Question about 1998 Suzuki VZ 800 Marauder

1 Answer

Spring can't be replace

I have a marauder vz 800 from 2002. how can replace the springs from fork? i'd change the oil for 3 times - no 5 or 10, but 15 indicative. still soft. means have a problem with springs

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 518 Answers

If springs are inside the legs remove large nut and springs slide out,if external,remove large nuts,undo pinch bolts at bottom yoke,pull tubes out of yokes

Posted on Jul 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Im rebuilding the water pump on my 98 marauder and i got the bearings out i noticed the balls on the first bearing were facing out but the inner bearing came out and i didnt see the way the balls were


if the bearing is open on both sides it shouldn,t matter which way it goes in , if its sealed on one side and open on the other , put open side towards inside of engine . for the oil seal question , look at seal it should have a spring around lip on center lip of seal , put it towards inside of engine , if it don,t have a spring and seal is open on one side and closed on other side , put open towadrs inside of engine

Apr 11, 2013 | 1998 Suzuki VZ 800 Marauder

1 Answer

I have a 2005 honda shadow areo the front feel excesivly spongy and I have no visable leeks. looking for a solution. one shop said they can change the oil in the forks and another does not feel this would...


Have you had the bike a while? When did you start noticing this problem? Changing the fork oil should help a bit. Just like engine oil, fork oil does break down over time and should be replaced. Also, there are springs in the fork tubes that might be worn out like any other spring does over time. You can either replace the fork oil and springs, or the fork oil and add a spacer.

Aug 12, 2011 | 2005 Honda Shadow Aero

1 Answer

How much oil does a 1999 suzuki marauder 800 take for an oil change


YOUR BIKE HOLDS 2 AND 3/4 OF QUAURTS OF OIL. BUT YOU CAN FIND THE CC AMOUNT JUST BELOW THE DIPSTICK.

Jul 15, 2011 | 1999 Suzuki VZ 800 Marauder

1 Answer

How much fork oil goes in the forks of an 2001 FXD and how do I do this ? Do you have any diagrams to help me with ?




I have no diagrams for you. MAke your own as you take it apart etc and take lots of cell phone pictures if you need help remembering how to put things back together.

Table 1-6. Type E Fork Oil Amounts



MODEL OZ CC IN. MM



FXDXT 11.5 341 6.10 154.9



FXDWG 12.0 356 7.28 184.9



FXDL 10.7 316 7.20 182.9



FXD 10.6 314 6.69 169.9




Changing fork oil is a simple mater for some models and requires fork disassembly for others. Here is the procedure for all 2001 DYNA models:

2001 DYNA FRONT FORK OIL 1.18


REPLACING FORK OIL Replace front fork oil at every 20,000 mile (32,000 km) service interval and/or prior to storage.


ALL BUT FXDX & FXDXT models


Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, on FXDL models, remove the center plug from each fork cap, on all other models, remove the fork tube caps, remove the drain screws from the bottom of each fork and drain the fork oil, replace the drain screws and washers and tighten the screws

to 13-17 in-lbs (1.5-2.0 Nm) THEN see Table 1-6. and fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) as set out in the Table. THEN if apart assemble the forks as follows:


a. FXD, FXDXT, FXDWG models: install both fork tube caps and tighten them to 11-22 ft-lbs (14.9-29.8 Nm).

b. FXDL models: install center plugs and tighten until secure.


Fork oil amounts can be measured two ways: use the oz./cc measurement if fork is left in frame; use the in./mm measurement if the fork is disassembled in which case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.


Table 1-6. Type E Fork Oil Amounts for 2001 DYNA


MODEL OZ CC IN. MM

FXDXT 11.5 341 6.10 154.9

FXDWG 12.0 356 7.28 182.9

FXD 10.6 314 6.69 169.9


PART NO. SPECIALTY TOOL

HD-41177 Fork tube holder

HD-41549A Fork spring compression tool

HD-41551 Spring plate tool

HD-36583 Fork seal installer

HD-59000A Pro-level oil gauge



FRONT FORKS: FXDX & FXDXT 2.20

REMOVAL

Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, remove both front brake calipers and the front wheel, remove the front fender, remove the front fairing, remove the headlamp bracket and attach the headlamp to the frame using a rubber bungee strap, loosen the upper and lower triple clamp pinch bolts and pull the fork sides from the brackets.


