Question about Motorcycles

1 Answer

I have a 2001 yamaha blaster and when it isnt in gear it will rev up fine but u can tell it is loading up and running really ritch. When i put it in gear it is really boggy and it doesnt run right. Can u tell me how i can fix this

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 37 Answers

Clean carb out with carb anf=d choke prolly varnsihed up if that doesnt work then replace carb

Posted on Jul 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1986 yamaha virago 1100..when I first start the bike and put it into gear it dies out...when I rev it to 7000 rpm it goes into gear and is fine for the day until the next day


Hi, Floyd and the usual suspects are:
1. Idle circuit and transfer ports clogged.
2. Air fuel mixture adjustment too lean.
3. Pilot jet clogged.
4. Faulty accelerator pump.
5. Float level too low.
6. Float bowl contaminated old fuel, water, dirt, rust, etc.
7. Float bowl vent or overflow tube clogged.
8. Fuel flow to carburetor restricted.
9. Intake manifold leak.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Re dies when put in gear Road Star Forum Yamaha Road Star
Engine dies when put into Gear
Stalls when put in first gear
Yamaha 1986 XV1000 Service Manual

Aug 04, 2016 | Yamaha Motorcycles

1 Answer

2001 buick century runs fine when in park and nutral i can put it in drive and sometime i can go 10k sometimes only get 1k the it starts spudering and wont rev up but will idle fine put it in nutral and...


I think you have an engine speed sensor fault. its not reading the engine speed or the motion speed. needs these two to change speed and ( gear). one is connected to the abs unit and the other is on the engine. usually if they both go its down to the gear box ecu. you can check if you have it on a ecu reader. will have fault codes or not be read at all.

Mar 16, 2014 | 2001 Buick Century

1 Answer

Yamaha xt 600e 1995. won't rev above 4000 under


sounds like it may be running out of gas under aload it might be carb trouble

Jul 28, 2010 | 1995 Yamaha XT 600 E

1 Answer

YAMAHA BLASTER-Only have gears 4th, 5th and neutral?


sounds like your going to have to split the casses to fix trany to me. sorry the same thing hapened to my 2001 blaster.

Jun 07, 2010 | 2003 Yamaha YZ 250

1 Answer

I have a 2001 Yamaha 200 blaster 4 wheeler. Starts fine but bogs down when you throttle up it seems to be loading and will never throttle all the way up. It acts like it's not getting enough fuel. I...


You have to adjust the jets on the carb, theres a high and low jet, Turn them both all the way in ( dont force them) just turn until they stop, now losen each one in 1/4 intervals and try running it,

Apr 04, 2010 | 2001 Yamaha TW 125

1 Answer

Yamaha yg4000d generator Surges in the economy mode!


Economy mode is not really meant for use when you are working, more like when you are idling and using only a very small load, it must be run in Normal mode when driving the Normal load. As the Engines Rev's are "Tied" to the "Draw" from the "Outlet". More draw, the higher the rev's need to be, but in economy mode,it is Governed, and cannot Rev up enough to supply full power.

Mar 02, 2010 | Reliable Yamaha YG4000D 4000 watts/33.0...

3 Answers

2001 yamaha blaster clutch doesnt disengage and clutch cable is good and moves at the housing


Remove clutch cover and check to see if clutch is actually disengaging. Either it is not hooked up properly or it is broken.

Oct 11, 2009 | 2001 Yamaha TW 125

1 Answer

2001 blaster losses power under a load.


check the compression and if thats good, remove the air filter and try to start. or possible air fuel jet needs adjusting.

May 06, 2009 | Yamaha YZ 250 Motorcycles

1 Answer

Yamaha blaster backfire badly


well i have had the same problem and it was a gear on the right side of the motor. the clip came off and the motor died. i did get it started to get it home but it backfired really bad the entire time. put the gear back on and has ran like a raped ape ever since. hope this helps.

Apr 03, 2009 | Sport & Outdoor - Others

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...