Question about Motorcycles

Open Question

2008 superglide custom hooking up a tach what color wire do I connect to the signal wire on tach?

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 269 Answers

SOURCE: turn signal wire colors right and left

The circuit breaks the ground to work. Both wires go to both signals, the black have two different connections to get back to the signal relay 9different paths). Take your old wires and follow back to see how the were run before.

Posted on Aug 14, 2009

wd4ity
  • 4565 Answers

SOURCE: Installing new handlebars, where are wire

One the earlier models, the handlebar connectors were down under the tank. But, Harley changes electrics every year so you never know. All I can tell you is "follow the wire".

Posted on Sep 27, 2009

DoubleClutch
  • 376 Answers

SOURCE: I am hooking up a tach on a 2009 sportster. I

It will state on the coil beside the terminals a + or -
Good luck.

Posted on Oct 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I hook the TACH sig wire on a Mercury outboard model 1150 in-line 6


Good day William,
You Connect the tach wire On The Voltage Rectifier ,
Rectifier Should Have 2 Yellow wires Connected To It Connect Tach Wire Together With One Yellow
Regards
Gordon

May 24, 2016 | Boating

1 Answer

On a 1998 chevy cavalier what color wire do i hook the green off my tach to


The green wire from the tach goes to the negative side of the coil or if its an HEI distributor it will connect to the left of the hot wire going. to the distributor.

Apr 01, 2014 | 1998 Chevrolet Cavalier

1 Answer

Speedometer/tach combo i bought from autometer cant get the speedometer or odometer to work the back of the autometer has 12 places for wires but my factory gauge only has 10.autometer has not been an


your spedometer should be hooked up via cable off the front wheel. not through wiring but use your volt meter to ensure the wire coloring didnt change in the makes of bikes

Apr 21, 2013 | Harley Davidson FLSTC Heritage Softail...

1 Answer

Put an rs82 bulldog remote starter in my 2005 town and country, and after 11 seconds it stops and re engages the remote starter and stops after 11 seconds and stops completely


It sounds like the RS82 is not getting a proper tach signal. If you are using tachless mode, the 12 volt constants may not be providing the desired signal. Recheck your connections to ensure that they are solid. The high amperage wires should be soldered. You will need to connect the tach wire if the connections are good. The tach wire can be connected to the negative side of the ignition coil's blue/brown wire or the blue/green wire at the PCM or you can use any one of the uncommon colored wire at a fuel injector.

Oct 10, 2012 | Remote Starter with Keyless Entry

1 Answer

My speedometer and turn signals and brake light quit working on 2005 Harley dyna superglide


Hi Bdthng, always check fuses and bulbs first, you could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below: Harley Davidson Wiring Diagrams and Schematics

Jul 10, 2011 | 2007 Harley Davidson FXDC Dyna Super Glide...

1 Answer

I have the alarm system hooked up, i have the remote start hooked up as well but its not turning over and starting the car. it flashes 7 times, (parking lights) do i need to install the starter inhibit...


The seven flashes of the parking lights when you attempt to remote start is the tach signal not being programmed. If you hooked up the tach wire already, turn the ignition on, press and release the programming switch three times. Turn the key off, press and hold the programming switch and start the car. Continue to hold the programming switch while the vehicle runs. The parking lights will be flashing while the tach is being programming. Hold for at least 15 seconds for a good signal. This allows the engine to "smooth out" into a normal idle rpm.
If the parking lights are not flashing, the tach is not being programmed. You may have skipped a step during the set up for the programming or, you have the wrong tach wire. If you went to a injector or coil wire, it is the uncommon wire. This means that there exists two or three wires at the injectors/coil packs. One or two of the wires are the same color at all of the injectors/coil packs and one wire is a different color at each injector/coil pack.

Mar 03, 2011 | APS787 Prestige Remote Start and Security...

1 Answer

How does the wiring go to hook the battery back up on a 2010 dyna superglide. harley davidson


The cable coming from the starter goes to the positive side of the battery. The cable coming from the frame connects to the negative side of the battery. There may be an auxillary power wire. If it's red in color, connect it to the positive side of the battery. If there is a charger pigtail, connect the red lead to the positive lead.

Good Luck
Steve

Jan 24, 2011 | Harley Davidson FXD Dyna Super Glide...

1 Answer

Turn signal wire colors right and left


The circuit breaks the ground to work. Both wires go to both signals, the black have two different connections to get back to the signal relay 9different paths). Take your old wires and follow back to see how the were run before.

Jul 15, 2009 | 2003 Harley Davidson FXSTB Night Train

2 Answers

I'm installing a harley mini tach ( 3 wire ) on my 2005 carberated fxdwg.. I just need to know is there a signal wire under the dash or do I run it to the coil? And what color is the wire.. nobody can give...


There should be a light green or violet wire coming from speedometer this is your database wire. This is were you hook up your last wire. Hope this helps, from 04-to 07 the wires are pretty much the same color.

wires from speedometer:

light green/ violet = database
black= ground
orange/white= inst power+12vdc

Jul 14, 2009 | Harley Davidson FXDWG Dyna Wide Glide...

1 Answer

Cant figure the wire hook up on a digital speedometer


Hi Mrbadco1,try calling the digital speedometer folks. Good luck

Jun 13, 2009 | 2004 Harley Davidson FXD - FXDI Dyna Super...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...