Question about 1990 kawasaki ZXR 250

Open Question

Carby problems Where can I find a rebuild kit for the carbs also where can I source parts for this particular import.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust carb or rebuild carb on a ryobi b42


with the price of a kit it is cheaper to get a new carby from e-bay
you can download a workshop manual from the net
go google and type in-- workshop manual for ryobi b42 trimmer --- and down load any pdf versions

Sep 10, 2016 | Ryobi Garden

2 Answers

Sitting aout 7 yrs , will run with starter fluid and gas in carb until used then stops


Hi Gene, Seems like you need to pull your carby off and unscrew the bottom half from the top, 1st sign of a needle stuck inside the seat is a dry carby There you'll find the float, push the float up and down and see if the needle above the float slides up and down from the seat, If the needle stays up then it's stuck and NOT letting the fuel into the carby, Just pull it down with your fingers to loosen it up..I hope this helps.... CHEERS..

Apr 25, 2016 | Garden

2 Answers

I have a Strikemaster 2000 ice auger with a Tecumseh engine & carb. I need a carb kit.


If you can ascertain the carb model and make you can usually get the carb kits on ebay for a lot less than you would pay at your local mower repair shop. Check it out.

Feb 25, 2016 | Cars & Trucks

1 Answer

When I pump the primer bulb, why doesn't it fill with fuel and stays collapsed?


new carbies start around $25.00 us on e-bay so get a new carby
take it to a mower shop for a service
rebuild the carby using a new carby kit

Nov 28, 2015 | Husqvarna 125 Bvx Leaf Blower Lawn Yard...

1 Answer

I've rebuit carb.new fuel pump and gas line hose on a 25 horse Johnson.will start but stalls out in a few seconds any ideas why.


adjust the mixture screw either in or out
may have to do this with a few rpms until it settles down
with the carby there are "O" rings and gaskets not shown in the break down that only the service dealers are aware of
My friend found this out after rebuilding his carby and it started and ran but would not develop enough power in gear
In frustration he took it to a service dealer who upon pulling the carby down showed him where the missing "o" rings should have been and explained that the rings are not in the overhaul kit along with some gaskets
after reassembling with the missing parts , the engine performs as new
Knowing that there is a problem I would suggest that you take the carby in to an accredited service center and discuss the problem with them as there is every possibility that although you are doing everything correctly , there may be parts missing that you are not aware of as was the case for my friend

Nov 27, 2015 | Cars & Trucks

1 Answer

Having problems after cleaning the carby on dt 175 fuel just comes out all tubes connected to it any ideas would be good


Check you needle and seed maybe needs replacing and most important is the flot level, I would start by striping the carb cleaning it and checking all the parts and jets inside clean and doing what it needs to do, like reducing petrol flow and the right time something is worn I would also replace the little rubbers if possible get a new carb kit if all else fails.

Nov 03, 2012 | Motorcycles

2 Answers

Will not run without the choke on


sounds like you may need to check / rebuild carby and check fuel lines and fuel filter , check tank breather as well

but before rebuilding carb make sure compression and spark are up to scratch and muffler is clear then make sure that the crankcases are air tight and have no air leaks from ie base gasket , c/case joints, crank seals , insulator gaskets or manifold boots or carb gaskets

this is important vacuum and pressure operate the carby diaphrams if not enough vacuum
carb wont pump / pickup fuel mix from tank

if air is leaking in the unit will typically be hard to start, or not at all, wont idle , keep stalling
require consistant mixture adjustments, or may even increase its own revs without throttle being applied , and may even run hot , and have low power


cheers

Nov 21, 2010 | Poulan Garden

1 Answer

Yes i have a hb-100 blower and when i hit the primer ball it pushes air out of the gas line but it does not **** any gas up the line back into the carberator??


sounds like the primer purge valve is faulty
but check the fuel filter and lines anyway for holes / perishing

could also be needing a carb kit installed particularly if been sitting around

might pay to fit carb rebuild kit for this machine

carb id # is stamped on the carb ie c1q or c1u ####
parts needed should be in the kit

your local outdoor power shop should be able to organise this

cheers

Sep 09, 2010 | Homelite Garden

2 Answers

I need a diagram to rebuild the carb for my 67 250 inline 6


When you buy a carb. rebuild kit it will come with the diagram chart and spec to rebuild it.

Jun 10, 2010 | Cars & Trucks

2 Answers

My truck runs for 10 sec. then shuts down


if it is a carby model you are looking at a rebuild kit, the problem is the needle and seat in the carby, i would install a needle and seat (complete carby kit if you have the time and the money) then to guarantee the job done i would install electric fuel pump if it does not alreaddy have one, this should fix the problem, hope i have helped

May 16, 2009 | 1989 Dodge Dakota 2WD

Not finding what you are looking for?
1990 kawasaki ZXR 250 Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...