DISASSEMBLY

Remove the stopper ring, remove the spring preload adjuster but DO NOT unthread the rebound adjuster from the damper rod because incorrect assembly could result in reduced adjustment range. THEN unthread the fork cap from the fork tube and allow the fork leg to drop, exposing the spring, THEN get a FORK SPRING COMPRESSION TOOL (Part No. HD-41549A) on the spring collar, turn the screws in to engage the holes in collar, compress the spring until the SPRING PLATE TOOL (Part No. HD-

41551) can be positioned between the spacer and the spring collar, THEN hold the fork bolt and compression adjuster, remove the fork bolt from the compression adjuster, remove the spring adjuster plate from the fork bolt, remove spacer, spring collar and spring, pour out the fork oil by pumping the fork leg and rod 8-10 times or until rod the moves freely. THEN position fork slider in vise using a FORK TUBE HOLDER such as (Part No. HD-41177) to avoid damage. THEN remove the socket head bolt, remove the damper from the fork tube, remove the cover from the slider, remove seal and stopper ring, pull the fork tube out of the slider, remove the oil seal, spacer and guide bushing from the fork tube.


CLEANING AND INSPECTION

Measure the fork spring free length and replace the spring if it is shorter than 17.00 in. (431.8 mm), check the fork tube and the slider for score marks, scratches or abnormal wear, check the slide and guide bushings for excessive wear or scratches, set the fork tube on V-blocks and measure runout which should not exceed 0.008 in. (0.2 mm).


ASSEMBLY

Coat the oil seal with TYPE E FORK OIL, before installing the slide bushing and guide bushing, lubricate them with fork oil, THEN install the guide bushing and the spacer seal noting that the guide bushing opening must be oriented to the side and NOT to the front or rear, THEN slip the slider into the fork tube, place the slide bushing over the fork tube until it rests on the slider, drive the guide bushing with the spacer seal into the slider, lubricate a new oil seal with TYPE E FORK Oil, drive the oil seal into the slider using FORK SEAL INSTALLER (Part No. HD-36583). install the stopper ring and dust seal, (if the rebound adjuster was removed from the damper rod bottom the lock nut on the threaded portion of damper rod, holding a thumb on the detent spring and ball, back out (turn counterclockwise) the rebound adjuster to the last "click." and then turn down (clockwise) 17 "clicks", thread the rebound adjuster onto the damper rod until the adjuster stops at maximum thread engagement (but do not force it), thread the locknut onto the damper rod up until it contacts the base of the rebound adjuster and tighten it in place), THEN holding the slider in a vise while being careful not to damage it. install the damper tube into the fork tube and tighten the socket screw and washer to 22-29 ft-lbs (29.8-39.3 Nm). THEN pour half the TYPE E FORK OIL into the fork tube, slowly pump the damper rod 10 or more times, position the damper rod in the fully bottomed position and pour the remaining amount of TYPE E FORK OIL into the fork tube. THEN using a PRO-LEVEL OIL GAUGE (Part No. HD-59000A) or similar adjust the oil level to 5.04 in. (128 mm). THEN carefully clean and install the spring, the spring collar, and the spacers with the sharp edge created when they were stamped out when manufactured, facing the collar. THEN using a FORK SPRING COMPRESSION TOOL such as (Part No. HD-41549A) push spring collar down and place a SPRING PLATE such as (Part No. HD-41551) between the spacer and the spring collar, install the fork cap and tighten it against the rebound adjuster to 22-29 ft-lbs (29.8-39.3 Nm). THEN tighten the fork cap onto the fork tube to 11-22 ft-lbs (14.9-29.8 Nm), install the spring adjuster plate, replace the O-rings on the spring preload adjuster and lubricate them with fork oil. THEN install the spring preload adjuster and the stopper ring and carefully drive the slider cover into the slider.


INSTALLATION

Insert both fork side assemblies up through the fork stem and bracket and upper bracket and tighten the fork stem bracket pinch bolt(s) to 30-35 ft-lbs (40.7-47.5 Nm). Then re-install the headlamp bracket, install the front fender, install the front wheel and the brake caliper When the motorcycle is again ready for the road adjust the headlamp and road test the motorcycle.






Feb 10, 2011 | Harley Davidson FXD Dyna Super Glide...

1 Answer

How do you remove the forks on a 2001 fxd superglide






Hopefully you will glean all you need to know from this but if you want or need more information or more FXD specific information PLEASE H

Hopefully the information below will be okay BUT if you need any more or any more specific information please post a comment and describe what you want/need.

REPLACING FORK OIL Replace front fork oil at every 20,000 mile (32,000 km) service interval and/or prior to storage.


