Question about 1998 Honda CBR 600 F(3)W

Open Question

I have a 1998 cbr 600 that it not running on the 2 right cylinders,i never checked for spark but i would belive thats not the problem because it fires 1-3 & 2-4,also the chock is broke and not working right, it idles rough but dont sound that bad..... possible carb problem or worst?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: honda cbr 600 wont start

hi, each lead has the specific number on it. if you do this correctly then they genrally give you an idea to where the sit in the coils( the way they bend :-) ) also i believe the coils are better off been attached to the frame once you are sure leads are in corect order and possitioned correctly in the coils.i just presumed the coils neaded earthing. make sure battery is pleny charged as a bad battery can just hinder. it is also very easy to flood the bike so just check the plugs again. if they are unusually wet then dry them off and try again . otherwise maybe try cleaning all electics.

hope this somehow helped
gavin barraclough

Posted on Apr 26, 2009

Ad
  • 6 Answers

SOURCE: my 1998 cbr 600 FW cuts out at low revs and will not

is this something that only happens when cold ? maybe you should consider taking plugs out and checking compression as piston rings could be kaput. hope this helps in some way :-)

gavin barraclough
GB Auto's

Posted on Apr 26, 2009

hotratchet
  • 952 Answers

SOURCE: cbr 600 f3 will not start

wow, 7 years without use! try to check if the fuel pump motor is still working... also check the fuel lines if its clogged.. I hope you get your bike up and running again... feel that adrenaline rush when going 100+mph.. hehehe.. have a good one bro...

Posted on May 26, 2009

  • 234 Answers

SOURCE: cbr 600

have u made sure the floats have not got stuck

Posted on Aug 02, 2009

voices122
  • 12 Answers

SOURCE: my honda cbr 600 wont start and keeps backfireing

Check your plugs. If all four are sparking then your carbs are out of sync. They will need to be re-balanced.

If you are capabable in doing this job your self, you will need a screwdriver that fits your adjuster screws and a CarbTune Carb balancer.
Remove your tank and airbox.
You should see the flaps inside your carbs. These should open when you move your throttle.
Start on the outside carbs to get them balanced with the 2 centre ones.
To start, unscrew the adjusters all the way out. then screw them in until the 2 outer carbs move at the same time as the inner 2 carbs
Once this is done then adjust the centre balancer to syncronise the 2 left hand carbs to the 2 right hand carbs.
Now if you have done this correctly, all four carbs should open at the exact same time.
If you have a Carbtune balancer, remove the plugs from the top of your inlet manifold and plug in the hoses from the carbtune balancer.
Start the engine and adjust the screws until the weights inside the Carbtune balancer all read the same.
Once done, remove the balancer, replace the plugs into the inlet manifold, refit the airbox and tank and it should run so much better.

If your not 100% confident to unertake this job yourself, take the bike to your local dealer and ask to have the carbs balanced.

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cbr600 only two cylinders seem to be firing and back fires


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system.
12. Carburetor contaminated, sticky float, plugged jets.
13. Carburetor vacuum diaphragm torn, cracked, not seated or installed improperly.
14. Multiple carburetors out of sync.
15. Fuel filter clogged.
16. Old or contaminated fuel.
17. Fuel tank vent system plugged or carb vent line closed off.
18. Gas cap diaphragm valve faulty.
19. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
20. Carburetor controls misadjusted.
21. Incorrect valve timing.
22. Valve springs floating, weak, or broken.
23. Damaged intake or exhaust valve.
24. Incompatible performance parts.
25. Control module may be in "LIMP" mode
26. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.fireblades.org/forums/honda-cbr-600/61533-f3-two-cylinders-not-working.html
Cylinder not firing CBR Forum Enthusiast forums for Honda CBR Owners
Honda CBR600F4I 2001 Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CBR600F Owner Manual

Jun 26, 2014 | 1998 Honda CBR 600 F(3)W

1 Answer

Changing spark plug's on my 1998 Honda CBR 600 f3


Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
F3 spark plug removal UPDATE CBR Forum Enthusiast forums for Honda CBR...
98 CBR 600f3 Spark Plug change
Honda CBR600F4I 2001 Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CBR600F4i Owner Manual

Feb 05, 2014 | 1998 Honda CBR 600 F(3)W

1 Answer

I don't know which spark plug wires go to which cylinders in my honda cbr 600 f3. Can you please tell me which ones are for which cylinders?


If you look on each plug lead, there should be a number 1, 2, 3 4.

Put them onto the relevant cylinders . !

Sep 07, 2011 | 1998 Honda CBR 600 F(3)W

1 Answer

My1991 cbr 600 is only running on number 3and4 cylinders


have you checked your coil pack and make sure you have correct spark to both cylinders

Mar 24, 2011 | 1991 Honda CBR 600 F(2)M

1 Answer

I got a 95 cbr 600 f3 it runs fine but idles bad and really doesnt like to start to easy i was checking the pump to see if i could here it or see if it would do anything and it didnt do anything i checked...


Talking about making it dificult for yourself, does the motor run, yes, sounds more like somethings dirty to me, when was the last service, and was the valve claerances done at that service? when were the spark plugs replaced?
Cheers Tony

Dec 09, 2010 | 1998 Honda CBR 600 F(3)W

1 Answer

How to change spark plugs on a 1998 Honda CBR 600


Remove spark plug cable from top of spark plug and use a socket set to remove spark plug and then place new spark plug and tighten it to required Torque which is specified in Repair manual for your bike

Jun 23, 2010 | 1998 Honda CBR 600 F(3)W

1 Answer

I have a 93 honda cbr 900rr. the gas is mixing with the oil. can the problem be the carbs.


Could be the carbs (difficult).
It could also be lack of spark (easy fix if you only have to replace spark plugs. Fix is more difficult if you have bad spark plug wires or a problem with the ignition system that makes the spark at the right time).


In any case, the unburned gas has to go somewhere so it runs down the cylinder wall and the piston rings will not seal well enough to keep it out.

Nov 20, 2009 | 1998 Honda CBR 900 RR Fireblade

2 Answers

Firing order


Hi and welcome to FixYa,

For and MC22, seated on the bike, the left hand ignition coil fires cylinders 1 & 4 while right hand ignition coil powers 2 & 3 cylinders.

Good luck and thank you for asking FixYa.

Nov 17, 2009 | 1998 Honda CBR 250 RR

3 Answers

CBR 600 F3 1996, stored for 4 years


It might be a good idea to flush everything out with clean oil. And maybe clean the oil filter. And clean the crankcase and stuff.

Dec 03, 2008 | 1985 Honda XR 250 R

Not finding what you are looking for?
1998 Honda CBR 600 F(3)W Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...