Question about 1999 Suzuki GSF 600 N Bandit

Open Question

How do you remove the speedometer from a 99 suzuki bandit

Posted by on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 22 Answers

SOURCE: suzuki bandit front brake discs

no they are different if you have a 1200 need to get them for the 1200 or the gs500e and f models or the RF900

Posted on Feb 25, 2009

  • 3567 Answers

SOURCE: suzuki gsf 1200 s bandit

Christmas comes early. Go to the site below and you can download a free PDF service manual. Yours is the 1st one in the "Suzuki GSF" section of the list. 4 or 5 below that is a PDF parts diagram with part numbers. Most manuals are in English but some are not. There is no way to be sure without doing the download. You can always delete it if in a foreign language.

Top rating due for this answer! Thanks Asel :)

Posted on May 08, 2009

  • 333 Answers

SOURCE: torque settings for crankcase suzuki bandit 600gsf

Crankcase bolt (M8)
(initial):13 N-m (1.3 kgf-m, 9.5 lb-ft)
(Final):23 N-m (2.3 kg-fm, 16.5 lb-ft)

Please leave positive feedback if you feel I have helped.

Thank you

Posted on Aug 29, 2009

  • 31 Answers

SOURCE: how to remove timing chain suzuki gsf 400 bandit

unless you have the correct tools this is something you probably wouldn't want to get involved in as you would need a camchain splitter/riveter if you drop the old pin down the can tunnel your in a world of hurt and the only way to remove the old chain in one piece is via a complete engine rebuild also while the cams are coming out you'd want to do the valve clearances at the same time, on some models it's tappet adjustment and some it's shims which requires you having a selection of different sized shims.
My advice is give it to someone who already has the equipment and pay them it'll cost you a lot less in the end.

Posted on Apr 25, 2010

  • 8909 Answers

SOURCE: how to remove spark plugs

If the plugs are very tight, use firm pressure intermittantly whilst unscrewing the plugs a bit at a time, screwing the plug back in and then out again. This, if done with a hot engine, will help to avoit damaging the head and the aluminium threads.
If the threads get damaged due to a build up of carbon on the end of the threads, Helicoils will need to be inserted. If you need helicoils, contact a quality engineering company for help, or a good garage. Don't foget to fit the correct length plugs and use "Copper Ease" on the thread to avoid this problem again
Hope that helps

Posted on Dec 14, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear wheel removal GSF1200

1200 Suzuki bandit. I have the 2002 very simple, put it on its center stand, take out the cotter pin takeoff nut . The tire and pool the axle out in the tire will drop out easy peas you lemons, greasy

Feb 23, 2015 | 2004 Suzuki GSF 1200 Bandit N

1 Answer

I have a low speed ticking sound from front end

The speedometer drive may be making a noise. Check the wheel bearings by lifting the front end and manually spinning the front wheel. See if it shakes, grinds or ticks.

Jul 16, 2014 | 2007 Suzuki Bandit 1250

3 Answers

How to replace air filter suzuki 1200 gsf bandit

- Take the seat off.
- Unscrew the two bolts holding the back of the tank.
- Remove (unscrew) the petcock handle.
- Lift the back of the tank. I'm not sure the air filter can be accessed without removing the whole tank. If you have to remove it, it just slides back and up - there are no screws in the front of the tank. Pay attention not to disconnect the hoses/wires if you are just lifting the tank, or disconnect them all if you have to take the tank off.
- Unscrew and remove the battery cover if necessary.
- Unscrew the airbox cover (two screws in top corners).
- Pull the airbox cover back and remove it. It's held at the lower end by two plastic "teeth" - no screws.
- Remove the old filter and put in the new one.
- Put everything back in reverse order.

Refer to the microfiche above for parts layout. This is a simple procedure that shouldn't take more than 30 minutes even with tank removal.

Apr 27, 2010 | 1997 Suzuki GSF 1200 Bandit S

1 Answer

Engine swop

You need a wiring diagram for a 99 and compare with the 91 and trace the power for each circuit.

Feb 14, 2010 | 1999 Suzuki GSF 1200 Bandit S

1 Answer

Speedo on a 1995 bandit stopped working

If your speedometer works by a cable coming from the front wheel, remove it at the speedometer head bottom, spin the front wheel to see if the inner cable turns, if it does, the speedometer head assembly is bad.

Nov 25, 2009 | 1996 Suzuki GSF 600 N Bandit

3 Answers

Speedometer not working

Check your speedometer gear box, it probably got bumped during removal/installation. The cable may have got pulled out. You can see the gearbox here:

Jun 15, 2009 | 2004 Suzuki VL 800 Volusia

1 Answer

Tyre pressure

32psi front, 36psi rear. thats for street riding not track ;)

May 17, 2009 | 2005 Suzuki GSF 650 N Bandit

Not finding what you are looking for?
1999 Suzuki GSF 600 N Bandit Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

75744 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides