Question about 2007 Boss Hoss BHC-3 ZZ4

1 Answer

Rear brake light & signals not working .yellow indecater on handlebars not coming on .not a fuse

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Boss Hoss Master
  • 43,120 Answers

Hi Aryals, before diagnosing any turn signal issue make sure the bulb is good and the light fuse has continuity with a test light. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue, please visit the websites below. Good luck and have a nice day. diagnosing and repairing turn signal problems
Motorcycle Electrical System Maintenance Part 1 of 2
http://antakesuma.xyz/fds/b/boss-hoss-bhc-3-ls2-2008-custom-cruiser-v8-automatic-repair-manual.pdf
https://www.bosshoss.com/parts.asp
Boss Hoss Cycles Contact Us

Posted on Dec 27, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

2 Answers

I have a 1999 Ford contour lx neither the brake lights nor the turn signals will work what would cause this


a fuse number 24,,,
The following specifications are for the Ford Contour and Mercury Mystique manufactured throughout 1995-2000.
Fuses Rating Color Circuit Engine bay fuse box 1 80 Black Power supply to main fuse box 2 60 Yellow Radiator fan 3 60 Yellow ABS 4 20 Yellow Daytime running lights 5 30 Light green Fog lamp 6 30 Light green Not used 7 30 Light green ABS 8 30 Light green Air pump 9 20 Light bue PCM module 10 20 Light bue Ignition switch 11 3 Violet PCM memory 12 15 Light bue Horn & hazard flasher 13 15 Light bue Oxygen sensor 14 15 Light bue Fuel pump 15 10 Red Right-hand low beam Passenger compartment fuse box 16 10 Red Left-hand low beam 17 10 Red Right-hand high beam 18 10 Red Left-hand high beam 19 7.5 Brown Heated door mirrors 20 10 Black Windshield wipers 21 30 Light green Electric windows 22 7.5 Brown ABS 23 15 Light bue Reverse lights 24 15 Light bue Brake lights 25 20 Yellow Door locks 26 20 Yellow Main light 27 15 Light bue Cigarette lighter 28 30 Light green Power seats 29 30 Light green Heated rear window 30 7.5 Brown Engine management 31 7.5 Brown Instrument pannel lights 32 7.5 Brown Radio 33 7.5 Brown Front and rear sidelights (left) 34 7.5 Brown Interior lighting & clock 35 7.5 Brown Front and rear sidelights (right) 36 30 Light green Air bag 37 30 Light green Heated blower 38 Unused Relays Color Circuit Location Engine bay fuse box R1 Green Daytime running lights (Canada) R2 Black Radiator fan (high speed) R3 Blue AC cut-out R4 Brown AC clutch R5 Dark green Radiator fan (low speed) R6 Yellow Starter R7 Brown Horns R8 Brown Fuel pump R9 White Low beam headlights R10 White High beam headlights R11 Brown PCM power supply Passenger compartment fuse box R12 White Interior and courtesy lights R13 Yellow Heated rear window R14 Yellow Heated blower R15 Green Windshield wiper motor R16 Black Ignition R17 Unused R18 Black One touch window switch Driver's door R19 Blue Cruise control cut-off Central fuse box bracket R20 Unused R21 Unused R22 White Fog lights Interface module bracket R23 Black Turn signals Steering column R24 White Left-hand flasher Door lock module bracket R25 White Right-hand flasher Door lock module bracket R26 Unused Bulbs / Lights Wattage Type Low beam headlamp 55 9006 Halogen High beam headlamp 55 9005 Halogen Parking / Side light 5 2357A Wedge Front turn signal 21 2357A Bayonet Rear turn signal 21 1157 Bayonet Tail light 21 1157 Bayonet Stop light 21 1157 Bayonet High mount stop light 5 2723 Bayonet Fog/Driving light 55 893 Halogen License plate 5 6418 Festoon Reverse light 21 1156 Bayonet Front sidemarker 5 2357A Wedge Glove box Map light 5 64111 Wedge Dome light 10 6411 Feston Step/Courtesy light Trunk/Cargo area Engine compartment 10 89 Wedge Instrument-general Automatic trans indicator

Apr 15, 2015 | 1999 Ford Contour

1 Answer

Nissan Xterra Brake Light Fuse Location


It's 15A FUSE 39 in the fuse & fusible link box

Mar 25, 2017 | Nissan Xterra Cars & Trucks

1 Answer

I have a 2000 roadking. the brake light is not working but the tail light works. changed bulb there is power going to the brake light switch an u can hear the relay clicking when you hit the brakes. but if...


To begin with, there is no relay for the brake light. That thing you hear clicking is a circuit breaker. You probably have a short circuit between the rear brake light switch underneath the bike and the brake light itself. If the tail lights work, then you know what circuit is ok.

Look at your rear brake master cylinder. Find the metal line coming out of it going to the rear of the bike. In that line, under the bike, you'll find a pressure switch. This is the rear brake light switch. The front brake light switch is located in the right side handlebar switch housing. If neither switch works the brake light, odds are you have a short circuit in the wiring from the rear brake light switch to the rear brake light itself.

Good Luck
Steve

Feb 25, 2011 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I replace my brake switch & my light don't work? when i stop


IF THE FUSES INSIDE THE CAR & UNDER THE HOOD HAVE ALL BEEN CHECKED WITH A GOOD FUSE TESTER, & THE BRAKE LIGHT SWITCH REPLACED, THE TURN SIGNAL SWITCH IS NEXT. THE BRAKE LIGHTS GO THROUGH THE TURN SIGNAL SWITCH SO THEY CAN BE USED AS TURN OR BRAKE LIGHTS. I'M ASSUMING THE BULBS ARE OK. REMOVE THE PLASTIC FROM AROUND THE TURN SIG. SWITCH. STAY AWAY FROM ANY WIRES THAT ARE IN THE YELLOW SLEEVE. THEY ARE AIR BAG WIRES. WITH BRAKE PEDAL DEPRESSED, THERE SHOULD BE POWER IN THE WHITE WIRE. IF THERE IS NO POWER IN THE WHITE WIRE, YOU MAY HAVE TO PUT A BYPASS WIRE FROM THE WHITE WIRE COMING OUT OF THE BRAKE LIGHT SWITCH TO THE WHITE WIRE GOING INTO THE TURN SIGNAL SWITCH. IF THAT DOESN'T MAKE THE BRAKE LIGHTS WORK, THE TURN SIGNAL SWITCH MUST BE BAD.

Jan 26, 2011 | 1999 Chevrolet Malibu

1 Answer

I have 1999 Blazer with brake light out on driver side only. All other lights work. Replaced bulbs but nothing changed. Swapped the working lights from the other (right side) with the driver side but...


THE BRAKE LIGHTS DO GO THROUGH THE TURN SIGNAL SWITCH. TO TEST, REMOVE THE PLASTIC COVER AROUND THE THE COLUMN, UNDER THE STEERING WHEEL. THE TURN SIGNAL SWITCH MUST BE IN THE OFF POSITION. YOU WILL NEED TO EXPOSE THE WIRES UNDER THE STEERING WHEEL. DO NOT DISTURB THE WIRES IN THE YELLOW JACKET. THEY ARE AIRBAG WIRES. YELLOW PLUGS YELLOW JACKETED WIRES ARE AIRBAG.THE WIRE IN QUESTION HERE IS YELLOW BUT IT IS NOT IN A YELLOW JACKET, [ SLEEVE ]. NOW, PUSH ON THE BRAKE PEDAL. THE YELLOW WIRE IS LEFT REAR TURN & BRAKE WIRE, DARK GREEN IS RIGHT REAR TURN & BRAKE WIRE. BRAKE PEDAL DEPRESSED, IF BOTH OF THOSE WIRES HAVE POWER, ALL OF THAT IS OK. IF THE YELLOW WIRE HAS NO POWER TURN SIGNAL SWITCH IS BAD

Jan 16, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

I took off my front signals & past the rest of the wiring through the handlebars & made sure to solder them back together right! now my rear brake light is always on & I don't know...


