Question about 2006 kawasaki KX 450 F

1 Answer

The easiest way to get into the gear box, broke my gear lever on a rock and the gears are not engaging as they should

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • kawasaki Master
  • 1,508 Answers

It sounds like you have bent the gear shaft.
Remove the right hand side engine cover, and probably the clutch as well. The gear shaft can then be unhooked from the selecter drum and pushed out,(the shaft goes right through the engine), this may be dificult if the gear stick end is very bent,when its removed dont try to straighten it, get a new one, and a new seal and rhs gasket. 2006 ?probably old enough to fit a new water pump seal while the cover is off

Posted on Jun 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New gear shift lever fitted, now cant get it out of low box when low gear is engaged without turning off the engine, grates loudly.


Gear shift grommets/bushings may be worn or not aligned properly. If grinding, gear is not fully engaged. Check above items to correct, if doesn't correct, may have transmittion problem.

Nov 24, 2015 | Jeep 2004 Grand Cherokee Overland

1 Answer

Any adjustment for hino dutro tipper pto.


When engaging the pto it is important that you have the clutch disengaged so that the pto gear is not spinning in the box.before it engages.
The pto gear runs off the counter shaft of the gear box and is spinning all the time the engine is running
when engaging the pto ,you are physically engaging a gear ( like selecting 1st gear) so you have to stop the counter shaft spinning so that the pto gear will engage with slashing

Jun 14, 2015 | Garden

1 Answer

Gears seem to want to slip out and make a winning noise in certain gears too is my gearbox done for or is it more likely clutch it's Audi a3 with 130000 on the clock and clutch is very high too any...


gears slipping out will be indicated by the gear lever jumping into neutral.This can be from incorrect rear engagement from a loose worn pivot in the gear lever tower or something stopping the gear lever from moving properly.. Clutch problems are indicated by --going to the floor. crashing 1st gear, engines rpm s climbing without an appreciable vehicle speed increase. If there is a fault in the gear box it will be only in the gear engaged (missing teeth-chipped ) and not all gears. If it is a bearing then there will be no noise in 4th gear
Boxes are repairable as mostly it only needs that faulty part to be replaced

Dec 22, 2014 | Audi A3 Cars & Trucks

1 Answer

Reverse gear not working in my renault clio 2004


IF all other gears work as designed then the problem will not be the clutch but in the gear box. The only thing that you would have removed in the gear box is the gear lever or the gear level turret on top of the box. recheck this area to ensure that you have got the lever in the selector rails correctly and that the reverse rail is not out of line with the cross section of the others.. Use a big screw driver to pull it out of gear to align across the slot.

Dec 23, 2013 | Renault Clio Cars & Trucks

1 Answer

T56 6Sp manual not engaging, gear lever sloppy


Check and bleed the clutch system. If the clutch is working correctly there will be no clashing of the gears during selection or attempted selection. Pull the gear lever out of the turret section of the gear box and see if the pin in the side that the lever pivots on is still intact. If ok undo the turret section of the box and ensure that the plastic cup on the end of the lever is still in place . There is normally a small cup that fits over the end of the lever that takes the gear noise out of the gear lever and it also takes up the clearance between the end and the slots in the selector rails.

Dec 08, 2013 | Cars & Trucks

1 Answer

Reverse on my gmc envoy not working


This can be due to few reasons but the most important can be as follows:

1. If can be a mis-alignment of the gear lever to the gear box as normally the reverse gear is always engage with more movement . so a change of postion or setting can alter the notch settings and refuse to engage properly.
2. Secondly the fault within the gear box, if there is a linkage or counter wheel/gear setting within it will not mesh or engage as the setting would be altered.
3. finally gaps or bush failures in the gear lever, linkages or the gear box will make the movement restricted and hence not engage.
You need to check on all the above. Thank You.

Sep 24, 2011 | GMC Envoy Cars & Trucks

1 Answer

I have a Peugot 406 Diesel estate (R), unable to engage any gears and gear lever loose and floppy. Can't drive the car at all. Any suggestions?


Gear Linkage from the gear lever to the gearbox may have come off unless the lever goes directly into the top of the box

Sep 27, 2010 | Peugeot 405 Cars & Trucks

1 Answer

06 ford focus 5spd. no 1st, 3rd, or 5th gear.


It sound like the gear linkage isn,t set up right, you wouldn,t always be able to engage a gear unless you rocked the car.

Aug 25, 2009 | 2006 Ford Focus

1 Answer

Backing up with reverse gear bike just stopped. It seems now like the transmission is in gear, but won't shift. The reverse lever is stuck in the engaged position, and I finally had to shut it off and now...


Pull out on the lever and push it toward the front of the bike, hard if necessary. Rock the bike while pushing. If the bike comes out of gear it should start. The bike will not start while the lever is up.
Probably need to replace the switch behind the lever. Don't test it, just replace it.

Jun 08, 2009 | 1996 Honda GL 1500 SE Gold Wing

1 Answer

97 1100 shadow spirit gear lever


Start the first and then go threw the gears. You always need the motor running to go threw the gears or rock the bike back N forf.And if they do not work leave it alone try another dealer.

Mar 20, 2009 | 1997 Honda VT 1100 C Shadow Spirit

Not finding what you are looking for?
2006 kawasaki KX 450 F Logo

152 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...