Question about 1990 Honda CBR 600 F(1)L

1 Answer

Torque settings Is it neccesary to use a torque wrench to fit the drive sprockets on a 1990 CBR 600 FL and if so do you know what the settings are

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

Torque wrench is not needed, just tightne the bolts securely and fold over the locking tabs(if equipped) if it does not have locking tabs a little bit of BLUE thread locker is a good idea. Be sure to use blue( removeable) and not red ( almost not removeable without heat) so you can get the sprocket off next time.

Posted on Jun 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Honda CBR 929 RR Fireblade front sprocket torque specs


Hi, Paddy for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
torque spec for front sprocket CBR Forum Enthusiast forums for Honda CBR...
http://www.fireblades.org/forums/honda-fireblade/47105-front-sprocket-torque-question.html
2000 2001 Honda CBR929RR Fireblade Service Manual Moto Data Project
http://www.partsfish.com/page/oem-parts-for-honda
Honda CB Owners Manuals

Apr 19, 2013 | 2001 Honda CBR 929 RR Fireblade

1 Answer

Need torque setting to fit sprocket cover bolts on 2011 softail std


You need a quarter inch drive inch pound torque wrench

Mar 13, 2013 | Motorcycles

1 Answer

1993 Honda CBR 600 F(2)P torque specs for cam journal caps


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.fireblades.org/forums/honda-cbr-600/103495-f293-tightening-torques.html
1993 Honda CBR 600 2 torque specs for cam journal caps Google Search
Honda CBR600F4I 2001 Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda CBR600F4i Owner Manual

Jan 08, 2013 | 1993 Honda CBR 600 F(2)P

1 Answer

How can i reach a torque setting of 305nm when my wrench only reaches a max of 200nm please any one help i am thinking that it can be done in 2 stages yes or no


It is possible to use a simple torque wrench extension bar, which fits onto the square drive of the torque wrench.
http://www.dmctools.com/Products/torque_conversion_charts.html
At the other end of the extension bar is a male square drive for the socket. This increases the leverage of the torque wrench by a ratio which is the total length of the wrench plus bar divided by the length of the torque wrench only. You multiply the torque reading by this ratio.
Note that NO increased torque is obtained by fitting an extension on the handle end of the torque wrench. The applied torque will still be the same as the torque wrench reading in this case.
Then there is a more expensive tool, a torque multiplier. These are often fitted to the output shafts of winches etc, and consist of a small gearbox which fits on the square drive of the torque wrench. On the other side is a male square drive for the socket.
http://www.tjtools.com.au/torquemultiplier.htm
They are geared in various multiplier ratios from 4:1 to as much as 40:1. On the gearbox casing is a reaction bar which is braced against something to keep it in place as the torque is applied.
They are expensive but you can hire them also.

Mar 16, 2012 | 2005 Ford Falcon

1 Answer

Ifailed to get on tdc before removing old timing belt how do I get back in time so Icanreplacebelt.


This is the complete procedure from the service manual on how to replace the timing belt start to finish, start over to assure u get it right, if u mess up the engine will be damaged

Removal for 1.6L engines : ONLY 2006 to 2009 CARS


Engine removal is not required for this procedure.

1.Remove the engine cover.

2.Remove the RH front wheel.

3.Remove the 2 bolts and RH side cover.

4.Temporarily loosen the water pump pulley bolts.

5.Remove the alternator drive belt

6.Remove the air conditioner compressor drive belt

7.Remove the power steering pump drive belt

8.Remove the 4 bolts and water pump pulley.

9.Remove the 4 bolts and
timing belt2_bing.gif upper cover

10.Turn the crankshaft pulley, and align its groove with timing mark "T" of the timing belt cover. Check that the timing mark of camshaft sprocket is aligned with the timing mark of cylinder head cover. (No.1 cylinder compression TDC position)

11.Remove the crankshaft pulley bolt and crankshaft pulley

12.Remove the crankshaft flange

13.Remove the 4 bolts and timing belt lower cover

14.Remove the timing belt tensioner and timing belt.

15.Remove the bolt and timing belt idler

16.Remove the crankshaft sprocket

17.Remove the cylinder head cover.

(1)Remove the wire harness bracket

(2)Remove the ignition coil.

(3)Remove the PCV (Positive Crankcase Ventilation) hose and the breather hose from the cylinder head cover

(4)Remove the engine cover bracket

(5)Loosen the cylinder head cover bolts and then remove the cover and gasket.

18.Remove the camshaft sprocket.

Hold the portion of the camshaft with a hexagonal wrench, and remove the bolt with a wrench and remove the camshaft sprocket.

INSTALLATION:

1.Install the camshaft sprocket and tighten the bolt to the specified torque.

(1)Temporarily install the camshaft sprocket bolt

(2)Hold the portion of the camshaft with a hexagonal wrench, and tighten the bolt with a wrench
Tightening torque :78.5 ~ 98.1N.m (8.0 ~ 10.0kgf.m, 57.9 ~ 72.3lb-ft)



2.Install the cylinder head cover.

(1)Install the cylinder head cover and bolts
Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

(2)Install the engine cover bracket

(3)Install the PCV(Positive Crankcase Ventilation) hose and breather hose to the cylinder head cover.

(4)Install the ignition coil.

3.Install the crankshaft sprocket

4.Align the timing marks of the camshaft sprocket and crankshaft sprocket with the No.1 piston placed at top dead center and its compression stroke.

5.Install the idler pulley and tighten the bolt to the specified torque.

