Question about 2006 kawasaki ZZR 600

1 Answer

2006 zzr600 just changed oil now oil light won't go off

Posted by on

  • creynoldszx6 Jul 16, 2010

    figured it out there was air in the pump...loosen oil filter start bike when oil comes out shut off bike tighten filter .

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,272 Answers

First try reset. Disconnect the battery for 5 mins reconnect and see if it resets? If that is not helping. Then ,Did you prefill the oil filter? if not start the bike up and crack the oil filter just a hair to burp the air air out of the system and then tighten it back up or just take the filter off and fill it with oil before putting it on.You need to bleed the system by unscrewing the oil filter a bit. start the bike. when oil pours out of the filter, tighten it back up. The procedure to change oil is as follows:-- drain oil, drain oil filter, put the oil pan nut back in, put a new oil filter on and lube the outer edge 1st (oil filter is the correct one), then add 4 quarts of mobile 1 10w-40 and hand tighten the oil filler cap/ . If it's a spin-on filter you'll likely lose about a quart of oil. To be safe, drain all the new oil into aclean pan, then re-use it after re-installing the filter. If all the possibilities checked ok.Then there are two possibilities that has to be checked,.That is the oil filter switch and oil sensor. the wire for the oil pressure switch got damaged or disconnected during the oil change, or the sensor itself got damaged. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Posted on Jul 15, 2010

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse box kawasaki junction zzr600


bad earth connection on engine to frame

Nov 11, 2013 | 2008 Zongshen Storm V250

1 Answer

Cataylic converter 2006 suzuki reno


Your engine's computer has detected a problem with it's engine management controls. The work you had done should have nothing to do with it.
Until you have the computer scanned (with an OBD2 scanner-Autozone will do it for free), you won't know what the check engine light is for. The scan will provide trouble codes for a technician to fix the problem. If it's a simple problem, you may be able to do it yourself. But only the code or codes will tell you why the light is on.
Good luck.

Nov 24, 2011 | 2006 Suzuki Reno

1 Answer

Kawasaki ZZR 600 clutch noise


Hi, Tompolv6 I would love to help you with your engine or chassis noise but I just loaned my brand new pair of listening ears to your local dealer's chief technician so he could take your bike for a test ride and give you his professional opinion and estimate about your noise and repair cost. If you are a little short on "DRACHMA" and a Dealership is not on your list of fun places to visit then perhaps the list below will help soothe your worried mind so you can make an informed decision.
1. Bearings---SCREECH
2. Belts---CHIRP
3. Brake Rotors---BUZZ
4. Chains---RATTLE
5. Clutches---CHATTER
6. Cylinders---PING
7. Fairing Panels---WHISTLE
8. Fronk Forks---Plunk
9. Gears---WHINE
10. Head Gasket---HISS
11. Hydraulic Lifters---TAP
12. Pistons---SLAP
13. Rear Shocks---SQUEAK
14. Shifting Trans---CLUNK
15. Solid Lifters---TICK
16. Starters---CLICK
17. Connecting Rods Go---KNOCK-KNOCK---who's there, it's me "*****"
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
03 zzr600 Loud clunking noise at idle
zzr600 clutch noise
Kawasaki ZZR 600 Complete Service Repair Manual Download Manuals Technical $10
OEM Parts for Kawasaki
2006 Kawasaki ZZR600 Owner Manual

May 25, 2017 | kawasaki ZZR 600 Motorcycles

1 Answer

I was riding, doing 80mph and bike began to slow down on its own so i gave opened the throttle and nothing happened i looked at my gauges and saw that the oil light was on, i switched to a lower gear and...


the oil light comes on any time the bike isn't running or pressure is low. sounds like u ran out of gas though. did u switch over 2 the reserve or is it completly empty

Oct 20, 2010 | 2006 kawasaki ZZR 600

1 Answer

Temperature increase 06 zzr600


Check coolant level and circulation. I would replace the themostat. Also check the fuse for the fan and you could unplug fan use a jumper wire to see if fan is working. The you could do an ohm check on the temp sensor

Feb 08, 2010 | 2006 kawasaki ZZR 600

1 Answer

How do I find parts for a ZX600J?


Call a Kawasaki dealer and give them the VIN (frame number). They can look it up and tell you exactly what you actually have.

Dec 29, 2009 | 2006 kawasaki ZZR 600

Not finding what you are looking for?
2006 kawasaki ZZR 600 Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...