ALL BUT FXDX & FXDXT models


Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, on FXDL models, remove the center plug from each fork cap, on all other models, remove the fork tube caps, remove the drain screws from the bottom of each fork and drain the fork oil, replace the drain screws and washers and tighten the screws

to 13-17 in-lbs (1.5-2.0 Nm) THEN see Table 1-6. and fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) as set out in the Table. THEN if apart assemble the forks as follows:


a. FXD, FXDXT, FXDWG models: install both fork tube caps and tighten them to 11-22 ft-lbs (14.9-29.8 Nm).

b. FXDL models: install center plugs and tighten until secure.


Fork oil amounts can be measured two ways: use the oz./cc measurement if fork is left in frame; use the in./mm measurement if the fork is disassembled in which case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.


Table 1-6. Type E Fork Oil Amounts for 2001 DYNA


MODEL OZ CC IN. MM

FXDXT 11.5 341 6.10 154.9

FXDWG 12.0 356 7.28 182.9

FXD 10.6 314 6.69 169.9


PART NO. SPECIALTY TOOL

HD-41177 Fork tube holder

HD-41549A Fork spring compression tool

HD-41551 Spring plate tool

HD-36583 Fork seal installer

HD-59000A Pro-level oil gauge



FRONT FORKS: FXDX & FXDXT 2.20

REMOVAL

Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, remove both front brake calipers and the front wheel, remove the front fender, remove the front fairing, remove the headlamp bracket and attach the headlamp to the frame using a rubber bungee strap, loosen the upper and lower triple clamp pinch bolts and pull the fork sides from the brackets.


DISASSEMBLY

Remove the stopper ring, remove the spring preload adjuster but DO NOT unthread the rebound adjuster from the damper rod because incorrect assembly could result in reduced adjustment range. THEN unthread the fork cap from the fork tube and allow the fork leg to drop, exposing the spring, THEN get a FORK SPRING COMPRESSION TOOL (Part No. HD-41549A) on the spring collar, turn the screws in to engage the holes in collar, compress the spring until the SPRING PLATE TOOL (Part No. HD-

41551) can be positioned between the spacer and the spring collar, THEN hold the fork bolt and compression adjuster, remove the fork bolt from the compression adjuster, remove the spring adjuster plate from the fork bolt, remove spacer, spring collar and spring, pour out the fork oil by pumping the fork leg and rod 8-10 times or until rod the moves freely. THEN position fork slider in vise using a FORK TUBE HOLDER such as (Part No. HD-41177) to avoid damage. THEN remove the socket head bolt, remove the damper from the fork tube, remove the cover from the slider, remove seal and stopper ring, pull the fork tube out of the slider, remove the oil seal, spacer and guide bushing from the fork tube.


CLEANING AND INSPECTION

Measure the fork spring free length and replace the spring if it is shorter than 17.00 in. (431.8 mm), check the fork tube and the slider for score marks, scratches or abnormal wear, check the slide and guide bushings for excessive wear or scratches, set the fork tube on V-blocks and measure runout which should not exceed 0.008 in. (0.2 mm).


ASSEMBLY

Coat the oil seal with TYPE E FORK OIL, before installing the slide bushing and guide bushing, lubricate them with fork oil, THEN install the guide bushing and the spacer seal noting that the guide bushing opening must be oriented to the side and NOT to the front or rear, THEN slip the slider into the fork tube, place the slide bushing over the fork tube until it rests on the slider, drive the guide bushing with the spacer seal into the slider, lubricate a new oil seal with TYPE E FORK Oil, drive the oil seal into the slider using FORK SEAL INSTALLER (Part No. HD-36583). install the stopper ring and dust seal, (if the rebound adjuster was removed from the damper rod bottom the lock nut on the threaded portion of damper rod, holding a thumb on the detent spring and ball, back out (turn counterclockwise) the rebound adjuster to the last "click." and then turn down (clockwise) 17 "clicks", thread the rebound adjuster onto the damper rod until the adjuster stops at maximum thread engagement (but do not force it), thread the locknut onto the damper rod up until it contacts the base of the rebound adjuster and tighten it in place), THEN holding the slider in a vise while being careful not to damage it. install the damper tube into the fork tube and tighten the socket screw and washer to 22-29 ft-lbs (29.8-39.3 Nm). THEN pour half the TYPE E FORK OIL into the fork tube, slowly pump the damper rod 10 or more times, position the damper rod in the fully bottomed position and pour the remaining amount of TYPE E FORK OIL into the fork tube. THEN using a PRO-LEVEL OIL GAUGE (Part No. HD-59000A) or similar adjust the oil level to 5.04 in. (128 mm). THEN carefully clean and install the spring, the spring collar, and the spacers with the sharp edge created when they were stamped out when manufactured, facing the collar. THEN using a FORK SPRING COMPRESSION TOOL such as (Part No. HD-41549A) push spring collar down and place a SPRING PLATE such as (Part No. HD-41551) between the spacer and the spring collar, install the fork cap and tighten it against the rebound adjuster to 22-29 ft-lbs (29.8-39.3 Nm). THEN tighten the fork cap onto the fork tube to 11-22 ft-lbs (14.9-29.8 Nm), install the spring adjuster plate, replace the O-rings on the spring preload adjuster and lubricate them with fork oil. THEN install the spring preload adjuster and the stopper ring and carefully drive the slider cover into the slider.


