Question about 2000 Yamaha YZF-R6

1 Answer

2001 R6 press the electric tart button and it buzzes

The battery evetually goes flat

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 524 Answers

Hi...

der may b several reasons

1. charge in battery may b low so try t after changing the battery
2.der may b some short circuiting occuring wen u press the start button
3.the is too much load on the starter motor which wen starting current in more picks up and gradully reduces its speed.
4.motor insulatioin may be gone so short circuiting may occur inside motor.

so plz check all these things...

Posted on Jul 04, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My r6 doesnt turn fully on disengage the headlight assembly everything turns on like normal.but then it wont turn over. I just get this buzzing sound from high and low beam relays. wiring looks fine


Hi, Sappo and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Main fuse or circuit breaker may be blown or faulty.
10. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r6-forum.com/forums/46-general-discussions/6691-2000-r6-wont-start-wut-could-problem.html
http://www.r6messagenet.com/forums/welcome-center/161248-please-help-bike-wont-start-turn-over.html
2001 Yamaha R6 won start in Sportbikes Page 1
http://martin.lipinsky.cz/r6/files/LIT-11616-21-61.pdf

Apr 28, 2016 | Motorcycles

1 Answer

I forgot the parental password on my sharp flat s teen DVD tv how do I unblock my channels


tart but pressing the "menu" button on the TV. A message should appear to input secret number. Press and hold both the "VOL (+)" and the CH DOWN on the TV set until the message disappears. This should reset all passwords and settings.

Jul 07, 2015 | Sharp Televison & Video

1 Answer

2001 r6 no power


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r6messagenet.com/forums/r6-general/155883-dead-r6-no-power-electrics.html
http://www.r1-forum.com/forums/102-00-01-r1-mechanical-help/228208-bike-not-starting-no-power-w-new-battery.html
1999 2002 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Mar 18, 2014 | 2001 Yamaha YZF-R6

1 Answer

Cannot turn the tablet on


buzzing on a tablet is not a good thing to happen, buzzing is an electrical fault. can you confirm that the tablet is the model stated, thanks

Jun 27, 2017 | Acer Iconia Tab A200

1 Answer

Yamaha r6 troubleshoot


Hi, Anonymous it should be noted that in order to "PROPERLY" diagnosis any electric starter issue it is "IMPERATIVE" that you begin with a fully charged battery 12.5 volts or better and be able to pass a proper load test, and the usual suspects are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, 12.5 volts or better,to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid has dropped more than 1/2 volt.
4. With a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 8-9 volts.
If a lower voltage is produced a proper battery load test should be performed with a load tester to validate battery integrity or battery replacement.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buy a new one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Bike won turn over Weird buzzing sound
http://www.r6messagenet.com/forums/r6-maintenance-technical/132608-buzzing-sound.html
2009 2013 YAMAHA R6 YZF R6 Service Manual Repair Manuals AND Owners Manual...
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Jan 31, 2014 | 2013 Yamaha YZF R6

1 Answer

My yamaha r6s charging system is not charging


Hi, Camryn in order to check out any main electrical system, you have to start with a fully charged battery 12.5 volts or better, and be able to pass a load test if necessary. "WARNING" never plug or unplug any electrical connector with the engine running !!!
1. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. Check the voltage drop at the battery when you hit the starter button, anything below 9 volts you might have a faulty battery.
3. Check voltage at the battery with the bike running at 3,600 RPM should be 14.3 to 14.7 volts. If you are not getting these numbers, you might have a faulty voltage regulator.
4. Make sure voltage regulator is "GROUNDED" and functioning properly, watch the video below on how to test a voltage regulator.
5. Unplug the connector to the alternator and hook your multimeter leads to the alternator (pin/socket selection does not matter) set the multimeter to AC volts, at an idle the multimeter should read 16 to 20 volts AC. at 2,000 RPM 32 to 40 AC volts, 3,000 RPM 48 to 60 AC volts. If you are not getting these numbers, you may have a faulty rotor, follow step 6
6. Set the multimeter to OHM'S, connect one lead to the alternator (any pin/socket) and the other to a ground, the multimeter should read infinity. Connect both leads to the alternator multimeter should read 0.1 to 0.2 OHM'S. If you are not getting these numbers, you have a bad stator.
7. Check all wiring in the charging circuit for worn or chaffed spots and all wiring connectors in the circuit for corroded, broken, or loose pins/sockets, which is the # 1 offender.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Yamaha R6 battery charging problem
http://www.r6messagenet.com/forums/r6-maintenance-technical/724-charging-problems-stator-rectifier.html
1999 2002 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