The front brake light switch is located on the inner face of the right handlebar switch housing. If you have too much of a gap between the switch housing and the front brake master cylinder, the brake light will stay on continously. Move the front brake master cylinder outward on the handlebars snuggly against the right handlebar switch housing. If this doesn't not solve the problem, your wiring or the switch has a problem.

Good Luck
Steve

Jun 08, 2010 | 2006 Harley Davidson FXDLI Dyna Low Rider

1 Answer

Rear brake light not workiing


There are two brake light switches. One is in the right handlebar switch housing. This is front brake light switch and is a simple push button type switch actuated by the front brake lever.

The other switch is a pressure switch and it is located in a Tee usually somewhere under the bike near the rear of the transmission. Follow the metal tube coming out of the rear of the master cylinder. It will go back towards the rear brake. Somewhere in that line there will be a tee with the pressure switch in it. If you jumper across this switch, the brake light should work. If it does work when you do this but not work when you depress the rear brake signal, replace the rear brake light switch.

Good luck
Steve

May 26, 2010 | 2000 Harley Davidson FLHRCI Road King...

1 Answer

REAR BRAKE LIGHTS DO NOT COME ONLY TAP LIGHT IS


Check for power at the turn signal switch. White wire comes from brake switch switch into the turn signal switch. The brake light switch is working because the high mount brake light is working..right? Do the turn signals work ok? if so, then the wiring is OK. The brake signal wires that come out of the turn signal switch are dark green(right) and yellow (left).

Oct 27, 2009 | 2001 GMC Safari

3 Answers

Brake lights not working even though the brake peddle is pushed down The switch still goes in and out. Fuse box has some fuses missing. The fuse box does not have a desription on every plug of what it is...


Here are the numbers on your fuseblock and fuses coresponding to the number that is on your fuse block.
1-20 amp (yellow)
Hazard flasher
2-10 amp (red)
back up lights, A/C clutch cycling Switch
3-30 amp (green)
Power windows
4-30 amp (yellow)
A/C or heater blower motor
5-20 amp (yellow)
Panel Lights, Side marker lights, Park, Taillights, Clock & radio display Intensity, License & panel lights.
#6-10 amp (red)
Stoplight, buzzers, Anti-lock brake module
#7-15 amp (lt. Blue)
Tachometer, horn & Relay
#8-8 amp (yellow)
Power Door locks
#9-10 amp (red)
Radio
#10-10 amp (red)
Rear Wheel Anti-lock module, Turn Signals
#11-20 amp (Yellow)
Windshield wiper & washers
#12-15 amp ( LT. Blue)
Cigarette Lighter
#13-5 amp (tan)
Speed Control, warning buzzers, gauges, indicator lights
#14-5 amp (tan)
Time/delay relay & under-hood light, dome light, power mirrors, readio & clock Memory, Interior lights, reading lights
#15-blank
Not used
#16-4 amp (pink)
Radio Lights & overdrive switch light 1989-91, Cluster lights, Cigarette Lighter light & as tray light, Cluster lights, A/C & heater controls.
#17-relay
Hazard Flasher warning
#18-relay
Relay
#19-Circuit breaker
#20-relay
Turn signal Flasher
#21-buzzer
Warning
#22-Relay
Horn

Aug 04, 2009 | 1991 Dodge Dakota

Not finding what you are looking for?
2007 Boss Hoss BHC-3 ZZ4 Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boss Hoss Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Mike

Level 3 Expert

4340 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

15716 Answers

Are you a Boss Hoss Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...