Question about 2002 Honda CR 250 R

2 Answers

How do you bypass a bad ignition temporarilly to et it started untill it is replaced, the key was tampered with and destroyed

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Undo the barrel take out the switching plate then you'll see from there join the green and blue togeouther and the red and black togeouther and your away

Posted on Apr 13, 2012

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 42 Answers

Well, hopefully I am not helping you steal a bike, but the most effective say to do it is to disconnect the switch, and use a jumper wire to connect the two hot wires.

Posted on Aug 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What will cause my 2002 buick ultra not to start how do i reset security sytem


chip in key is bad or needs to be reset, look on web for how to reset keys. Could be computer module needs replacing or could be starter.

Jul 23, 2014 | Vehicle Parts & Accessories

1 Answer

My 2002 gmc envoy starts with remote but will not crank with keys


The remote start bypasses the ignition portion of the antitheft security system to allow you to remotely start the truck. But the system still needs the signal from the key to allow the vehicle to remain running and drive. I would assume the ignition is bad or needs to be trained to the system if it was replaced.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Mar 29, 2014 | 2002 GMC Envoy

1 Answer

Where will I find the ignition cylinder tamper switch on a 98 lincoln town car


Its just about impossible to bypass. You would need a key that matches the old key chip cut to the new tumblers. Each key has a chip in it that the computer looks for.

Jan 25, 2014 | 1998 Lincoln Town Car

2 Answers

Someone tried to steal my 2000 Chevy S10 pickup. They tore up ignition. I purchased a new ignition cylinder which came with 2 keys. I tried to do the 30 minute relearn but the security light does not stay...


You don't need to program key's with this anti-theft system , there is no chip inside . Did you get a correct lock cylinder. . On this system there is a pass lock sensor in side an the lock clinder has a magnet !
Passlock™ Sensor
The passlock™ sensor is inside the upper right side of the steering column. The passlock™ sensor contains 2 hall effect sensors. The tamper hall effect sensor is on the top. The security hall effect sensor is under the tamper hall effect sensor. Both of the hall effect sensors monitor the magnet of the lock cylinder through an opening. The tamper hall effect sensor is physically placed on top of the security hall effect sensor. This arrangement enables the tamper hall effect sensor to engage first if an intruder attempts to bypass the passlock™ sensor by placing a large magnet around that area of the steering column. There is a tamper resistor inside the passlock™ sensor in order to help prevent tamper to the system. Passlock™ equipped vehicles have a selection of 10 different security resistors ranging from 0.5K ohms up to 13.6K ohms. Installing one of the security resistors inside the passlock™ sensor will generate a unique passlock™ code. All 10 combinations of the passlock™ sensor have the same part number. However, you cannot simply replace the passlock™ sensor and expect the system to operate properly. Always start by performing the Diagnostic System Check first and following the instructions.
Body Control Module
The Body Control Module (BCM) contains the theft deterrent system logic. The BCM reads the passlock™ data from the passlock™ sensor. If the passlock™ data is correct, the BCM will pass theft. The BCM will then transmit the code password to the VCM/PCM.
During the tamper mode the vehicle may start. The vehicle will then stall. If the BCM receives the wrong passlock™ data, the VTD will immediately go into the tamper mode. The tamper mode will lock-out the vehicle fuel injectors for 10 minutes. The SECURITY indicator will flash while the VTD is in the tamper mode.
If the passlock™ sensor sends a correct password to the BCM when the ignition is in the ON position, the BCM will send a fuel enable signal to the VCM/PCM. The VCM/PCM will not disable the fuel due to any BCM message for the remainder of the ignition cycle.

You only need to do a relearn if one of these are replaced
Use this procedure after replacing:
• Passlock™ Sensor
• BCM
• VCM
• PCM

Did you replace any of these ?

30 Minute Re-Learn Procedure
Turn ON the ignition, with the engine OFF.
Attempt to start the engine, then release the key to ON (vehicle will not start).
Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
Turn OFF the ignition, and wait 5 seconds.
Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes ( the vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK).
Important: The vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
Start the engine (the vehicle has now learned the Passlock™ Sensor Data Code and/or password).
With a scan tool, clear any DTCs if desired (history DTCs will self clear after 100 ignition cycles).

May 18, 2017 | Chevrolet S 10 Cars & Trucks

1 Answer

Bypass ignition switch/antitheft


Check with your local lock smith, most of them cam reprogram your PATS system. Buy an ignition switch with keys from an autoparts warehouse or online but make sure that the one you order hase PATS keys. the description should not " programming required" You will have to have 2 keys.

Dec 18, 2013 | 1997 Lincoln Mark VIII

2 Answers

Trying to reboot in tamper mode


default pass is 123456 to take out of tamper mode

Nov 11, 2013 | VeriFone Omni 3700

2 Answers

My trail blazer 2006 wont start and it has a light on of a car with a lock what does this mean heeelp please as soon as possible emergency


You have now experienced GM's terrible anti theft security system. These systems are known for failing and will cost you an arm and a leg to fix. Anywhere from $350 - $700 plus labor. Most mechanics wont even touch these "PASSkey" security systems.You'll have to go to a Dealer mechanic. The good news is that you can bypass these systems permanently. And you're vehicle is one of these lucky ones that CAN be bypassed. This link should help you find what you need and help inform you of how this system works.

http://vatspasslockpasskeysecurityhelp.yolasite.com/ TRAILBLAZER 2002 2003 2004 2005 2006 2007 2008 Effected by Passlock/PASSkey Failure. tayjoejoe_17.jpg

Jul 11, 2011 | 2006 Chevrolet Trailblazer

1 Answer

Turn key to start truck but nothing happens, security light is on. lights and everything works


does the starter motor turn? the security light is an indicator of tamper mode. in tamper mode you will not able to start the vehicle until you reset the Passlock system by leaving the key in the ON position for 10-20 minutes.
tamper mode is a result of an unauthorized engine start attempt (such as a "hotwire") or a malfunction in the ignition cylinder.

Mar 04, 2011 | 2001 Chevrolet Silverado 1500

1 Answer

Turning ignition key there is silence....battery is ok as lights, radio come on strong. I keep trying, turning the key and moving gear shift et...and maybe it finally connects and engin fires and starts...


When this happens and the key is in the Ignition position, do the dash lights, etc come on? Could be the ignition switch is bad, and this is and easy way to tell. If the ignition is on and when we go to START, nothing happens, I would replace the starter/solenoid next.

Oct 19, 2009 | 1998 Cadillac Seville

Not finding what you are looking for?
2002 Honda CR 250 R Logo

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5060 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...