Question about 2008 Yamaha YZF-R125

1 Answer

It cloncks through the gears and is very heavey to change gear

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Check ur chain ya nob

Posted on May 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No powersteering and lift


you have to be more specific here I do not understand what you are trying to say on here and to get help from someone you have to tell us what you have and exactly what you problem is to get help

Nov 25, 2014 | Cars & Trucks

2 Answers

How do i disengae from four wheel drive


At best as I know the 2005 Prado is all time 4WD vehicle.
Is the engine running ? Can you shift the gears ?
May be something is broken in the drive train...
As a suggestion you can go home by locking the centre differential, proceeding at low speed and checking for noises .
Pls. let me know if it helps...

Apr 27, 2014 | 2005 Toyota LandCruiser Prado

1 Answer

My 87 ford Turbo Coupe has a difficult time going into 3rd all other gears are fine


sounds like its bulk rings in gear box, they spin the gears ready as u change gear when they wear the gears are not spun enough to select u probably need to over hall gear box , to help u change gear for now double d clutch, whats this as u want to change gear push clutch down move out gear release.. clutch pushdown again put in to gear use this with each gear un need to change what this does is spin gear ready for u as if bulk ring had done it for u if u are good u can just change gear but have to b good for this

Nov 12, 2013 | 1987 Ford Thunderbird

1 Answer

The gears are not changing to the right gear but i tried to change the gears to see if it will change back where it should be but it didnt. on my handle bars gears dile is saying 3 and 7 but the gears are...


Release your gear selector cables; position your chain on the 1st.or lowest gear
for both the derailer and, pedal gears.
Adjust your cables tighten and, test (some bikes use the highest gear to adjust from.

Jul 03, 2011 | Mongoose Exile 26 Men's Full-Suspension...

1 Answer

Clutch


It does sound like a clutch, but deserves to be more thouroughly checked out, Does the clutch pedal feel normal? is there a little free-travel at the top of the pedal stroke? do you see oil dripping under the car?
Clutches usually go out slowly, they start to slip under heavey load first, then gradually slip even under light loads in low gears. If an axle was loose, it could have spun in it's hub, with the hood open ans an observerstanding beside the car looking down at the axles, slowly let the clutch out (engine running, in reverse gear, ) being careful not to hit your assistant, if the axles turn- one of them, but the wheel doesn't this is your problem. If the axles don't turn with the clutch out, and engine still revs, well it's time for a clutch or transmission, Good luck, hoe this helps

Apr 27, 2010 | 2000 Subaru Outback

1 Answer

Unable to change down gear. gear lever stays down


Well, first of all ofcourse find out how many gears you have, if you take it to a shop and they tell you you have "One down, four up"
It means starting from Neutral, you click down once for first gear, and from there you can click up to fifth.
Try finding an open area, gear up to 3rd or 4th then gear down a couple times.
Remember, you must be in gear 2 or higher to gear down.

Jun 02, 2009 | 2003 kawasaki Z 1000

1 Answer

Cant shift unless i compression shift


Chances are pretty good your clutch is toast ! If your truck has a hydraulic clutch , in which mine doesn't , get a friend to pull the boot off of the clutch fork , and with a light , make sure it is disengaging the clutch at all . If you have a mechanical clutch , simply adjust it out til the problem goes away . Look forward to a new clutch very soon ! good luck !!

Apr 20, 2009 | 1992 Chevrolet C2500

1 Answer

Mixers eating brass gear driven by motor pinon


Thats called a sacraficial gear because its brass which is a soft metal.This gear takes most of the strain but i think either a spacer is missing or the gears arent meshing correctly.The transmission assembly the shaft next to it make sure all the spacers/washers are there.Goto hobartcorp.com you will find an exploded parts breakdown.

Aug 29, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
2008 Yamaha YZF-R125 Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...