May 08, 2012 | 2001 Yamaha YZF-R6

1 Answer

Yamaha r6 2005 wont start.


Could do with more information maria6666.

Do the ignition lights come on when you turn the key? Battery connected/Charged
Has your red kill switch on the handlebar been knocked off?
Does the starter motor turn when you press the starter button? Battery connection/charge
Does the fuel pump relay click/or fuel pump make a whirring noise when the ignition is switched on? Battery connection prob/poor earth/fault on fuel pump relay
If when the starter button is pressed the it just clicks - battery needs charging.
Has it got enough fuel in it?
Is the fuel tap turned on?

I could go on but it would be easier if you could describe what happens when you try to start it.

Basically, it needs petrol to burn and electric to make the engine turn whilst making a spark to burn the petrol.

Have you any friends that could help you? Are you in a group of bikers/friends who you could ask?

Jun 26, 2011 | 2005 Yamaha YZF-R6

1 Answer

I'm having trouble starting my Yamaha R6. The battery seems fine, all lights turn on, but when I try to start it, I hear a buzzing/clicking sound. Is the issue with the starter relay? Or do I need to...


Hi, Arpit_kadaki it should be noted that in order to "PROPERLY" diagnosis any electric starter issue it is "IMPERATIVE" that you begin with a fully charged battery 12.5 volts or better and be able to pass a proper load test, and the usual suspects are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid can not drop more than 1/2 volt of battery voltage.
4. With a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 8-9 volts.
If a lower voltage is produced a proper battery load test should be performed with a load tester to validate battery integrity or battery replacement.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buy a new one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Bike won turn over Weird buzzing sound
Bike won start grinding clicking sound
2008 2009 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Apr 04, 2011 | 2008 Yamaha YZF-R6

1 Answer

2001 yamaha r6 knocking


Hi, Simon_keen I would love to help you with your engine or chassis noise but I just loaned my brand new pair of listening ears to your local dealer's chief technician so he could take your bike for a test ride and give you his professional opinion and estimate about your noise and repair cost. If you are a little short on "DRACHMA" and a Dealership is not on your list of fun places to visit then perhaps the list below will help soothe your worried mind so you can make an informed decision.
1. Bearings---SCREECH
2. Belts---HUM
3. Brake Rotors---BUZZ
4. Chains---RATTLE
5. Clutches---CHATTER
6. Shifting Trans---CLUNK
7. Front Forks---PLUNK
8. Rear Shocks---SQUEAK
9. Starters---CLICK
10. Solid Lifters---TICK
11. Hydraulic Lifters---TAP
12. Pistons---SLAP
13. Connecting Rods Go---KNOCK-KNOCK---who's there, it's me "*****"
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.r6-forum.com/forums/57-garage-mechanical-help/131192-engine-knock.html
http://www.r1-forum.com/forums/102-00-01-r1-mechanical-help/254730-help-weird-engine-knock.html
1999 2002 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Mar 07, 2010 | 2001 Yamaha YZF-R6

1 Answer

Bike wont charge?


Hi,

If you haven't put a new, properly charged battery already, do so.

Good Luck and Let me know,

Obe

Aug 27, 2009 | 2001 Yamaha YZF-R6

Not finding what you are looking for?

Open Questions:

See all 2000 Yamaha YZF-R6 Questions

2000 Yamaha YZF-R6 Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...