INSTALLATION

Insert both fork side assemblies up through the fork stem and bracket and upper bracket and tighten the fork stem bracket pinch bolt(s) to 30-35 ft-lbs (40.7-47.5 Nm). Then re-install the headlamp bracket, install the front fender, install the front wheel and the brake caliper When the motorcycle is again ready for the road adjust the headlamp and road test the motorcycle.

Oct 01, 2010 | 2001 Harley Davidson FXD Dyna Super Glide

1 Answer

What is the specs for the fluid that the forks use


Best is to use recommended OEM fork oil in the SAE10 or SAE15 range like Castrol Fork oil-10 or Fork oil-15, as number gets higher so is the viscocity and harder it on rebounding. When filing the fork do not over fill as it would make the fork response very stiff and blow out your seals. Good enough free advise?

May 03, 2010 | 1997 Suzuki VZ 800 Marauder

3 Answers

I need to know the oil capacity of the front forks on my 1999 Suzuki Marauder VZ800.


FORK OIL
• Place the front fork vertically without spring.
• Compress it fully.
• Pour specified front fork oil up to the top level of the outer
tube.
Capacity (each leg): 490 ml (16.6/17.3 US/lmp oz)
99000-99044-L01: SUZUKI FORK OIL L01
or an equivalent fork oil
• Move the inner rod slowly with the special tool ten times and
more until no more bubbles come out from the oil.
09940-52841: Inner rod holder
NOTE:
Refill front fork oil up to the top of the outer tube so that bubbles
are visible while bleeding air.
• Refill specified front fork oil up to the top level of the outer
tube again. Move the outer tube up and down several strokes
until no more bubbles come out from the oil.
• Keep the front fork vertically and wait 5 – 6 minutes.
NOTE:
* Always keep oil level over the cartridge top end, or air may
enter the cartridge during this procedure.
* Take extreme care so as to pump out air completely.
• Hold the front fork vertically and adjust fork oil level with the
special tool.
NOTE:
When adjusting the fork oil level, compress the outer tube fully
without the fork spring.
Fork oil level: 153 mm (6.02 in)
09943-74111: Front fork oil level gauge

Dec 18, 2009 | 1998 Suzuki VZ 800 Marauder

1 Answer

97 suzuki marauder fork seals problem


Normally no. If the fork seals are leaking when you ratchet the front down on the trailer your seals were bad prior to that. If you are talking about the straps being wrapped around the forks the only thing that they would contact would be the dust covers. The fork seals are actually down inside the fork about 1/4 inch. Have a good day

Aug 12, 2009 | 1997 Suzuki VZ 800 Marauder

1 Answer

Ohlins spring Inserts, Front Forks - BMW F800GS


you are right in the removal and replacement of the springs, my tip so you dont have to change the oil is when you are removing the springs nip your fingers on 1 section of the spring and turn the spring in your fingers like you are unscrewing a bolt.any oil loss will be neglible. oil is 270mls per leg if you want to change it.

Apr 17, 2009 | 2008 BMW F 800 GS

2 Answers

Front forks suspenion


It could be old oil or it could be spring tension. The easiest way to check which one is change the fork oil. If it still does not perform to your satisfaction, replace the springs. I would not expect the springs to wear out before 40,000 miles under normal usage for this bike. You should be changing the fork oil at least every two years, yearly would be better.

Jan 10, 2009 | 2000 Honda CB 250 Nighthawk

Not finding what you are looking for?
1998 Suzuki VZ 800 Marauder Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...