunlop D404 or Bridgestone G702, recommended inflation 36 p.s.i., 41 p.s.i. with passenger or load.

The front tire can be removed (motorcycle on lift) without loosening calipers or any other parts once axle shaft has been withdrawn; after the tire has been changed and the wheel and axle shaft is back in place, torque for the axle nut is 58 ft.-lbs (78 nm) and the pinch nut is 14 ft.-lbs. (19 nm).

The rear tire requires removal of the right saddlebag and brake caliper, as well as the axle shaft. During reassembly, the torque for the axle nut is 110 ft.-lbs. (150 nm), for the pinch nut on the swing arm 17 ft.-lbs (23 nm). Bolts for the caliper should be torqued to 30 ft.-lbs. (40 nm).

It's a good idea to lubricate the drive splines in the rear wheel and the mating shaft in the final drive while the rear wheel is out.

Apr 15, 2010 | 2002 Yamaha Royal Star Venture

2 Answers

NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS


  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Feb 01, 2009 | 1997 Dodge Avenger

1 Answer

NP 249 bolt torque specs


Hi brian_cherve hope these values will help you out my friend
Trans case attachment nuts = 35 Nm (26 ft lbs)
Propeller shafts attachment bolts = 19 Nm (170 in lbs)
Rear crossmember bolts = 41 Nm (30 ft lbs)
good luck and take care :)

Nov 12, 2008 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
2008 Moto Guzzi Stelvio Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Moto Guzzi Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

vtrktrmn

Level 2 Expert

184 Answers

Are you a Moto Guzzi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...