Question about 2008 Husqvarna TE 450

Open Question

My TE450 Husqvarna seems to bog when maintaining a constant speed. A blip of the throttle every so often fixes it for a few minutes.

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
co7196
  • 3433 Answers

SOURCE: while maintaining constant speed engine mis-fires

Running lean

Posted on Jun 20, 2009

Ad
wayneman01
  • 301 Answers

SOURCE: hello, i find it impossible to maintain a constant

Bikes like yours with high horsepower output, a high revving engine, and relatively light weight are very sensitive when operated at low speed - and at low power settings. I have found that usually, after getting well acquainted with a particular bike, things become much easier have a fine control over. In the meantime, try running in higher - or lower gear, at that speed. Sometimes that can make constant throttle movements less necessary.

Posted on Feb 21, 2010

Testimonial: "thanks wayne , i have found that as you say using a higher gear does make the bike run smoother ,its just that it can be annoying at times. thanks bud"

nova2nv
  • 197 Answers

SOURCE: i am having trouble with my husqvarna 61 .after

Check to see if your tank vent is plugged.Fill tank full of fuel and run saw till you start to hear saw having problems,when this happens loosen fuel cap and see if it helps.Loosening the fuel cap will let air back into the tank if your vent is plugged.

Posted on Feb 22, 2010

  • 2239 Answers

SOURCE: i have a 16 in

It may well just need the carb adjusted, unfortunatley there is a special tool required the adjust the screws, the L screw on the carb may need richening up, so if you manage to get the tool unscrew it by 1/4 out ( anti cliock wise ) tool part no. 530035560

Posted on Mar 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ttr90 bogs down at high rpms


I have a ttr 90 that idles well but bogs down at full throttle. Carb is clean and has new pilot and main jets. Seems to run slightly better with intake off. Which leads me to believe the mixture is rich. No adjustment on carb. Stumped?

May 28, 2012 | Yamaha Motorcycles

1 Answer

Sportster bogs off idle


Hi Anonymous, give the nice folks at dynojet a call. Have nice day.

Feb 08, 2012 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

2008 Husqvarna TE 450 will not stay running


Hi, Lummy and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system and or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Restricted, blocked or kinked fuel line.
14. Faulty fuel pump.
15. Faulty pressure regulator.
16. Faulty or clogged fuel injectors.
17. Lean angle switch is faulty or needs adjustment.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.cafehusky.com/threads/2008-te450-wont-stay-running.82557
2008 te450 wont stay running
Husqvarna 2009 TE 310 Workshop Manual
World Wide Webshop for your Husqvarna oem parts accessories and merchandise
https://www.manualslib.com/manual/1102944/Husqvarna-2009-Te-250.html

Aug 14, 2017 | 2008 Husqvarna TE 450

1 Answer

I have a 16 in 235 Husqvarna chainsaw that starts find and runs for a few minute. then acts as if it is not gettting enough fuel as it starts to bog down while running and will not maintain idle.


It may well just need the carb adjusted, unfortunatley there is a special tool required the adjust the screws, the L screw on the carb may need richening up, so if you manage to get the tool unscrew it by 1/4 out ( anti cliock wise ) tool part no. 530035560

Mar 20, 2011 | Husqvarna Garden

1 Answer

When I first start my 99 electra glide classic, it idles at about 1k. If I then blip the throttle, the idle drops to about 400 rpm. It remains there until I ride for about 20 minutes. Then it stays at...


If your bike is fuel injected, this is typical. What is happening is the fast idle is keeping your engine running until you blip the trottle. When you do this, the fast idle relaeses the idle speed control. Once the engine gets to full operating temp, the idle speed is correct.

Good Luck
Steve

Oct 26, 2010 | 2001 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Hello, i find it impossible to maintain a constant speed (about 30mph) without the bike juddering , im having to open throttle - close throttle constantly to keep at 30. it has been back for repair and...


Bikes like yours with high horsepower output, a high revving engine, and relatively light weight are very sensitive when operated at low speed - and at low power settings. I have found that usually, after getting well acquainted with a particular bike, things become much easier have a fine control over. In the meantime, try running in higher - or lower gear, at that speed. Sometimes that can make constant throttle movements less necessary.

Feb 21, 2010 | 1998 Yamaha YZF 600 R thunder cat

2 Answers

Trigger on poulan 3314 does not control speed. Saw runs at constant speed, somewhere above fast idle.


Open the cover over the air cleaner so that you can observe the action of the throttle cable and carburetor lever. Operate the throttle--normal action is lever wide open at full throttle and lever resting on idle stop screw when throttle released. If action is restricted, disassemble the handle where the throttle trigger is located and clean out the sawdust. Recheck throttle action. The throttle cable shouldn't require lubrication. Clean the air filter and check the operation of the engine. Hope this helps!

Jan 27, 2010 | Poulan Pro 16-Inch 38 cc Anti-Vibration...

Not finding what you are looking for?
2008 Husqvarna TE 450 Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

choprboz5

Level 2 Expert

196 Answers

Joseph Hoffmann

Level 3 Expert

1709 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...