Tightening torque :42.2 ~ 53.9N.m (4.3 ~ 5.5kgf.m, 31.1 ~ 39.8lb-ft)

6.Temporarily install the timing belt tensioner

7.Install the belt so as not give slack at each center of shaft. Use the following order when installing timing belt.
Crankshaft sprocket →idler pulley →camshaft sprocket →timing belt tensioner

8.Adjust the timing belt tension.

(1)Loosen the tensioner pulley mounting bolt and apply tension to the timing belt.

(2)After checking the alignment between each sprocket and each timing belt tooth, tighten the mounting bolt and one by one.

Tightening torque :19.6 ~ 26.5N.m (2.0 ~ 2.7kgf.m, 14.5 ~ 19.5lb-ft)

(3)Then recheck the belt tension.
Verify that when the tensioner and the tension side of the timing belt are pushed in horizontally with a moderate force [approx. 49N (11lb)], the timing belt cog end is aprox. 1/2 of the tensioner mounting bolt head radius (across flats) away from the bolt head center.

4)Timing belt tension measuring procedure
(by a sonic tension guage)
Rotate crankshaft in clockwise direction to set 1st piston on top dead center (TDC) and rotate crankshaft in counterclockwise to 90° then measure the belt tension in the middle of tension side span (in arrow direction of above illustration) by free vibration method.


9.Turn the crankshaft two turns in the operating direction (clockwise) and realign crankshaft sprocket and camshaft sprocket timing mark.


10.Install the timing belt lower cover with 5bolts

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

11.Install the flange and crankshaft pulley, and then tighten crankshaft pulley bolt. Make sure that crankshaft sprocket pin fits the small hole in the pulley.

Tightening torque :137.3 ~ 147.1N.m (14.0 ~ 15.0kgf.m, 101.3 ~ 108.5lb-ft)

12.Install the timing belt upper cover with 4 bolts.

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

13.Install the water pump pulley and 4 bolts.

14.Install the power steering pump drive belt

15.Install the air conditioner compressor drive belt

16.Install the alternator drive belt

17.Install the RH side cover with 2 bolts

18.Install the RH front wheel.


Tightening torque :88.3 ~ 98.1N.m (9.0 ~ 10.0kgf.m, 65.1 ~ 72.3lb-ft)

19.Install the engine cover with bolts.


Tightening torque :3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3lb-ft)

May 20, 2010 | 2006 Kia Sorento

1 Answer

How to install no cut frame sliders on 2005 honda cbr 600rr


One at a time, Make sure to use a manual and torque wrench set to the right value.

Feb 06, 2010 | 2005 Honda CBR 600 RR

1 Answer

How to install timing belt on 1998 vw beetle


Instructions
Things You'll Need: · Set of quarter-inch drive sockets Quarter-inch drive ratchet Set of half-inch drive sockets Half-inch drive air gun Set of metric wrenches Special tools for holding camshaft timing #2065-A and injection pump #2064

Step 1

Remove the accessory drive belts and the accessory drive belt tensioner. Remove the upper timing belt cover and the valve cover. Turn the crankshaft clockwise until the No.1 cylinder is atop, dead center, with the flywheel timing marks aligned.

Step 2

Install the special tool setting bar (#2065-A) on the rear of the camshaft. If it does not fit, turn the crankshaft once more and line up the timing marks again in the hole of the transmission housing.

Step 3

Insert locking pin #2064 into the injection pump to hold it in position. Remove the crankshaft pulley bolts, the crankshaft pulley and the lower timing belt cover. Loosen the tensioner pulley nut and allow the tensioner to move away from the belt. Loosely tighten the nut to hold the tensioner out of the way. Remove the top guide pulley and the timing belt.

Step 4

Make sure that the timing mark on the flywheel is lined up and that the camshaft setting bar and injection locking pin are in place. Loosen the camshaft bolt a half turn and tap the sprocket with a soft mallet to loosen it off its taper. The sprocket should move freely. Install the top guide pulley and torque to 18 foot pounds of torque.

Step 5

Install the new timing belt, starting on the right side and working counterclockwise. Keep the tension on the right nontensioned side. Loosen the tensioner pulley nut. Using the two-pin wrench, turn the tensioner pulley clockwise until the notch and raised mark are aligned. Torque the tensioner pulley nut to 15 foot pounds of torque. Make sure the flywheel timing mark is still aligned.

Step 6

Torque the camshaft bolt to 33 foot pounds of torque. Remove the locking pin from the injection pump and remove the camshaft setting bar. Turn the crankshaft two turns and check the alignment on the flywheel. Make sure that the setting bar can be inserted easily and that the injection pump locking pin can be inserted. Install all components in reverse order of removal and torque the crankshaft bolt to 18 foot pounds of torque.

My Recommendation - Pay an authorized VW mechanic $500 to replace the timing belt water pump an tensioner, and sleep better knowing that the job was done right. Just too many places for a novice car mechanic to screw up. jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); });

Oct 06, 2009 | 1998 Volkswagen Beetle

2 Answers

How do I replace the serpentine belt on my 2000 Plymouth Breeze 2.4l engine?


the tensioner is on the alternator there is usually a cover over it you need to loosen the 2 screws on the alternator and turn the "adjuster" screw till the belt is loose enough to come off note the whay it is run then install and tighten the new belt it must be very tight or it will slip

Sep 14, 2009 | Plymouth Breeze Cars & Trucks

Not finding what you are looking for?
1990 Honda CBR 600 F(1)L Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...