Question about 2000 Harley Davidson FXDL Dyna Low Rider

1 Answer

What size are the large nuts on the crank and the clutch?

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Harley Davidson Master
  • 43,744 Answers

Hi Anonymous, take a ride or drive over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary and offer professional advice and assistance concerning your issue. Have a nice day.

Posted on Jun 11, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Putting a clutch together

hi there you need to take the clutch cover off after draining the oil ,remove the bolts going into the clutch basket take the springs out as well if you have the cash put in new springs when installing the clutch ,after you take the outer off then take out the plates and have acheck on size and wear ,then there should be a large nut and lock washer tap down the tab that stops the nut spinning loose then put your foot on the back brake and undo the nut this will be very tight if you have a air rattle gun this makes life a lot easier .then replacing the clutch basket it would be good sense to put a new bearing in the clutch houseing then put it back together in the oposite direction cheers hopes this helps cheers

Mar 27, 2014 | Husqvarna TE 610 Motorcycles

1 Answer

Crank has become loose

If this is a one-piece crank (both crank arms and the axle are all one piece) then you would need to tighten the bearing. This has an adjusting nut and a large locknut. There are special tools for this, but you can get by with a pipe wrench for the lock nut.
However, if this is a three-piece crank, then you probably have a loose crank arm (or two). The axle (which you cannot see) has square ends (about 1/2 inch) that are tapered toward the end (just a little smaller). The cranks have correspondingly tapered square holes. You simply have to tighten the nut or bold on the end of the axle to draw the tapered parts together tightly. There is probably a little cap covering the nut or bolt. The cap usually unscrews with a straight screwdriver. Common size for the nut or bolt is 14 mm. You will need a thin-wall socket for this, or a special crank-arm wrench. Park Tools is a great source for the special tool and lots of how-to info and videos. Good luck.

Feb 12, 2013 | Diamondback Joker 20 Boys' Freestyle BMX...

1 Answer

How do I replace the clutch on an echo hedge trimmed hc-160

the clutch attaches to the crank like a large nut but it has left hand threads so turn it like you would tighten a normal bolt

May 31, 2012 | Echo Garden

1 Answer


to remove clutch fan you need to remove upper fan shroud, you need large wrench to remove the fan clutch retaining nut to remove fan and clutch away from the engine drive belt should keep pulley from turning while loosen fan clutch retaining nut.if pulley belt turns while loosen fan clutch bolt remove drive belt use strap wrench hold pulley while you remove fan clutch bolt this procedure for checvrolet if you working on volkswagon you need spanner wrench hold the idler pulley while you use large wrench to loosen the large drive nut to fan clutch. you have to remove fan with clutch from engine then you can remove clutch from fan you can go to auto parts stores rent a spanner wrench try auto zone they rent out tools.

Jan 05, 2012 | Cars & Trucks

1 Answer

Can't remove clutch nut from a 1983 vt750c honda

Remove the large circlip from the clutch hub then remove the clutch lifter plate. Remove the other parts noted in the diagram below. Now you have access to the hub nut. It is best to use an impact driver on the nut. tombones49_159.gif

Jun 05, 2011 | Honda Hyper 4 ProQuad Chopper Motorcycles

1 Answer

Trying to remove fan clutch,which way does it turn?


Apr 01, 2011 | 2000 Chevrolet S-10

1 Answer

How do i replace the drive mechanism for a poulan pro model pp4218avx

Ok, start by removing the side cover, there will be a large plastic nut with a flip up lever, undo the nut anti clockwise, now remove the guide bar and chain which are now free, there will be a c clip and washer holding the clutch drum on, remove the clip witha suitable screw driver, remove the large washer, the clutch drum will now just pull off, there is now a small washer to remove, you will now see the clutch, there is a special tool required to remove the clutch, it fits into the two half circle cut a ways in the clutch centre, the clutch is threaded onto the crank with a left hand thread, once the tool is fitted you put a 19mm spanner on the tool and jar it off against compression. The special tool is part no. 530031112.

Feb 19, 2011 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

1 Answer

How do you remove the fan from the water pump?

after remove the 4 nuts in water pump need to remove a large nut in front of the fan.
on the back of the fan right in front of the pulley is your large nut.. grab the right sized wrench and hold the fan so it doesnt turn and crank on it. it should come off..
**** have a reverse thread**** loose to right

Jun 01, 2010 | 1996 GMC Sonoma

1 Answer

2001 blazer hi clutch does the fan clutch come off the big nut

The big nut on the clutch unscrews from the pump. You'll need to get a chain strap wrench to hold the pulley or someway to hold the pulley, and a large wrench to loosen the nut.

May 28, 2010 | 2001 Chevrolet Blazer

2 Answers

How do I get the clutch hub nut off in order to replace the clutch hub?

You would be best getting an impact driver. Just put the right size metric socket on it then strike the end with a hammer to remove or to tighten the nut. Use it also to loosen and tighten the case screws. It is the most used tool in my shop. Sears has them as does any tool store. Just get a 3/8" drive (not the 1/2" drive) and you will make stuck screws, nuts and bolts a thing of the past.

Nov 27, 2009 | 2004 kawasaki KX 250 F

Not finding what you are looking for?
2000 Harley Davidson FXDL Dyna Low Rider Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

4340 Answers


Level 3 Expert

76846 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides